UFO Illuminator 150 CDMXG Manuale utente
Compact DMX Illuminator
Models covered by this manual:
UFO 150 CDMXG-A Glass, DMX - 120V
UFO 150 CDMXP-A Plastic, DMX - 120V
Universal Fiber Optics LLC,
6119A Clark Center Avenue | Sarasota | Florida 34238
Tel : 1 (800) UFO 5554 | Tel : (941) 343 8115
www.fiberopticli htin .com
Illuminator User Guide
Issue 2 | Revised: 24072013
Compact DMX Illuminator Ran e
1
INTRODUCTION
Thank you for purchasin this UFO illuminator.
Please read these instructions fully before connectin your unit to the electrical
supply, and keep them for future reference.
The UFO Compact DMX are a ran e of low profile illuminators which use 150W metal
halide dischar e lamps to ive much reater bri htness than those powered by
halo en lamps.
These models have a fast re-lampin feature (the lamp is mounted on a pull out
hatch at the rear) and are fitted with a DMX controller allowin a ran e of in-built
effects or control via a standalone controller.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED
IMPORTANT
Do not operate without complete lamp enclosure in place or if lens is dama ed.
KEEP HARNESS IN PLACE WHEN IN OPERATION.
CAUTION: Hot surface. Keep away from curtains and other combustible materi-
als.
WARNING: RISK OF FIRE/INJURY TO PERSONS. Keep away from
combustibles. Unplu to chan e lamp. Do not touch lamp.
WARNING: RISK OF FIRE. Do not place lamp where the overhead surface is closer
than 0.2m to the illuminator.
Universal Fiber Optics 2
IMPORTANT SAFETY INFORMATION
1. Unplu and allow to cool before replacin lamp.
2. Lamp ets HOT quickly! Only contact plu when turnin on.
3. Do not touch hot lens, uard, or enclosure.
4. Do not remain in li ht if skin feels warm.
5. Do not look directly at li hted lamp.
6. Keep lamp away from materials that may burn.
7. Use only with a 150W or smaller lamp.
8. Do not touch the lamp at any time. Use a so cloth. Oil from skin may dama e
lamp.
9. Do not operate product with missin or dama ed uard, lamp containment
barrier, lens or fibre-optic harness.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO
PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Li hted Lamp is HOT:
WARNING – To reduce the risk of FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS:
• Always disconnect the unit from the power supply before openin or attemptin to
perform any work on it.
• UNIT MAY GET HOT - always allow unit to cool down before handlin or
movin it.
• Do not touch or attempt to remove the lamp while it is hot.
• Ensure that the power supply is correct for the unit before powerin it up.
• Always ensure that the unit is properly EARTHED.
• Do not expose the unit to rain or moisture.
• Keep away from all combustible materials.
• Never attempt to tamper with the wirin or other internal components.
• Keep the unit away from as, oil and any other flammable or explosive materials.
• Indoor use only.
SAVE THESE INSTRUCTIONS
Compact DMX Illuminator Ran e
3
ILLUMINATOR LAYOUT
Item Description
1 Fibre port connector
2 Control button
3 Control button
4 Display
5 Microphone
6 Coolin fan rille
7 XLR socket
8 XLR socket
9 Lamp holder
10 Mains input socket & fuse holder and power LED
11 Hole with cover to access fibre optic connector retainin screw
Universal Fiber Optics 4
INSTALLATION GUIDE
In order for the Compact illuminator to function safely and efficiently it must be
installed accordin to this user manual. Please read all sections thorou hly before
switchin on the illuminator.
POWER SUPPLY REQUIREMENTS
Before plu in in the unit, please make sure that the supply is correct. Failure to do
so could cause the unit to malfunction. The unit requires a 120VAC 60Hz supply and
it MUST BE EARTHED. The illuminator units are provided with a cordset fitted with a
standard 3-pin plu .
POSITIONING THE UNIT
The illuminator can be mounted horizontally, vertically or upside-down on any flat
surface. Keyhole slots are provided on the base of the unit to allow for securin to a
surface. The illuminator is only suitable for use in a dry area.
If the unit is bein mounted at a hi her than the round level, block access below
the work area before installin .
Verify that any screws or bolts can safely bear the wei ht of the illuminator.
Compact DMX Illuminator Ran e
5
INSTALLATION GUIDE (Continued)
Verify that the supportin structure can safely bear the wei ht of all installed units,
cables and any other equipment. The minimum thickness of the mountin surface
must be no less than 19mm.
For horizontal mountin , it is recommended that the illuminator is secured to a solid
surface usin 4 x M4 or M5 screws or bolts and the keyhole slots. This is particularly
important if the illuminator location is not at round floor level.
To mount the illuminator vertically, first securely install 4 x M4 or M5 screws or bolts
at the required distances so that they will line up with the keyhole slots. The
illuminator can then be mounted onto them and slid into position. The bolts or
screws MUST then be fully ti htened.
To mount the illuminator under a surface, first securely install 4 x M4 or M5 screws or
bolts at the required distances so that they will line up with the keyhole slots. The
illuminator can then be mounted onto them and slid into position. The bolts or
screws MUST then be fully ti htened.
It is recommended that a ap of 200mm (8”) or more is le around the unit. This is to
allow air to circulate and prevent overheatin . The location must have free ventila-
tion.
