Ulvac GHD-101A Manuale utente

No. 1000902-2-01-2

Instruction Manual

Direct drive oil-sealed rotary vacuum pump

Model

GHD-101A

GHD-101B

GHD-101C

GHD-101D

Read this manual before using the product.

Keep it in a safe place ready for use as necessary.

The content of this manual is liable to change without prior notice in

the event of improvements in performance and capabilities.

ULVAC KIKO, Inc.

-01-

０．Introduction

0.1 Before using the vacuum pump

Thank you for your purchase of the vacuum pump.

After receiving the pump, check it against the details of the order, and verify that

there has been no damage in transit.

Always read this manual thoroughly before installation, operation, inspection, and

maintenance to ensure that the pump retains its performance over the long-term, and

ensure that you understand the safety cautions, pump specifications, and method of

operation.

Copying of any part of this manual for use by a third party is prohibited without

permission of Ulvac.

Warning

Attention

-02-

0.2 Safety icons

This manual and the pump warnings include safety icons to assist in understanding

points to be followed.

The meanings of these icons are as described below.

There is a very real danger of death or serious injury to the operator if the equipment

is used incorrectly.

There is a danger of death or serious injury to the operator if the equipment is used

incorrectly.

There is a danger of moderate injury or disability to the operator, or physical damage,

if the equipment is used incorrectly.

There is a possibility of damage to the equipment, or problems with operation, if the

equipment is used incorrectly.

The surface of the pump may be very hot (40-80ºC). Use appropriate protection to

avoid direct contact with these surfaces. Incorporate the pump into equipment for

use.

Contact with the motor will result in electric shock. When connected to a power

supply, disconnect the power supply plug, and check that power is no longer

supplied.

Pump intake

Pump exhaust

Danger

Warning

Caution

Attention

Warning

-03-

0.3 Safety cautions

Ensure that only dry air or dry nitrogen enters this pump.

If the pump has been used to exhaust toxic gases, the pump itself, and the vacuum

pump oil (pump oil) will also be toxic. Be aware of this when performing maintenance.

Ensure that this pump is dismantled and repaired only by a repair technician. Failure

to follow this requirements may result in abnormal operation or electric shock.

Always ensure that the main power supply has been disconnected before inspecting

or repairing. Failure to do this may result in electric chocks or injuries due to the

pump suddenly starting.

Ensure that the equipment is earthed correctly. Installation of an earth leakage

breaker is recommended. Failure to earth the equipment correctly may result in

electric shock in the event of a malfunction or earth leakage.

Do not operate the pump with the exhaust blocked, or with the passage of gas on the

exhaust side obstructed. Under these conditions, the pump pressure increases, and

this may cause it to burst, oil to spray out of the oil level gauge, or the motor to

become overloaded.

The pump is not pressure-resistant, and has an internal pressure limit of 0.03 MPa

(gauge pressure).

Danger

Warning

-04-

Do not use the pump in an explosive atmosphere. Use under such conditions may

result in fire.

Do not put your fingers or anything else in the motor openings. Failure to follow this

requirement may result in electric shocks, injuries, or fire.

Do not touch the rotating parts such as the motor, shaft or joints while the pump is

operating. Failure to do so may result in injury or fire.

Ensure that the vicinity of the motor and pump is completely free of inflammable

material. Failure to follow this requirement may result in fire.

Ensure that the vicinity of the motor is free of obstacles which may obstruct

ventilation. Obstructed ventilation may result in fire.

The pump becomes very hot during operation, and it should therefore not be

touched, either in operation or immediately after it has stopped. Contact with the hot

pump may result in burns.

Ensure that all wiring work is performed in accordance with electrical equipment

standards and internal wiring regulations. Incorrect wiring work may result in fire.

If the pump ceases to operate, or a fault occurs, switch the main power supply off

immediately to prevent any accidents, and contact your dealer or Ulvac, for

inspection and repair.

Do not operate the pump when it doesn’t have any pump oil in it. It will break the

pump.

Warning

Caution

Attention

-05-

0.4 Receiving and storing the pump

0.4.1 Receiving the pump

The pump has been shipped with great care, however the following

procedure is recommended once the packing has been removed.

(1) Check that the product is as ordered.

