UltraLift MERCURY SLIM Manuale utente
PRODUCT MANUAL
MERCURY SLIM
CEILING TILT TV LIFT
2
TABLE OF CONTENTS
MERCURY SLIM
PRODUCT DIAGRAM ............................................................................................................................................................ 3
PRE-INSTALLATION............................................................................................................................................................... 4
INSTALLATION ...................................................................................................................................................................... 7
Mounting The TV Screen .................................................................................................................................................. 9
CABLE MANAGEMENT........................................................................................................................................................ 11
MOTOR LIMITS ADJUSTMENT............................................................................................................................................ 12
WIRING AND OPERATION .................................................................................................................................................. 13
WARRANTY AND RETURNS................................................................................................................................................ 15
MOVING PARTS
Do not obstruct operation of mechanism with fingers or any object. Injury or damage could
result. If adjusting the limits, do so prior to wiring into control systems.
RISK OF ELECTROCUTION
Do not connect any power to the lift until installation is complete.
Attach the display panel after the lift has been properly installed and tested.
WEAR PROTECTIVE EYEWEAR
During installation, this product, or parts of it may move in unexpected ways.
Always wear protective eyewear to ensure safety.
BE PREPARED
Organise your mounting hardware and have the necessary tools readily accessible be-fore
installation.
NOTE
Do not expose to extreme temperatures or corrosive materials.
Minimize exposure to the elements. This will void your warranty and reduce the life of the
product.
3
PRODUCT DIAGRAM
MERCURY SLIM
PRODUCT DIAGRAM
SIDE MOUNT ING HOLES
CORFLUTE COVER
TV HANGING RAILS
HANGING RAILS
SECURING ACCESS HOLES
LIFTING CABLES
GAS STRUT
MICRO SWIT CH
TUBULAR MOT OR
ADJUSTMENT ACCESS
4
PRE-INSTALLATION
MERCURY SLIM
PRE-INSTALLATION
BEFORE INSTALL:
•When choosing your lift, keep in mind variances of the display panel size due to things like speakers on
the side, top or bottom. These can increase the size of the lift that you will need. Check that the screen is
not larger than the maximum screen size allowed.
•Check above the ceiling for obstructions (i.e., water pipes, cables, and duct work) before beginning
installation.
•After establishing the correct location for the lift and display panel, cut a hole in the ceiling at the size
listed on the following page.
•Organise a qualified trades person to frame up the roof to accommodate the Spartan so that it can be
mounted in the correct position.
•Route AV cables from the source to the roof location where the Lift will be in-stalled.
•Ensure that a double power point has been installed in the roof (or where suit-able) so that the Lift and
display panel can receive power.
•Before mounting the display panel to the Lift, ensure that it will suit the Lift in relation to dimensions,
loading capacity and functionality.
•Read instructions completely before proceeding. Follow instructions carefully. Installation contrary to
instructions invalidates warranty.
CAUTION
•Do not obstruct operation of lift with fingers or any object. Injury or damage could result.
•Check above the ceiling for obstructions (i.e., water pipers, cable, and duct work) before beginning
installation.
•Do not connect any power to the lift until installation is complete
•Attach the display panel only after the lift has been properly installed and tested.
•Unit operates on a 240V with a current draw of 1A and a 6.5mA standby.
•If adjusting the limits, do so prior to wiring into control systems.
•Organise your mounting hardware and have the necessary tools readily accessible before installation.
IMPORTANT WARNING
Follow cable spooling orientation as shown below when installing new motor and adjusting
limits. See the page for motor limit adjustment, motor type, and wire colour combination for
more information.
5
PRE-INSTALLATION
MERCURY SLIM
It is critical that the tension of the cables on the Mercury remains unchanged.
Changing the tension of the cables will damage the Mercury and void your warranty.
To ensure the tension remains unchanged from factory defaults, please note the following:
•NEVER open or close the Mercury lift manually (i.e., by hand):
Doing so may reduce the tension in the cables, causing them to bunch up on the tubular motor and
prevent the lift from raising or lowering properly. The cables may snap if this is the case.
8 mm Threaded Rod to Fasten Mercury to
Concrete Slab above Ceiling
LIFTING CABLE
Should Spool from Top of the Drum Down and
Should Never be Crossed Over as It Could
Fray and Ultimately Snap the Cable
Micro-Switch
Motor Junction Box
6
PRE-INSTALLATION
MERCURY SLIM
•NEVER disconnect the spool cables:
Doing so will cause the tension of each cable to become uneven/unbalanced, making the load
applied to the lifting mechanism uneven. This can cause the Mercury Lift to malfunction and may
cause the cables to snap.
Preparation:
1. Prepare the ceiling cut-out according to the Ceiling Cut-out sizes (CW and CD) in the Specifications of your
lift.
2. Frame up the ceiling joists or hanger rails using a qualified trades person.
3. Route the Audio-Visual cables to the lift position in the ceiling.
4. A double power point is required in the ceiling to power the Mercury Slim and the display
panel.
Note
•Access to the power point in the ceiling is advisable
7
INSTALLATION
MERCURY SLIM
INSTALLATION
1. Cut 8 mm threaded rods to suit the distance from
the slab/hanger rails to the Lift fixing points on the
top corners of the Mercury Slim.
2. Fix the pre-cut threaded rod to the slab or ceiling
hanger rails as shown below.
3. Fit one M8 nut and washer to each threaded rod.
4. Fit one M8 nut and washer 100 mm up from the
bottom of the threaded rod.
5. Raise the Mercury Slim unit into the pre-cut hole
from the underside. Fit the threaded rod through
the top frame of the lift. Fit nuts and washers to suspend the lift.
6. Adjust nuts until the lower frame sits 1-2mm above the plaster underside. Screw a minimum of four
M8 x 50 coach screws through the fixing holes on the inside frame of the Lift, into the pre-built
timber support frame.
M8 All Thread
Leng th as requ ired with
Nuts and washers.
8
INSTALLATION
MERCURY SLIM
7. Cover the bolts with the supplied end caps.
8. Route the AV cables into the lift as per diagram on page 13 (cable management).
9. Expose the IR eye in a suitable position to achieve line of sight to the remote.
10. Expose double sided tape on loose corflute dust cover and fit to frame.
Fasten 4 Coac h
Screws into Ceili ng
Joi sts throughholes in
the framework.
Cover coach
Screws with white
Plas�c end caps.
9
INSTALLATION
MERCURY SLIM
Mounting The TV Screen
1. Connect power to the lift and lower the lift using the IR remote control handset
2. Disconnect power to the lift
3. Remove the Mounting Rails by loosening the two 5mm locking screws.
4. Fit the rails to the back of the TV screen and bolt using the four Phillips head screws and washers, as per
diagram below, noting the orientation from the top of the screen to the top of the rails.
10
INSTALLATION
MERCURY SLIM
5. Lift the display Panel and hook rails onto the lift.
6. Tighten the locking screws to lock the rails into position, ensuring that the screws are tight.
7. Ensure the display panel is mounted centrally
Step 5: Lift displ ay panel
and hookrails onto lift.
Step 6: Tighten
locki ng screws
to lock the rails
in to positio n.
Indice
Altri manuali UltraLift Sistema di sollevamento
Manuali Sistema di sollevamento popolari di altre marche
Genie
Genie Z-60/34 Manuale utente
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manuale utente
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manuale utente
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manuale di programmazione
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manuale di programmazione
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manuale di programmazione
