Ublox EVK-M8 Manuale utente
2. Setup
1. Download and install the EVK-M8 software (and docu-
mentation) from www.u-blox.com/evk-search.
See installation notes on the back of this card.
2. Connect the unit to a PC. Options:
• USB: Connect via USB port (G). The USB driver
installs automatically when the device is
connected to a PC; internet connection required.
• UART: Connect via RS232 (F). Set switch (B) to I2C.
• SPI / I2C compliant DDC: Connect the pins (C).
Set switch (B) to either SPI or I2C.
NOTE: Press RST (E) after setting switch (B).
3. Provide power to the device at all times, either via USB
on the back (G) or the V5 IN pin (D) on the front.
4. Connect the GNSS antenna to the evaluation unit (A)
and place the antenna in a location with an unobstruct-
ed view of the sky. For best performance, use an active
antenna or external LNA (when connecting to a GNSS
simulator).
5. Start the u-center GNSS evaluation software and se-
lect the corresponding COM port and baud rate.
Quick Start for EVK-M8 kits
Copyright © 2018, u-blox AG
AC
UBX-13003205 - R04
D
B
E
1. Overview
FG
3. Kit includes
• EVK-M8 unit
• USB cable
• Active GPS / GLONASS / BeiDou antenna with a 3 m cable
5. Interfaces
The EVK-M8 can be used to evaluate all interfaces avail-
able on u-blox M8 chips and modules. The evaluation unit
provides a USB connector for communication and powering
the device, as well as a UART connector for connecting to
the COM port of your PC.
SPI and the I2C-compliant DDC interfaces are designed to
enable communications with a host CPU.
7. More information
NOTE: Refer to recommendations in the EVK user guide
when using the EVK-M8 with a GNSS simulator.
For more information about the EVK-M8, contact your
nearest u-blox support:
www.u-blox.com/contact-technical-support
UBX-13003205 - R04
4. Installation
Notes for downloading the EVK-M8 software package and
running the installation:
• An Internet connection is required
• Supported Windows operating systems: Windows 7
onwards (x86 and x64 versions)
• Download the u-center evaluation software
• Run the u-center installer executable le and follow the
installer instructions
• When the installation is complete, you will nd a
u-center menu under the Windows Start button,
All Programs > u-blox
6. u-center
The u-center GNSS evaluation software provides a powerful
tool for evaluation, performance analysis and conguration
of u-blox positioning products.
Altri manuali Ublox Hardware per computer
Ublox
Ublox USB-ANNA-B4 Manuale utente
Ublox
Ublox NEO-D9S Manuale utente
Ublox
Ublox AWS ExpressLink SARA-R5 Manuale utente
Ublox
Ublox EVK-NORA-B1 Manuale utente
Ublox
Ublox XPLR-AOA-1 Manuale utente
Ublox
Ublox JODY-W1 Series Guida rapida alla configurazione
Ublox
Ublox EVK-7PAM Manuale utente
Ublox
Ublox ANT-B10 Manuale utente
Ublox
Ublox C099-F9P Manuale utente
Ublox
Ublox EVK-NINA-W13 Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
