Uniden UH064SX-2NB Manuale utente

UH064SX-2NB

UHF CB Transceiver

For more exciting new products please visit our website:

Australia: www.uniden.com.au

New Zealand: www.uniden.co.nz

Controls & Indicators

Included in your Package

• UH064SX-NBRadio(2)

• OperatingGuide

• BeltClip(2)

• ChargingCradlewithACAdaptor

• NiMHBatteryPack(2)

• EarpieceMic(2)

1 Antenna

2 PTT(Push-To-Talk)Key

3 MonitorKey

4 Keylock/CallKey

5 Memory/ScanKey

6 Channel/PowerHi-LoKey

7 Speaker

8 HeadsetJack

9 Select/PowerOn-OffKey

10 Volume/SelectUpKey

11 Volume/SelectDownKey

12 Microphone

13 ReceiveIndicator

14 TransmitIndicator

15 ChannelIndicator

16 DCSONIndicator

17 ScanIndicator

18 MemoryIndicator

19 PriorityChannelIndicator

20 CTCSSONIndicator

21 BatteryLevelIndicator

22 HITransmitIndicator

23 LoTransmitIndicator

24 CTCSSandDCSCode/Volume

 LevelIndictor

25 VolumeSettingIndicator

26 VOXIndicator

27 BusyChannelLockoutIndicator

28 KeypadLockIndicator

29 ChargingLEDs

1UHFCBTransceiverUNIDENUH064SX-2NB

Optional Accessories

• SpeakerMicrophone

• VoxHeadset•CarryCase

• CommercialAccessories

Getting Started

NOTE

Unidendoesnotrepresentthisproducttobewaterproof.

DonotexposethisproducttoRainorMoisture.

Battery Installation

YourUH064SX-2NBunitusestheincludedNiMHbatterypackforpower.

Theunitcanbepoweredwithoptional4AAAALKALINEbatteries.

NOTE

Ifyoudon’tusetheUH064SX-2NBforlongperiods,Uniden

recommendremovingthebatteries.TheUH064SX-2NBis

designedtoretaintheprevioususersettings.Thisfeature

willcontinuetouseasmallamountofbatterypowerwhile

theunitisswitchedoff.

OLD

NEW

Toavoiddamagetotheunitdonotmixoldandnew

batteries.

To install the batteries:

1. Makesureyourradioisoff.

2. Releasethebatterycoverclip,thenremovethe

  batterycover.

3. InsertNiMHbatterypackaccordingtothe

  orientationonthebatterypack.

  Insert4AAAALKALINEbatteries(notincluded)

  accordingtothepolaritysymbolsinsidethe

  batterycompartment.

4. Alignthebatterycovertabswiththe

  UH064SX-2NBtabholesthenreplacethecoverclip.

NOTE

Donotchargealkalineornonrechargeablebatteries.

2UHFCBTransceiverUNIDENUH064SX-2NB

Getting Started

3UHFCBTransceiverUNIDENUH064SX-2NB

Installing the Charge Cradle

1. PlugtheACadaptorintotherearofthechargecradleandintothe

  mainspower.

2. PlacetheUH064SX-2NBintothechargecradle.Thechargelightwill

  comeontoindicatetheunitischarging.

3. BeforeoperatingtheUH064SX-2NB,chargethebatterypackfor

  16hours.

NOTE

Donotchargealkalineornonrechargeablebatteries.

User License Information

NOTE

ThecitizenbandradioserviceislicencedinAustraliaby

ACMARadio-communications(CitizenBandRadio

Stations)ClassLicenceandinNewZealandbyMED

GeneralUserLicenceforCitizenBandRadioandoperation

issubjecttoconditionscontainedinthoselicences.

Getting Started

Belt Clip

To attach the belt clip:

Slidethebeltclipuntilitsnapsintoplace.

To remove the belt clip:

Toremovethebeltclip,pressandhold

beltcliplocker,slidethebeltclipatthe

sametimeuntilreleased.

Low Battery Alert

Ifthebatterylevelbecomeslow,thebattery

indicatoricononthedisplaybeginsashing.

Whenthebatteriesintheunitarelow,theunit

willgointoabatteryLowmode.TheTransmit

modeisdisabled.Replacethealkaline

batteriesimmediatelyorifyouareusingthe

NiMHbatterypack,placetheradioonthe

chargecradletorecharge.Fullchargewilltake

upto16Hrs.

Back Light

TheUH064SX-2NBhasanautomaticdisplaybacklightwhichremainson

for10secondsafterakeypress(allkeysexceptPTTkey).Thebacklight

willworkevenifthekeypadislockedbutwillnotworkduringlowbattery

alertmode.

4UHFCBTransceiverUNIDENUH064SX-2NB

BeltClipLocker

Operation

5UHFCBTransceiverUNIDENUH064SX-2NB

Power On/Off

1. PressandholdSELECT/ keytoturntheradioon.

  Achannelnumberwillappearonthedisplay.

