Unitech MS912+ Manuale utente
MS912+ Wireless
Pocket 2D Scanner
Quick Guide
Version 1.0
For more detailed scanner setting,
please go to www.ute.com to
download the user manual and scanner
configuration manager utility.
- 1--2-
OUT OF THE BOX
Quick Connection Card
Wrist Lanyard
INTRODUCTION
SPECIFICATIONS
Sensor 640 x 480
Resolution 5mil (1D) / 10mil (2D)
PCS 30%
Memory 2MB
Indicator LED, Buzzer
Housing Plastic (PC+ABS)
Profile BT HID, BT SPP
Battery Life 5000 scans
Charge Time 2 hours (fully charged)
Radio Bluetooth 5.0 (Class2)
Coverage 20M/66ft. (line of sight)
Symbologies All major 1D & 2D barcodes
Quick Guide
USB Charger Cable
MS912 Wireless
Pocket 2D Scanner
Quick Guide
NUMERIC BARCODES
1
*1*
2
*2*
3
*3*
4
*4*
5
*5*
Wireless Pocket
2D Scanner
3.
LED Indicator
1. Type-C USB port 4.
Exit Window
2.
Trigger
5. Hard
Reset Button
(insert pin into the hole)
- 3--4-
CHARGING THE BATTERY
1. Flip open the Type-C USB port on the scanner.
2. Insert the Type-C USB connector into the port on the
scanner and USB A connector into a USB port on
the host PC or a smartphone charger.
BEEPER INDICATION
LED INDICATION
Single long beep Power up
Single beep Good read
Single short beep The scanner reads a Code39 of
ASCII in configuration procedure
Two beeps i. Wireless connection
ii. The scanner successfully reads
a configuration barcode
Two short beeps Good read (Batch mode/Memory mode)
Several short beeps The scanner switches from one
communication mode to another
Off
Flashing Green
One Green Flash
Flashing Red
Solid Red
Standby or Power off
Disconnected or Discoverable
Good Read
Low power
Charging
GETTING STARTED
To scan a barcode, make sure the aiming beam fully
covers the barcode.
Four beeps (Hi-Lo-Hi-Lo) Out of range/Poor connection
Five beeps Low power
Three beeps Wireless disconnection
Three short beeps i. The scanner reads a barcodes
while disconnected.
ii. The scanner reads an unexpected
barcode during configuration
procedure. (scan [ABORT] to abort
and start over)
USB A
Host Scanner
Type C
- 5--6-
INTERFACE
There are 5 interfaces for data transmission/collection:
1. BT HID - Emulates a Bluetooth HID keyboard that transmits
each barcode data to the host after decode.
(See page 7)
2. BT SPP - Emulates a Bluetooth SPP device that transmits
each barcode data to the host after decode.
(See page 7)
3. Memory Mode - Emulates a USB mass storage device
that saves each barcode data during
off-line data collection (See page 24)
4. USB HID - Emulates a USB keyboard that transmits each
barcode data to the host after decode.
5. USB VCP - Emulates a USB virtual com device that
transmit each barcode data to the host after
decode.
INTERFACE
. C006$
USB VCP
. C008$
USB HID
Memory Mode
BT SPP
. C035$
BT HID
*Note: For Ez Utility(PC-based software utility), please contact your local
distributor.
FuncƟon Support Matrix
Mode Interface Batch Mode Memory Mode Ez UƟlity
USB HID
USB VCP
BT HID
Wireless
Tethered
BT SPP
Memory
. E042$
. E043$
- 7--8-
GETTING CONNECTED PINCODE SETUP
1. Press the trigger for 1 second to activate the scanner.
2. Scan [DISCONNECT]
3. Scan [BT mode - SPP]
4. Select “Wireless Scanner” from discovered device list.
If pincode is requested, enter default pincode “1234”.
5. Open serial communication software with com port
properly set up.
6. The scanner will beep twice to verify the connection.
There are two modes of wireless communication:
. E042$
BT mode - SPP
Pincode Start
. E032$
. E033$
. E043$
BT mode - HID
Disconnect
. E031$
$TX
1. Press the trigger for 1 second to activate the scanner.
2. Scan [DISCONNECT]
3. Scan [BT mode - HID]
4. Select “Wireless Scanner” from discovered device list.
5. If the Bluetooth application request to enter pincode,
please refer to PINCODE SETUP section on the next page.
6. The scanner will beep twice to verify the connection.
Scan numeric barcodes (see NUMERIC BARCODES section
on the next pages) based on the pincode generated
by the Bluetooth application.
STEP 1
Pincode Stop
Enter
STEP 4
STEP 3
STEP 2
[ Recommended ]
- 9--10 -
NUMERIC BARCODES
1
2
3
4
5
6
7
8
9
0
- 11 --12 -
SMARTPHONE/TABLET TOUCH KEYBOARD
Touch Keyboard - Android
Touch Keyboard - iOS
While connected with the scanner, the Touch Keyboard on the
Android smartphone or tablet might disappear. To resolve this
issue, please change settings on Android device with below steps:
1. Enter “Settings”
2. Enter “Language & input”
4. Turn off “Physical keyboard”, or Turn on “On-screen keyboard”
and the Touch Keyboard will function properly again.
3. Tap on “Default keyboard”
After enabling iOS Hotkey(enabled by default), you may simply
double-click the trigger to toggle the iPhone/iPad Touch Keyboard.
. E047$
ENABLE iOS HOTKEY
Slide to
turn off
SMARTPHONE/TABLET CONNECTION
Getting Connected - iOS & Android
1. Press the trigger for 1 second to power up the scanner.
2. Scan below configuration barcode to clear last pairing record.
3. Scan below configuration barcode to switch to BT HID profile.
. E043$
BT mode - HID
4. Select “Wireless Scanner” from discovered device list.
5. The scanner will beep twice to verify the connection.
Disconnect
. E031$
Tap to
connect
Variable Timeout
No Timeout (Scanner Always On)
POWER OFF TIMEOUT
. B030$
SET MINUTE
. B029$
SET SECOND
. B021$
DISABLE
TIMEOUT
The default timeout is 3 minutes 0 second.
For example, to set the timeout as 5 minutes 30 seconds:
1. Scan [Set Minute]
2. Scan [0] & [5] on page 9 & 10.
(Range: 00 ~60)
(Range: 00 ~60)
3. Scan [Set Minute]
4. Scan [Set Second]
5. Scan [3] & [0] on page 9 & 10.
6. Scan [Set Second]
The period of inactivity before auto power-off.
- 13 --14 -
Once enabled, a checksum will be added to the end of each data
to conduct Xor calculation. For Bluetooth SPP & USB-VCP, the BCC
is 1 byte. For Bluetooth HID, the BCC are 2 bytes.
Example:
The barcode data is “TEST” with terminator <CR><LF>
1. Bluetooth SPP & USB-VCP:
Data Format = <T> + <E> + <S> + <T> + <CR> + <LF> + <BCC>.
BCC = 54h ^ 45h ^ 53h ^ 54h ^ 0Dh ^ 0Ah = 11h
2. Bluetooth HID & USB-HID:
Data Format = <T> + <E> + <S> + <T> + <Enter> + <BCC>
BCC = 54h ^ 45h ^ 53h ^ 54h ^ E7h = F1h
However, since control character cannot be displayed in
Bluetooth HID, BCC will be converted into 2 bytes of characters.
As a result, the data will be: TEST + <Enter> + F + 1
BINARY CHECK CHARACTER
. E030$
. E029$
DISABLE
ENABLE
GENERAL SETTINGS
BEEP MODE
. P023$
. A007$
. F023$
ABORT
CHECK
VERSION
MUTE
. F024$
READING MODE
. F002$
TRIGGER
AUTO-SENSING
CONTINUOUS
. F007$
. F005$
. A001$
DEFAULT
NORMAL
- 15 --16 -
KEYBOARD LAYOUT
. C010$
ENGLISH
(USA)
. C018$
ENGLISH
(UK)
. C011$
GERMAN
. C012$
FRENCH
. C013$
SPANISH
. C014$
ITALIAN
. C009$
JAPAN
(106 key)
CANADIAN
(TRADITIONAL)
. C034$
NORWEGIAN
. C029$
SWEDISH
. C026$
PORTUGUESE
. C031$
CANADIAN
(FRENCH)
. C025$
- 17 --18 -
Altri manuali per MS912+
4
Indice
Altri manuali Unitech Lettore di codici a barre
Unitech
Unitech MS650BT Manuale utente
Unitech
Unitech MS652 Manuale utente
Unitech
Unitech MS912 Manuale utente
Unitech
Unitech MS650 Manuale utente
Unitech
Unitech MS340 Manuale utente
Unitech
Unitech MS838B Manuale utente
Unitech
Unitech ShuttleC Foglio di istruzioni
Unitech
Unitech MS852N Manuale utente
Unitech
Unitech MS912 Manuale utente
Unitech
Unitech MS842N Manuale utente
Unitech
Unitech MS340 Manuale utente
Unitech
Unitech MS962 Manuale utente
Unitech
Unitech MS926 Manuale utente
Unitech
Unitech MS920 Manuale utente
Unitech
Unitech MS852B Plus Manuale utente
Unitech
Unitech MS851B Manuale utente
Unitech
Unitech MS842P Manuale utente
Unitech
Unitech MS320 Manuale utente
Unitech
Unitech MS146 Manuale utente
Unitech
Unitech MS842P Manuale utente
Manuali Lettore di codici a barre popolari di altre marche
POSMicro
POSMicro Datalogic PowerScan D7100 Manuale utente
Marson
Marson MT780 Guida rapida alla configurazione
NCR
NCR RealPOS Manuale utente
Motorola
Motorola SE3300 Guida rapida alla configurazione
Element
Element P130BT Manuale utente
Motorola
Motorola Symbol LS3008 Manuale di installazione e funzionamento