(2) Check that all the accessories are there.

(3) Check that no damage has occurred in transit.

(4) Check that no nuts or bolts have become loose in transit. Have any nuts

come off?

Contact your dealer or Ulvac if a problem has occurred.

0.4.2 Surroundings during storage, mounting, and operation

This pump is designed with very tight tolerances, and the following conditions

must therefore be satisfied during storage, mounting, and operation.

(1) Temperature and humidity in operation: humidity at 7ºC – 40ºC, 85% or

less RH

(2) Maximum height above sea level during storage and operation: 1,000 m

(3) Other (during storage and operation)

a) No corrosive or explosive gas.

b) No condensation.

c) No dust.

d) Installed indoors.

e) Not stacked on other items, or likely to fall.

f) Not in direct sunlight.

g) Not near a heat source.

h) Pump oil put in the pump and inlet port sealed with a cap if stored for a

long period of time.

i) Not stored with moisture inside pump.

The pump weighs 20kg or more, and lifting or moving it alone may therefore result in

injury. Failure to do so may result in injury. Always ensure that at least two people

perform the installation as shown in 3.1 Installation.

Caution

-06-

The pump will be damaged if it is subjected to shock it is overturned.

Always use the pump indoors.

Pump oil must be put in the pump and the inlet port sealed if storing it unused for a

long period of time.

Do not leave the pump unused with moisture inside it. Corrosion of pump

components is accelerated if it is left in this condition, and the pump may seize and

no longer rotate.

0.5 Protective Equipment

A single-phase motor is connected to this pump.

An overload protection device (automatic-recovery type thermal protector) is built-in

to the single-phase motor.

Other protective equipment (e.g. earth leakage breaker) is also recommended to be

fitted.

Use the motor only at the rated voltage. Use at a different voltage may result in the

overload protection not operating correctly, motor burnout, or fire.