CLEARANCE / VENTILATION
Universal Fiber Optics 6
INSTALLATION GUIDE (Continued)
CONNECTION
There are 3 main connections required, the fibre port, the mains power and the DMX
connections. Connect and secure the fibre optic connector to the fibre port before
connectin the electrical supply. Never run the illuminator with the fibre connector
unplu ed. The fibre optic connector is secured into the port by removin the small
cover on the top of the illuminator (see item 11 on pa e 3), and ti htenin the
retainin screw. The cover should then be replaced.
DMX data connections are provided at the rear of the illuminator, connection details
as follows
Like all data networks the DMX cable should be terminated on the DMX OUT of the
last illuminator on the network usin a terminator plu
OPERATION
This illuminator can be operated in stand alone mode, or can be connected to a
compatible DMX controller.
In Standalone Mode the Compact DMX can be used as a sin le independent
illuminator or in a Master Slave confi uration with several illuminators connected
to ether usin DMX leads. In Master Slave confi uration all addresses are set the
same and whatever pro ramme is selected on the “Master” DMX illuminator will also
be observed on the “Slave” illuminators.
In DMX mode the DMX controller can be pro rammed to control Compact DMX
illuminators either in a block (all same addresses) or independently (all different
addresses).
Compact DMX Illuminator Ran e
INSTALLATION GUIDE (Continued)
OPERATION (Continued)
When the DMX illuminator is powered up the unit will RESET durin which, the
followin flashin messa e will be displayed on the front panel display
(Item 4 Pa e 1):
When the illuminator is RESET the followin messa e will be displayed:
This indicates the illuminator has been set to address 001 by default.
PROGRAMMING
At any sta e durin pro rammin , when chan es are made the DMX may o
throu h the RESET phase as described above – this is normal.
Chan in Address
To chan e the address press the 2 buttons to the le of the display (Items 2 & 3 Pa e
1) simultaneously once the small indicator in the bottom ri ht of the display will o
out. Scroll for the required address as follows:
Once the selected address is found, there will be a short delay (may RESET) until the
small indicator illuminates confirmin the address is set.
7
Universal Fiber Optics
INSTALLATION GUIDE (Continued)
PROGRAMMING (Continued)
Color Wheel Built in Pro ams
To access the built in pro rammes as described in the User Guide proceed as
follows. Press the 2 buttons to the le of the display (Items 2 & 3 Pa e 1)
simultaneously twice and the followin messa e will be displayed:
Aer a short delay (may RESET) the small indicator will flash confirmin pro ramme
mode P01 is set as shown below. The illuminator will display white li ht:
Scroll throu h the Built in Pro rams until the desired pro ramme is reached there
will be a short delay (may RESET) until the small indicator flashes confirmin the
address is set. The set pro ramme will now run. The pro ramme will only run if le
in this mode, returnin to the Address Mode will stop the pro ram runnin .
To return to Address Mode press the 2 buttons to the le of the display (Items 2 & 3
Pa e 1) simultaneously three times.
Note 1: There is an Auxiliary mode which may be displayed as shown below. This is
not used. If in this mode press the 2 buttons simultaneously twice to return to
Address mode:
Note 2: In Master/Slave and Remote DMX controller operation the small indicator
flashes to indicate DMX data transmission
8
Compact DMX Illuminator Ran e
9
BUILT IN PROGRAMS
Program n mber F nction
P01 White
P02 Yellow
P03 Green
P04 Oran e
P05 Ma enta
P06 Blue
P07 Cyan
P08 Jade
P09 W,Y,G,O,M,B,C,J - flash chan e 2 seconds
P10 W,Y,G,O,M,B,C,J - flash chan e 5 seconds
P11 W,Y,G,O,M,B,C,J - flash chan e 10 seconds
P12 W,Y,G,O,M,B,C,J - flash chan e 30 seconds
P13 W,Y,G,O,M,B,C,J - flash chan e 60 seconds
P14 W,Y,G,O,M,B,C,J - flash chan e 2 seconds
P15 W,Y,G,O,M,B,C,J - flash chan e 5 seconds
P16 W,Y,G,O,M,B,C,J - flash chan e 10 seconds
P17 W,Y,G,O,M,B,C,J - flash chan e 30 seconds
P18 W,Y,G,O,M,B,C,J - flash chan e 60 seconds
P19 W,Y,G- flash chan e 2 seconds
P20 W,Y,G- flash chan e 5 seconds
P21 W,Y,G- flash chan e 10 seconds
P22 W,Y,G- flash chan e 30 seconds
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali UFO Attrezzatura di illuminazione
UFO
UFO MIC100PT-3 Manuale utente
UFO
UFO UFO MIC100P-3 Manuale utente
UFO
UFO MicroLED 3000 Scheda tecnica
UFO
UFO MBL2 Manuale utente
UFO
UFO MicroLED 4000P Scheda tecnica
UFO
UFO Vega Scheda tecnica
UFO
UFO MICROLED 2000 Manuale utente
UFO
UFO MicroLED 100P Series Scheda tecnica
UFO
UFO MBL1 Manuale utente
UFO
UFO MicroLED 4000P Scheda tecnica
UFO
UFO Sirius Series Manuale utente
UFO
UFO GEM SLP-3000M Manuale utente
UFO
UFO MicroLED 4000P Scheda tecnica
UFO
UFO Unidrive CC9 Scheda tecnica
UFO
UFO IP-02 Scheda tecnica
UFO
UFO LPV2 Manuale utente
UFO
UFO MicroLED 100PT Scheda tecnica
UFO
UFO Vega CM Scheda tecnica
UFO
UFO MicroLED 4000P Scheda tecnica
UFO
UFO UFO MER3000M Manuale utente
