Uniden UCSWITCH5 Manuale utente
© 2018 Uniden America Corporation Issue 1, May 2018
Irving, Texas
UCSWITCH5
UCSWITCH9
OWNER’S MANUAL
Uniden surveillance products are not manufactured and/or sold with the
intent to be used for illegal purposes. Uniden expects consumer’s use of
these products to be in compliance with all local, state, and federal law.
For further information on video surveillance and audio recording legal
requirements, please consult your local, state, and federal ocials.
Uniden constantly works on improving our products. This includes
updating our documentation with the latest rmware changes. Go to
www.uniden.com to nd the latest version of all documentation.
© 2018 Uniden America Corporation
All rights reserved.
CONTENTS
INTRODUCTION ................................................ 5
PACKAGE CONTENTS................................................ 5
FRONT PANEL .................................................. 6
UCSWITCH5.................................................................. 6
UCSWITCH9.................................................................. 6
LED Descriptions........................................................ 6
EXTEND MODE ........................................................... 7
RJ45 PORTS ................................................................. 7
REAR PANEL ................................................................ 8
Power Socket.............................................................. 8
Grounding Terminal.................................................... 8
Lock Hole.................................................................... 8
DEVICE INSTALLATION .................................. 8
INSTALLATION RECOMMENDATIONS..................... 8
Anti-Static Protection .................................................. 9
Lightning Protection.................................................... 9
MOUNTING REQUIREMENTS.................................... 9
PHYSICAL CONNECTION........................................... 9
RJ45 Port Connections............................................... 9
Check Cabling .......................................................... 10
Connect to Power Supply ......................................... 10
TECHNICAL SPECIFICATIONS..................... 10
FCC PART 15/IC COMPLIANCE .................... 12
ONE-YEAR LIMITED WARRANTY ................ 13
5
UCSWITCH5/UCSWITCH9
OWNER’S MANUAL
INTRODUCTION
UCSWITCH5 and UCSWITCH9 are 10/100Mbps PoE switches. They
provide 5/9 10/100Mbps auto-negotiation RJ45 ports, in which ports
1-4/8 support IEEE 802.3af PoE (15.4W) and IEEE 802.3at PoE+ (30W).
The whole PoE power output is 58W/120W. With Cat 5 Ethernet cable,
power and data can be simultaneously transmitted to APs, IP cameras, IP
phones, and other Power Devices).
In addition, UCSWITCH5 and UCSWITCH9 support Extend mode. With
enabling Extend mode and Cat 5e Ethernet cable, the transmission
distance of data and power can be up to 250m.
PACKAGE CONTENTS
Open your package and check the following:
ITEM QUANTITY
UCSWITCH5 or
UCSWITCH9
1
Power Adapter 1
Foot Pads 4
User Manual 1
Screws 8
Wall anchors (UCSWITCH5
only)
2
If any item is incorrect, missing, or damaged, please keep the original
package and contact the www.uniden.com for replacement immediately.
6
FRONT PANEL
UCSWITCH5
UCSWITCH9
LED Descriptions
LED STATUS DESCRIPTION
PWR
Solid The device is properly connected to the power
supply.
O The device is not connected properly to the
power supply.
POE-
MAX
Solid The PoE power reaches alarm status; the
avalable PoE power is less than 6W.
Blinking PoE power is at maximum.
O PoE power is working properly; the available
PoE power is more than 6W
LINK/
ACT
Solid The corresponding port is connected properly.
Blinking The corresponding port is transmitting data.
O The corresponding port is not connected or
connected improperly.
7
LED STATUS DESCRIPTION
POE
STATUS
Solid The corresponding port is connected to a
Powered Device (PD) and powers the PD
properly.
Blinking The corresponding port’s PoE output exceeds
30W.
O The corresponding port has no PoE power
output or no PD is connected.
N/A O Reserved
EXTEND MODE
If Extend mode is enabled:
MODEL STATUS DESCRIPTION
UCSWITCH5 O Ports 1 - 4: 100M
On Ports 1 - 4: 10M
UCSWITCH9 O Ports 1 - 8: 100M
On Ports 1 - 8: 10M
To guarantee Extend mode performance, use a
Cat 5e or better Ethernet cable and congure the
remote device’s speed and duplex to be “Auto
Negotiation.”
If Extend mode is disabled, the transmission
distance of PoE powering and data is up to 150m if
using a Cat 5e or better Ethernet cable.
RJ45 PORTS
MODEL 10/100 MBPS
RJ45 PORTS
UPLINK PORT
UCSWITCH5 4 1
UCSWITCH9 8 1
8
REAR PANEL
The rear panel comprises a power socket and a grounding terminal.
UCSWITCH9 also had a lock hole.
Power Socket
The included power adapter connects the device to power through the
power socket.
Grounding Terminal
If desired, connect a grounding cable (not included) for lightning electrical
discharge protection.
Lock Hole
(UCSWITCH9 only) If the UCSWITCH9 is installed in a high trac area,
use a laptop lock (not included) in the lock hole to prevent tampering.
DEVICE INSTALLATION
INSTALLATION RECOMMENDATIONS
Follow these recommendations to ensure your safety and your device’s
operation:
• Wear antistatic gloves while installing and connect the device to
power.
• Use the included power adapter to power the device.
• Make sure the input voltage matches the value which is marked on the
device’s label.
• Place the device in a well-ventilated and dry environment.
• Do not open the device case.
9
There is a seal covering one of the screws in the
device case. If the device needs repair, keep the seal
unbroken until a Uniden technician can make the repair.
The user should not break the seal covering the screw.
If the seal is broken, the userwill be responsible for any
damage.
• Disconnect the device from the power supply when cleaning it.
• Position the device away from strong electrical currents.
Anti-Static Protection
Dust may lead to electrostatic buildup. Keep the device and its
environment clean. (A regular dusting is necessary.)
Lightning Protection
In a thunderstorm, the electrical discharge from lightning may damage
the device. Make sure the device, the installation location, and power
outlet on the wall are well-grounded.
MOUNTING REQUIREMENTS
Read and follow these requirements:
• The mounting location is stable and sturdy.
• Place the device where required in a clean, dry, and well-ventilated
environment. Keep at least 4 in.(10cm.) free on all sides for cooling.
• Do not place any heavy or large object on the device.
• Paste the four foot pad stickers on the corresponding four corners of
the underside of the device
PHYSICAL CONNECTION
RJ45 Port Connections
The RJ45 port uses an Ethernet cable to connect the switch to remote
devices. Ports 1 - 4/8 support IEEE 802.3af and IEEE 802.3at PoE
supply. The PD can be wireless AP, IP phone or IP camera, etc.
10
IP Phone IP Camera
Router
RJ45 Connection Examples
UCSWITCH-9
NOTES:
• A Cat 5e or better Ethernet cable is recommended. As each RJ45 port
supports MDI/MDIX auto-negotiating, either parallel or crossover cable
is acceptable.
• The device supports dynamic PoE supply; it will power the PD
properly and automatically.
Check Cabling
Once installation is completed, check the device cabling as follows:
• The operating power supply should agree with rated input standard.
• Ports cables are connected correctly.
• If there is outdoor cabling, connect a lightning protector to the cable
before you plug the cable into the port.
Connect to Power Supply
1. Plug the power adapter into the power socket.
2. Plug the other end of the power adapter into DC power.
3. The PWR LED turns on.
TECHNICAL SPECIFICATIONS
UCSWITCH5 UCSWITCH9
INTERFACES
10/100MBPS RJ45 59
Questo manuale è adatto per i seguenti modelli
1
Indice