Attention

Contents-1

Contents

0．Introduction ・・・・・・・・・・ 01

0.1 Before using the vacuum pump ・・・・・・・・・・ 01

0.2 Safety icons ・・・・・・・・・・ 02

0.3 Safety cautions ・・・・・・・・・・ 03

0.4 Receiving and storing the pump ・・・・・・・・・・ 05

0.4.1 Receiving the pump ・・・・・・・・・・ 05

0.4.2 Surroundings during storage, mounting, and operation ・・・・・・・ 05

0.5 Protective Equipment ・・・・・・・・・・ 06

1．Using the pump safely ・・・・・・・・・・ 1

1.1 Dangers unique to the pump, and safety measures ・・・・・・・ 1

1.1.1 Leakage of dangerous gases and substances・・・ 1

1.1.2 Electric shock ・・・・・・・・・・ 1

1.1.3 Bursting ・・・・・・・・・・ 2

1.1.4 High temperature ・・・・・・・・・・ 2

1.2 Safety data sheet (SDS) ・・・・・・・・・・ 2

2．Pump description ・・・・・・・・・・ 3

2.1 Performance details ・・・・・・・・・・ 3

2.2 Dimension drawings ・・・・・・・・・・ 4

3．Installation ・・・・・・・・・・ 5

3.1 Installation ・・・・・・・・・・ 5

3.2 Establishing an exhaust ・・・・・・・・・・ 6

3.3 Vacuum piping ・・・・・・・・・・ 7

3.4 Wiring ・・・・・・・・・・ 8

3.5 Fluctuations in the power supply voltage and frequency ・・・・・・・・・・ 11

DANGER

WARNING

CAUTION

Contents-2

4．Operation ・・・・・・・・・・ 12

4.1 Safety cautions ・・・・・・・・・・ 12

4.2 Starting ・・・・・・・・・・ 13

4.3 Operating when it is cold ・・・・・・・・・・ 13

4.4 Stopping ・・・・・・・・・・ 14

4.5 Backflow prevention device ・・・・・・・・・・ 14

4.6 Thermal protector ・・・・・・・・・・ 14

4.7 Gas ballast valve ・・・・・・・・・・ 15

4.8 Attaching the oil mist trap (option) element ・・・・・・・・・・ 16

4.9 Operation restrictions when attaching the oil mist trap (option) element ・・・・・・・・・・ 16

4.10 Magnetic coupling ・・・・・・・・・・ 17

5．Pump performance ・・・・・・・・・・ 18

5.1 Ultimate pressure ・・・・・・・・・・ 18

5.2 Exhaust velocity ・・・・・・・・・・ 18

5.3 Required power ・・・・・・・・・・ 18

6．Maintenance, inspection and repair ・・・・・・・・・・ 20

6.1 Maintenance ・・・・・・・・・・ 20

6.2 Periodic inspection ・・・・・・・・・・ 20

6.3 Pump oil change ・・・・・・・・・・ 23

6.4 Trouble checklist ・・・・・・・・・・ 25

7．Disposal ・・・・・・・・・・ 27

Contents-3

8．Maintenance parts ・・・・・・・・・・ 28

8.1 Maintenance parts list ・・・・・・・・・・ 28

8.2 Disassembly drawings ・・・・・・・・・・ 29

Warranty

Safety data sheet (SDS)

Conditions of Use Check Sheet (disassembly repair)

Sales and Service Contact Addresses

Tables and figures

Fig. 1 GHD-101 Sealed rotary vacuum pump dimension drawings ・・・・・・・・・・ 4

Fig. 2 How to move the sealed rotary vacuum pump ・・・・・・・・・・ 5

Fig. 3 Establishing an exhaust ・・・・・・・・・・ 6

Fig. 4 Vacuum chamber and basic piping connections ・・・・・・・・・・ 7

Fig. 5 Wiring drawings ・・・・・・・・・・ 8

Fig. 6 Power cord consent (Inlet EN60320-1) ・・・・・・・・・・ 8

Fig. 7 How to attach the fastener and electric cord ・・・・・・・・・・ 9

Fig. 8 Fluctuations in the power supply voltage and frequency ・・・・・・・・・・ 11

Fig. 9 Exhaust velocity curve ・・・・・・・・・・ 19

Fig. 10 Adding oil to the sealed rotary vacuum pump ・・・・・・・・・・ 24

Fig. 11 GHD-101 Sealed rotary vacuum pump disassembly drawings ・・・・・・・・・・ 29

Table 1 Pump performance ・・・・・・・・・・ 3

Table 2 Motor performance ・・・・・・・・・・ 4

Table 3 Electric cord selection criteria ・・・・・・・・・・ 9

Table 4 Thermal protector characteristics ・・・・・・・・・・ 14

Table 5 Periodic inspection table ・・・・・・・・・・ 22

Table 6 Trouble checklist ・・・・・・・・・・ 25

Table 7 GHD-101 Maintenance parts list ・・・・・・・・・・ 28

Annex. Safety data sheet (SDS)

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ulvac Pompa dell'acqua

Ulvac

Ulvac DOP-400SB Manuale utente

Ulvac

Ulvac DIS-90 Manuale utente

Ulvac

Ulvac DOP-301SB Manuale utente

Ulvac

Ulvac DA-121D Series Manuale utente

Ulvac

Ulvac CRYO-U Series Manuale utente

Ulvac

Ulvac PVD-180 Manuale utente

Ulvac

Ulvac MBS-053 Manuale utente

Ulvac

Ulvac GLD-137CC Manuale utente

Ulvac

Ulvac DOP-120SX Manuale utente

Ulvac

Ulvac UTM2300 Series Manuale utente

Ulvac

Ulvac UTM1600 Series Manuale utente

Ulvac

Ulvac VD151 Manuale utente

Ulvac

Ulvac DAT-50DA Manuale utente

Ulvac

Ulvac DA-41D Manuale utente

Ulvac

Ulvac DAL-181D Manuale utente

Ulvac

Ulvac GC-25Sa Manuale utente

Ulvac

Ulvac CRYO-U Series Manuale utente

Ulvac

Ulvac VD30C Manuale utente

Ulvac

Ulvac DTU-20 Series Manuale utente

Ulvac

Ulvac PRC-003A Manuale utente

Ulvac

Ulvac DIS-251 Manuale utente

Ulvac

Ulvac CRYO-U12H Manuale utente

Ulvac

Ulvac CRYO-U Series Manuale utente

Ulvac

Ulvac ULK-10A Manuale utente

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

Graco

Graco Husky 3300e Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente