UFO MicroLED 3000 Scheda tecnica
PRODUCT USER GUIDE
M croLED 3000 L ght Source
PLEASE READ THIS USER GUIDE BEFORE INSTALLING, OPERATING
OR PERFORMING MAINTENANCE ON THE LIGHT SOURCE UNIT
E357731
Rev: C1
INTRODUCTION
MICROLED 3000 USER GUIDE
2
Thank you for purchasing this UFO light source/luminaire.
To ensure that the light source is set up optimally and gives a long service life, please read this
user guide before installing, operating or performing any maintenance on the unit.
Please keep this User Guide for future reference. This User Guide is laid out in three sections
Installation -details on how to connect your luminaire
Operation - details how to programme and set up your luminaire
Maintenance - maintenance log, troubleshooting guide, technical specification
MODELS COVERED BY THIS USER GUIDE
IMPORTANT
This product must be installed in accordance with the applicable installation code, by a person
familiar with the construction and operation of the product, and the hazards involved.
These light sources are not mains dimmable.
The LED array in this light source is not replaceable. When it reaches end of life the whole unit
must be replaced.
Type Y Attac ment: If the external flexible cable or cord of this luminaire or associated
PSU/driver is damaged, it shall be exclusively replaced by the manufacturer or his service agent
or a similar qualified person to avoid a hazard.
Location: Do not locate this light source closer than 200mm from any flammable surface.
Clearance / Ventilation: It is imperative that a gap of 200mm is le around the unit. This is to
allow air to circulate and prevent overheating. The location must have free ventilation and must
not have an ambient temperature higher than that specified for the luminaire.
Mounting: This luminaire comes with an integral mounting plate for securing the unit to a
vertical or horizontal surface. Refer to the instruction sheet supplied with the plate.
Warning: Never look directly at the luminaire through the fibre port of the light source.
Warning: The luminaire should be positioned so that prolonged staring into the
luminaire at a distance closer than 2.7 metres is not expected.
UFO MIC3000
This light source is supplied with a separate mounting plate. If using the mounting plate refer to
the fitting instructions supplied with it.
MOUNTING
INSTALLATION
3
UFO LIGHTING
This light source is powered by a 12V Power Supply Unit or 12V Constant Voltage Driver.
Remove the PSU/driver from its box.
Connect the ack plug into the socket in the back, and the light source is now ready for
connection.
POWER SUPPLY REQUIREMENTS
There are 3 connections required – the 2 fibre ports and the mains supply. The fibre port
should be connected first. Connect and secure the fibre optic connector into the front of the
unit and secure using the M5 locking screw
Plug the mains plug into the electrical supply socket. Switch on power the led Indicator will
illuminate and the light source will start up automatically. If no light is produced consult the
TROUBLESHOOTING section
NOTE: THESE LIGHT SOURCES ARE NOT MAINS DIMMABLE.
CONNECTION
MIC3000 REMOTE CONTROLLER
Descripon Details Comments
Power 2 X AAA baeries
Range 30 metres
Measured in free space, may
be aenuated by obstrucons
or other RF devices
Frequency 2.4GHz Approved for use in UK,
Europe and USA.
Batteries – With The LED Light Source powered up as described above, remove the rear cover
on Remote Controller. Taking care not to touc any of t e front cover buttons, insert the
batteries. If you touch the remote control buttons when inserting the batteries it WILL
effect the operation of your Remote Control. If you do accidentally touch any of the buttons,
remove the batteries and start again.Once the batteries are inserted do not use the
Remote Control for 3 seconds.
DO NOT TOUCH THE BUTTONS WHILST INSERTING BATTERIES
Test remote control functions as detailed on page 5. The Remote Controller is “matched”
to the Light Source at the factory. If the Remote Controller is not matched or an additional or
replacement Remote Controller is required (see NOTE 2) for the Light Source proceed to the
Matching Mode as follows. If a Remote Controller is to be removed from control of a Light
Source proceed to Unmatching Model on page 5.
OPERATION
MICROLED 3000 USER GUIDE
4
REMOTE OPERATION
1. ON
2. OFF
4. Indicato light 3. Colou ing
5. Speed +
9. Mode +
6. B ightness +
7. B ightness -
8. Speed - 10. Mode -
No Descripon Funcon
01 Buon Power ON
02 Buon Power OFF
03 Colour ring Touch control all colours
(White not available)
04 Indicator Indicates Controller acve when
buons pressed
05 Buon Increase colour cycle speed
06 Buon Increase brightness
07 Buon Decrease brightness
08 Buon Decrease colour cycle speed
09 Buon Mode + Step up through Colour
cycle programmes
10 Buon Mode - Step up through Colour
cycle programmes
OPERATION
5
UFO LIGHTING
Matc ing Remote to Lig t Source– Remove the power plug from the rear of the Light Source,
then replace and touch button 5 within 3 seconds, the Light Source will “blink” twice slowly
indicating that the Remote Controller is matched to the Light Source.
Unmatc ing Remote from Lig t Source- Remove the power plug from the rear of the Light
Source, then replace and touch and hold button 5 within 3 seconds and the Light Source will
“blink” 9 times indicating that the Remote Controller is unmatched from the Light Source.
