Ubiquiti UniFI UAP-AC Manuale utente
Enterprise WiFi System
Model: UAP-AC
1
Introduction
Introduction
Thank you for purchasing the Ubiquiti Networks™UniFi™Enterprise
WiFi System. The UniFi Enterprise WiFi System includes the UniFi
Controller software, which allows you to manage your wireless
network using a web browser.
This Quick Start Guide includes the warranty terms and is for use
with the UniFi AP-AC, model UAP-AC. The UniFi Enterprise WiFi
System also includes the necessary hardware for mounting the
unit on a wall or a ceiling. The UniFi AP can be powered by any of
the following:
• PoE GigE Adapter (included)
• PoE+ 802.3at compliant switch
• Ubiquiti Networks TOUGHSwitch PRO, model TS-8-PRO
Package Contents
UniFi AP AC Mounting Bracket Ceiling Backing Plate
M3x50 Flat Head
Screws (Qty. 4)
M3 Keps Nuts
(Qty. 4)
M2.9x20 Screws
(Qty. 4)
M3x20 Screw
Anchors (Qty. 4)
Enterprise WiFi System
Model: UAP-AC
UniFi Controller
CD with User Guide
PoE GigE Adapter
(48V, 0.5A Gigabit)
Power Cord Quick Start Guide
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customer’s responsibility to
follow local country regulations, including operation within legal frequency channels, output power,
indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements.
2
UniFi™AP-AC Quick Start Guide
System Requirements
• Microsoft Windows Vista, Windows 7, Windows 8, or Mac OS X
• Java Runtime Environment 1.6 (or above)
• Web Browser: Mozilla Firefox, Google Chrome, or Microsoft
Internet Explorer 8 (or above)
Network Topology Requirements
• A DHCP-enabled network (for the AP to obtain an IP address as
well as for the wireless clients after deployment)
• A management station computer running the UniFi Controller
software, located either onsite and connected to the same
Layer-2 network, or off-site in a cloud or NOC
or
Router
O-Site
Cloud/NOC
On-Site
Management Station
UAP-AC
UAP/UAP-LR
UAP-PRO
UAP-Outdoor
Sample Network Diagram
All UniFi APs support off-site management controllers. Refer to the
User Guide on the CD for setup details.
3
Hardware Overview
Hardware Overview
LED
LED Color Status
Flashing white Initializing.
Steady white Factory default, waiting to be integrated.
Alternating
white/blue
Device is busy; do not touch or unplug it.
This usually indicates that a process such as a
firmware upgrade is taking place.
Quickly flashing
blue
This is used to locate an AP.
When you click Locate in the UniFi Controller
software, the AP will flash. It will also display
the location of the AP on the map.
Steady blue Indicates the device has been successfully
integrated into a network and is working
properly.
Steady blue
with occasional
flashing
Indicates the device is in an isolated state (all
WLANs are brought down until an uplink is
found).
4
UniFi™AP-AC Quick Start Guide
Ports
MAIN SECONDARY
Reset
Thisdevice complies with Part 15 of FCC rules.
Operationis subject to the following 2 conditions:
1)this de vice may not cause ha rmful interfe rence
and, 2) this device must ac cept any interfe rence
received,including interfe rence that may cause
undesiredoperation.
FCC ID: SWX- UAPAC IC: 6545A-UAPAC
0560
M/N: UAP- AC 48V 0.5A POE
AP AC
|
Main Port Secondary Port
Reset Button
Cable Feed Plug
Locking
Notch
Locking
Clip
Mounting Bracket
Main The Main port is a Gigabit Ethernet port used to connect
the power and should be connected to the LAN and DHCP server.
Power can be provided by any of the following:
• PoE GigE Adapter (included)
• PoE+ 802.3at compliant switch
• Ubiquiti Networks TOUGHSwitch PRO, model TS-8-PRO
Secondary The Secondary port is a Gigabit Ethernet port used for
bridging.
Reset The Reset button serves two functions:
• Restart It will restart the device when you press and release it
quickly.
• Restore Factory Defaults When you press and hold it for more
then 5 seconds, it will restore the device to the factory default
settings.
Locking Clip During installation, the Locking Clip on the Mounting
Bracket locks into the Locking Notch on the UniFi AP to help
prevent easy removal of the UniFi AP.
