Unit UT501 Manuale utente
1
UT501/UT502 OPERATING MANUAL
Table of Contents
Title Page
Introduction
Unpacking the Meter
Safety Information
International Electrical Symbols
The Meter Structure
Key Functions
Rotary Switch
Measurement Operation
A. Measuring Voltages
B. Measuring Insulation Resistance
4
4
6
11
12
14
15
16
16
18
2
UT501/UT502 OPERATING MANUAL
Maintenance
A. General Service
B. Replacing the Battery
Specifications
Safety and Compliances
Physical Specifications
General Specifications
Feature Summary
Detailed Accuracy Specifications
A. Voltage Measurement
B. UT501: Insulation Resistance Measurement
UT502: Insulation Resistance Measurement
21
21
23
25
25
26
27
27
28
28
29
30
3
UT501/UT502 OPERATING MANUAL
List of Tables
Table Title Page
1. Unpacking Inspection
2. International Electrical Symbols
3. Meter Front Description
4. Key Description
5. Rotary Switch Description
List of Figures
Figure Title Page
1. The Meter Front Structure
2. Voltages Measurement
3. Insulation Resistance Measurement
4. Battery Replacement
5
11
13
14
15
12
16
18
23
4
UT501/UT502 OPERATING MANUAL
Introduction
Uni-Trend Model UT501 and UT502 insulation resistance tester (hereafter, "the Meter")
is a handheld instrument designed primarily to make resistance/ insulation resistance,
DC/AC Voltage measurement.
Unpacking the Meter
The Meter includes the following items:
5
UT501/UT502 OPERATING MANUAL
Table 1. Unpacking Inspection
Description
English Operating Manual
Test Lead
Test probe
Alligator clip
Carry bag
Strap
1.5V Battery (LR14)
Item
1
2
3
4
5
6
5
Qty
1 piece
1 set
1 set
1 set
1 piece
1 piece
6 pieces
In the event you find any missing or damage, please contact your dealer immediately.
6
UT501/UT502 OPERATING MANUAL
Safety Information
This Meter complies with the standards IEC61010 -1 safety measurement requirement:
in pollution degree 2, overvoltage category (CAT. III 600V, CAT.II 1000V) and double
insulation.
CAT II: Local level, appliance, portable equipment etc., with smaller transient voltage
overvoltages than CAT. III
CAT III: Distribution level, fixed installation, with smaller transient over voltages than
CAT. IV
Use the Meter only as specified in this operating manual, otherwise the protection
provided by the Meter may be impaired.
7
UT501/UT502 OPERATING MANUAL
Danger identifies conditions and actions that pose hazard(s) to the user.
Warning identifies avoiding electric shock.
Caution identifies conditions and actions that may damage the Meter and carrying
out accurate measurement.
International electrical symbols used on the Meter and in this Operating Manual are
explained on page 11.
8
UT501/UT502 OPERATING MANUAL
Danger
Use of instrument in a manual not specifed by the manufactuer may impair
safety features/protection provided by the equipment. Read the following safety
information carefully before using or servicing the instrument.
Do not apply more than 1000V DC or 750V AC.
Do not use the Meter around explosive gas, vapor or dust.
Do not use the Meter in a wet environment.
When using the test leads, keep your figures away from the lead contacts.
Keep your figures behind the finger guards on the leads.
Do not use the Meter with any parts or cover removed.
When carrying out insulation measurement, do not contact the circuit
under test.
9
UT501/UT502 OPERATING MANUAL
Warning
Do not use the Meter if it is damaged or metal part is exposed. Look for
cracks or missing plastic.
Be careful when working above 30V rms, 46.7V ac rms and 70V DC. Such
voltages pose a shock hazard.
Do not change battery when the Meter is in wet environment.
Place test leads in proper input terminals. Make sure all the test leads
are firmly connected to the Meterís input terminals.
Make sure the Meter is turned off when opening the battery compartment.
Carefully read the operating manual before operating the Meter.
Follow the operating manual all the time when using the Meter and keep
the operating manual in a safe place.
Wrong operation will cause incident and damage to the Meter.
10
UT501/UT502 OPERATING MANUAL
Caution
When performing resistance tests, remove all power from the circuit to
be measured and discharge all the power.
When servicing the Meter, use only the same model number or identical
electrical specifications of test leads and power adaptor.
Do not use the Meter if the battery indicator ( ) shows a battery
empty condition. Take the battery out from the Meter if it is not used
for a long time.
Do not use or store the Meter in an environment of high temperature,
humidity, explosive, inflammable and strong magnetic field. The
performance of the Meter may deteriorate after dampened.
Altri manuali per UT501
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Unit Multimetro
Unit
Unit UT71B Manuale utente
Unit
Unit UT212 Manuale utente
Unit
Unit UT131A Manuale utente
Unit
Unit UT801 Manuale utente
Unit
Unit UT58D Manuale utente
Unit
Unit UT204A Manuale utente
Unit
Unit UT39A Manuale utente
Unit
Unit UT70C Manuale utente
Unit
Unit UT30B Manuale utente
Unit
Unit UT 61+ Series Manuale utente
Manuali Multimetro popolari di altre marche
Gossen MetraWatt
Gossen MetraWatt METRAmax 6 Manuale utente
PeakTech
PeakTech 4000 Manuale per l'uso e la cura
YOKOGAWA
YOKOGAWA 90050B Manuale utente
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 Manuale utente
Fluke
Fluke 8846A Manuale operativo e di manutenzione
Tempo Communications
Tempo Communications MM200 Manuale utente