2. PressandholdSELECT/ keytoturntheradiooff.

Volume

Press or keytoincreaseordecreasethe

volumelevel.‘VOL’iconappearsonthedisplay

whilevolumeisbeingadjusted.

Thereare8volumelevels.Level0(NoAudio)to

Level7(MaximumVolume).

Adjusting the Key Beeps

Yourradioemitsabeepeachtimeoneofthekeys

(exceptforthePTTkey)ispressed.

1. ToturnOFFthisbeep:Pressandhold /CALLkeywhileturning

  ontheradio.

2. ToturnONthisbeep:Pressandhold /CALL keywhileturning

  ontheradio.

Roger Beep

RogerBeepisaBEEPthatissenttonotifytheendoftransmission(bothPTT

andVOXtransmission.)RogerBeepcanbeheardthroughthespeakerwhen

KeyBeepison.RogerBeepistransmittedevenifKeyBeepisturnedoff.

However,RogerBeepwillnotbeheardfromthespeaker.

1.ToturnOFFRogerBeep:Pressandhold keywhileturningontheradio.

2.ToturnONRogerBeep:Pressandhold keywhileturningontheradio.

Keylock On/Off

1.Press /CALL keyfor1.5secondstoenterkeylockonmode.

2.Press /CALL keyfor1.5secondswhileinKeylockmodetoexit

 theKeylockmode.

NOTE

WhileinKeylockonmode,theUH064SX-2NBcanstill

receiveandtransmit.

Operation

6UHFCBTransceiverUNIDENUH064SX-2NB

Selecting a Channel

1. PressCH / HI / LOkeymomentarilytoactivatechannel

  selectmode.Thedisplayedchannelwillash.

2. Press or keytoselectthedesiredchannel.

NOTE

Refertochannelguidelinesonpage12.

ForAustralia,Channels05and35are

reservedforEmergencyCalls.

3. PressCH / HI / LOkeymomentarilytoexitchannel

  selectmode.Ifnokeyispressedwithin5secthe

  UH064SX-2NBwillexitfromthechannelselectmode.

To Transmit and Receive

TheUH064SX-2NBusestheUHF-CBChannels

(Channels 22 and 23 are for telemetry and

telecommand applications. Transmit is

inhibited on these channels).

1. Beforeyoutransmit,listenforactivityonthe

  selectedchannel.

2. Whenthechannelisclear,pressandholdthePTTkeytotransmit.

TXiconappearsonthedisplay.

Holdtheradiowithmicrophoneapproximately5cminfrontofyourmouth

withtheantennaatapproximately45°angleawayfromyourhead.Speak

inaclear,normalconversationalvoice.

3. Whenyouhavenishedspeaking,releasethePTTandlistenfora

  response.TX iconthendisappearsonthedisplay.Whilereceiving,

theRX iconisdisplayed.

Transmit Hi/Lo Power Select

PressandholdCH / HI / LOkeytoselectdesiredtransmit

level.HI iconwillappearonthedisplayformaximum

transmitlevel.LO iconwillappearonthedisplayfor

minimumtransmitlevel.TheRFtransmitpowerofthe

UH064SX-2NBisselectablebetween2.0W(Hi)

and0.5W(Lo).

Operation

Automatic Squelch Feature

TheUH064SX-2NBisequippedwithanAutomaticSquelchSystem

whichshutsoffweaktransmissionsandunwantednoise.

Monitor

Thisfeatureenablesuserstolistenforweaksignalsonthecurrent

channelatthepressofakey.

To use monitor

1. PressMONkey.TheRX iconwillash.

2. Releasewithin1.5secondsandtheunitexits

  Monitormode.

3. PressandholdMON keyfor2secondsforcontinuouslistening.

  Thereceivercircuitwillstayopen,lettinginboththenoise&weak

  signals.TheRX iconashesinthisstatus.

4. ToreturntonormalReceivemodepressMONkey.TheRX icon

  disappearsorstopsashinginthisstatus.

Scanning

ThescanfunctionscansallchannelswhicharestoredintheSCAN

CHANNELMEMORYandstopsatanactivechannel.IfaPRIORITY

channelhasbeenselectedthenthischannelwillbemonitoredforactivity

every3seconds.Whenthesignalstops,theUH064SX-2NBwaits

2seconds(ReplyDelay)beforescanningresumes.

To initiate scanning;

1. PressMEM / SCNkeymomentarilytobegin

  scanning.

  TheSCANiconisdisplayed.

2. PressSELECT / ,MEM / SCN , /CALL

  orPTTkeytocancel.

Whenscanstopsatabusychannel,pressing

CH / HI / LOkeywillresumescan.

7UHFCBTransceiverUNIDENUH064SX-2NB

Operation

Reply Delay

Whilescanning,theUH064SX-2NBstopsatabusychannelandreceives

atransmission.Whenthereceivedsignalisover,theunitwillwaitfor2

secondsforthereturnofthesignal,otherwise,theradioresumesscanning.

To Operate in Duplex Mode (Repeaters)

TheDuplexfunctionenablesyoutoaccesslocalrepeaterstations.You

canonlyactivateDuplexfromCH01-CH08andCH41-CH48.