Cable Feed Plug If your Ethernet cable feeds along the mounting
surface, remove the Cable Feed Plug.
5
Installation Requirements
Installation Requirements
• CAT5/6 cable
• Phillips screwdriver
• Drill and drill bit (6 mm for wall-mounting or 3 mm for
ceiling-mounting)
• Optional: Drywall or keyhole saw (to cut 25 mm hole for
Ethernet cable feed)
Hardware Installation
The UniFi AP can be mounted on the wall or ceiling. Perform the
steps for the appropriate installation:
Wall Mount
1. Position the Mounting Bracket at the desired location on the
wall with the cable feed slot pointed towards the floor.
2. Use a pencil to mark the four mounting holes. Use a 6 mm drill
bit to drill the mounting holes.
Top
Optional 25 mm Hole for
Ethernet Cable Feed through Wall
3. Follow the instruction for your type of Ethernet cable feed:
- Feeds Through the Wall Cut or drill a circle approximately
25 mm in diameter, just below the bottom center of the
Mounting Bracket (as shown above). Then feed the CAT5/6
cable through the hole.
- Feeds Along the Mounting Surface Remove the Cable
Feed Plug on the side of the UniFi AP.
6
UniFi™AP-AC Quick Start Guide
4. Insert the M3x20 Screw Anchors into the 6 mm holes. Secure the
Mounting Bracket to the wall by inserting the M2.9x20 Screws
into the anchors.
5. Connect the Ethernet cable to the Main port. If the feed is
along the mounting surface, feed the cable through the Cable
Feed of the UniFi AP.
MAIN SECONDARY
RESET
Thisdevice complies with Part 15 of FCC rules.
Operationis subject to the following 2 conditions:
1)this devi ce may not cause har mful interfere nce
and,2) t his device must acc ept any interfere nce
received,including interference that may cause
undesiredoperation.
FCC ID: SWX-U APAC IC:6545A-UAPAC
0560
M/N: UAP-A C 48V 0.5APOE
AP AC
|
7
Hardware Installation
6. Align the slots on the UniFi AP with the tabs on the Mounting
Bracket.
7. Slide the UniFi AP down until it locks into place.
8
UniFi™AP-AC Quick Start Guide
Ceiling Mount
1. Remove the ceiling tile.
2. Place the Ceiling Backing Plate in the center of the ceiling tile.
Mark the four mounting screw holes and 25 mm hole for the
Ethernet cable feed.
25 mm Hole for Ethernet Cable Feed
3. Use a 3 mm drill bit to drill the screw holes, and cut or drill the
hole for the Ethernet cable feed.
Altri manuali per UniFI UAP-AC
1
Indice
Altri manuali Ubiquiti Punto di accesso wireless
Ubiquiti
Ubiquiti PBE-M5-620 Manuale utente
Ubiquiti
Ubiquiti NanoStatonM Series Manuale utente
Ubiquiti
Ubiquiti UniFi USW-Flex-Mini Manuale utente
Ubiquiti
Ubiquiti Rocket 5ac PtMP Manuale utente
Ubiquiti
Ubiquiti UAP-PRO Manuale utente
Ubiquiti
Ubiquiti UAP-IW-HD Manuale utente
Ubiquiti
Ubiquiti LBE-5AC-Gen2 Manuale utente
Ubiquiti
Ubiquiti UF-Nano Manuale utente
Ubiquiti
Ubiquiti M900 Manuale utente
Ubiquiti
Ubiquiti UniFi AP AC Outdoor Manuale utente
Ubiquiti
Ubiquiti RP5AC-PRISM Manuale utente
Ubiquiti
Ubiquiti airCube ISP Manuale utente
Ubiquiti
Ubiquiti NBE--2AC--13 Manuale utente
Ubiquiti
Ubiquiti LiteBeam LBE-5AC-LR Manuale utente
Ubiquiti
Ubiquiti UBB Manuale utente
Ubiquiti
Ubiquiti UniFi UAP--AC--HD Manuale utente
Ubiquiti
Ubiquiti LiteAP ac LAP-120 Manuale utente
Ubiquiti
Ubiquiti LiteBeam AC GENZ Manuale utente
Ubiquiti
Ubiquiti UniFi UAP-FlexHD Manuale utente
Ubiquiti
Ubiquiti Rocket 5AC PTP Manuale utente