NOTE: - More than one Light Source controlled by one Remote Controller will eventually run
out of sync with each other (colour cycle mismatch)
REMOTE CONTROLLER OPERATION
OPERATION
MICROLED 3000 USER GUIDE
6
No Mode Brightness Speed Comment
01 Stac white Adjustable Not adjustable
To revert to 1 (Stac White) at
any me touch Colour Ring
then Mode+
02 White and Colours
mixed Adjustable Not adjustable
Colour Ring control – brightness
adjust Colour only, not White. To
revert to 2 (Colour Ring) at any
metouch colour ring
03 All Colours fade
change Adjustable Adjustable No White
04 RGBW fade change Adjustable Adjustable Red, Green, Blue & White
05 7 colours snap
change Adjustable Adjustable Red, Green, Blue & White
06 2 colours snap
change Adjustable Adjustable White and colours mixed
07 2 colours snap
change Adjustable Adjustable Red & White
08 2 colours snap
change Adjustable Adjustable Red & Whitee
09 2 colours snap
change Adjustable Adjustable Green & White
10 1 colour ash Adjustable
programmes Adjustable Red
11 1 colour ash Adjustable Adjustable Blue
12 1 colour ash Adjustable Adjustable Green
13 1 colour ash Adjustable Adjustable White
14 All colours
snap & fade Adjustable Adjustable Random
MODE FUNCTION PROGRAMME LIST
Mode Buttons – This is not a loop, i.e. touching the Mode+ button will not eventually bring
you back to Mode 1. To revert to Mode 1, either touch Mode – button repeatedly to step back
up through the Mode numbers, or touch Colour Ring then Mode+
Colour Ring –The Colour Ring can be used to select individual colours by touching the ring
and sliding your finger around the ring,
Brig tness – brightness can be increased or reduced in any mode using buttons 6 & 7
Cycle Speed – speed of colour cycling in Modes 3 to 14 can be ad usted using buttons 5 & 8
OPERATION
7
UFO LIGHTING
Once the Light Source is fully installed carry out a complete range walk test and record the range in
the table below. This information is essential for maintenance purposes to determine if the
range/sensitivity is reducing and also to record dead areas within the Remote Controller’s range
due to RF obstructions and/or RF interference.
NOTE : Where a Light Source has more than one Remote Control, reduction in operating range may
be experienced when both (or multiple) Remote Controls are used simultaneously.
REMOTE RANGE WALK TEST
Descripon Date Max Range
Controller 1
Controller 2
Controller 3
Dead Areas
To disable the remote and revert to manual operation press one of the buttons on the rear of the
Light Source. The Light Source will now respond to manual commands from the 2 control buttons
as detailed below.
The LED Light source has 2 colour cycles each with 3 different speed settings as detailed below.
STANDALONE OPERATION
OPERATION
Cycle Colour 1 Colour 2 Colour 3 Colour 4 Colour 5 Colour 6 Colour 7
1 White Red Orange Jade Green Cyan Blue
2 Red Orange Jade Green Cyan Blue White
OPERATION
MICROLED 3000 USER GUIDE
8
The Light Source is controlled using the 2 push buttons on the rear of the unit.
The Lower button STOPS and STARTS the colour Cycle.
The Upper button is used to select the Cycle speed as follows. Push the Lower button
repeatedly until the colour White is displayed. The light source is now in Cycle 1 speed A as
detailed below. Each push reduces the speed. On the third push the colour Red will be
displayed. The light source is now in Cycle 2 speed A.
Cycle SPEED A - Fastest SPEED B - Slower SPEED C - Slowest
1 (White Start) Push Once Push Once Push Once
2 (Red Start) Push Once Push Once Push Once
At any time the cycle can be stopped on a colour and started again using the Lower push button.
To disable manual operation and revert to remote controller operation, recycle the power to
the Light Source. The Remote Controller may need to be matched to the Light Source as
detailed on page 5.
The MicroLED 3000 is programmed as a Master unit (See Mode designation label on rear of unit)
and is capable of interlinking to and controlling MicroLED Slave Light Sources using a RJ45 cable
linking the two. In this Master /Slave configuration the Slave Light Source will follow the Master Light
Source. The MicroLED 3000 Master Light Source, cannot be controlled by a remote DMX controller.
For the MicroLED 3000, remote DMX slave control can only be achieved with MicroLED 2000 or
MicroLED 4000 Slave Light Sources. See MicroLED 2000 or MicroLED 4000 Slave User Guides for
DMX wiring connections
DMX OPERATION
OPERATION
9
UFO LIGHTING
MAINTENANCE LOG
Date Maintenance Undertaken
Note: A record of all maintenance MUST be kept in the table above, indicating what maintenance
was undertaken and when. This MUST be dated for warranty purposes.
MAINTENANCE
MICROLED 3000 USER GUIDE
10
Indice
Altri manuali UFO Attrezzatura di illuminazione
UFO
UFO Vega SLP-2700M Manuale utente
UFO
UFO MicroLED 100PT Scheda tecnica
UFO
UFO IP-02 Scheda tecnica
UFO
UFO MIC100PT-3 Manuale utente
UFO
UFO Apollo Manuale utente
UFO
UFO Vega CM Scheda tecnica
UFO
UFO LPV2 Manuale utente
UFO
UFO MicroLED 100P Series Scheda tecnica
UFO
UFO LUNA SLP-3000M Manuale utente
UFO
UFO NOVA DMX Scheda tecnica
UFO
UFO MicroLED 1000P Scheda tecnica
UFO
UFO MIC4000x2 Manuale utente
UFO
UFO LUNA SLP-3000M Scheda tecnica
UFO
UFO UFO MER3000M Manuale utente
UFO
UFO MicroLED 4000P Scheda tecnica
UFO
UFO Quasar UFOQUA3080-A Manuale utente
UFO
UFO GEM SLP-3000M Manuale utente
UFO
UFO Vega Scheda tecnica
UFO
UFO MicroLED 1000P Scheda tecnica
UFO
UFO MicroLED 4000P Scheda tecnica