UHFCBRepeatersareusedtoretransmitorrelayyoursignal.Repeaters

willextendtherangeofyourradioandovercometheshieldingeffect

causedbysolidobstructions.

NOTE

Contactyourretailerforalistofrepeatersavailableinyour

area.

Operation With the Aid of a Repeater

1.PressSELECT / keysixtimes. appearsonthedisplay.

2.Press or tochange to forCH01-CH08and to for

 CH41-CH48.

3.PressSELECT / toconrm

Todeactivatetheduplexoperationrepeatactivationprocessandchange

to or to .UH064SX-2NBwillreturntonormaloperation.

NOTE

If or ispressedwhenthechannelisnotfrom

CH01-CH08orCH41-CH48,anerrortonesounds.

8UHFCBTransceiverUNIDENUH064SX-2NB

Operation

CTCSS & DCS

(Continuous Tone Coded Squelch System) & (Digital Coded Squelch)

CTCSSisafeaturethatallowsagrouptotalktoeachother

withouthearingotherusersonthesamechannel.

1. PressSELECT / keymomentarilytoenterCTCSS

  mode.ThecurrentselectedCTCSStoneashes.

2. Press keytoselecttherequiredCTCSS

  tone(OFFor1-38).

3. PressSELECT / keysixtimestoconrmthe

  selectedsettingandexittostandbymode.

ForchannelswithaCTCSStonesetting,theCTCSStoneisdisplayed

belowthechannelindicator.ForchannelswiththesettingofCTCSS

OFF,therewillbenodisplaybelowthechannelindicator.

DCSisadigitalextensionofCTCSS.Itprovides104extra,digitally

coded,squelchcodesthatfollowafterthe38CTCSScodes.CTCSS

1-38,followedbyDCS1-99plusDCS100-104(representedbyo0-o4on

thedisplay).

1. PressSELECT / keymomentarilytoenterCTCSS/DCSmode.

2. Use keytoselectaDCScode.TheDCScodes

  followonaftertheCTCSScodes.TheDCSiconwill

  replacetheCTCSScodeonthedisplay.

3. PressSELECT / keysixtimestoconrmthe

  selectedsettingandexittostandbymode.

  TheDCSiconwillappearwhenselected.Toturn

  offDCSselectCTCSSOFFandnodisplaywillshow

  belowthechannelindicator.

NOTE

Channels05and35areusedforemergencychannels.

CTCSSandDCSwillnotoperateonthesetwochannels.

9UHFCBTransceiverUNIDENUH064SX-2NB

Indice

Altri manuali Uniden Ricetrasmettitore

Uniden

Uniden UH755 Series Manuale utente

Uniden

Uniden UH825 Series Manuale utente

Uniden

Uniden SMH250D Manuale utente

Uniden

Uniden JACKSON Manuale utente

Uniden

Uniden UH043SX-2NB Manuale utente

Uniden

Uniden UH001 Manuale utente

Uniden

Uniden GPS105 Manuale utente

Uniden

Uniden MHS115 Manuale utente

Uniden

Uniden UH8055S Manuale utente

Uniden

Uniden MHS127 Manuale utente

Uniden

Uniden UH35 Series Manuale utente

Uniden

Uniden UH5040R Manuale utente

Uniden

Uniden Grant LT Manuale utente

Uniden

Uniden PRESIDENT JACKSON Manuale utente

Uniden

Uniden UH5000 Manuale utente

Uniden

Uniden Sundowner UH-077 Manuale utente

Uniden

Uniden UH9000S Manuale utente

Uniden

Uniden UH078SX-NB Manuale utente

Uniden

Uniden UH7700NB Manuale utente

Uniden

Uniden UH9080 Manuale utente

Uniden

Uniden UH037SX-2NB Manuale utente

Uniden

Uniden UH200 Series Manuale utente

Uniden

Uniden BearTracker 885 Manuale utente

Uniden

Uniden UH9000 Manuale utente

Manuali Ricetrasmettitore popolari di altre marche

Yaesu

Yaesu FT-7B Manuale utente

Kenwood

Kenwood ProTalk TK-3201 Manuale utente

Texas Instruments

Texas Instruments TLK10232 Manuale utente

Mizuho

Mizuho MX-2 Guida del prodotto

Kenwood

Kenwood TK-3180 Manuale operativo e di manutenzione

Blitz

Blitz MJ-398U Manuale utente

Utilicom

Utilicom LongRanger 2050 Manuale utente

Standart

Standart HX290UKA Manuale utente

Altronix

Altronix Pace1PTM Manuale utente

Kirisun

Kirisun PT2208 Manuale utente

ELECRAFT

ELECRAFT KX2 Manuale utente

Zodiac

Zodiac K3 Manuale utente

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuale utente

Kenwood

Kenwood TK-2217 Manuale utente

Siemens

Siemens PSO 4000 Manuale utente

Kenwood

Kenwood TS-590SG Manuale utente

Midland

Midland G8E-BT Manuale

ComNav

ComNav Mariner X2 Manuale utente