Unitronics Jazz JZ10-11-R16L Manuale utente

Unitronics 1

Jazz™ OPLC ™ Micro-OPLC Installation Guide

JZ10-11-R16L

6 Digital, 2 Analog/Digital, 2 Analog Inputs, 6 Relay Outputs

Before using this product, the user must read and understand this document.

For additional information regarding this product, refer to the user guide and technical specifications.

All examples and diagrams are intended to aid understanding, and do not guarantee operation.

Unitronics accepts no responsibility for actual use of this product based on these examples.

Please dispose of this product according to local and national standards and regulations.

Only qualified service personnel should open this device or carry out repairs.

Failure to comply with appropriate safety guidelines can cause severe injury or property damage.

Do not attempt to use this device with parameters that exceed permissible levels.

To avoid damaging the system, do not connect/disconnect the device when power is on.

Environmental Considerations

Do not install in areas with: excessive or conductive dust, corrosive or flammable gas,

moisture or rain, excessive heat, regular impact shocks or excessive vibration.

Ventilation: 10mm space required between the OPLCs’ top/bottom edges & enclosure walls.

Do not place in water or let water leak onto the unit.

Do not allow debris to fall inside the unit during installation.

Mounting

Dimensions

85.7mm(3.374")

113.7 mm (4.476")

13.2 mm (0.52")

16.8 mm (0.661")

46.6 mm (1.835")

4 mm (0.157")

7.5 mm (0.295")

12 mm (0.472")

147.5 mm (5.807")

117 mm (4.606")

Add-on modules

Take into account that installing an add-on module requires sufficient clearance space.

During installation After installation

72 mm (2.835")

27.5 mm

(1.083")

38mm

(1.496")

35.8mm

(1.409")

9/12

2 Unitronics

DIN-rail mounting

Snap PLC onto the DIN rail

Panel mounting

Cut-out: 117 x 89mm (WxH)

4.606”x 3.504”

35 mm

(1.378")

53 mm

(2.087")

Gasket

Panel

5mm (max)

0.197" (max)

Wiring

Note: All diagrams are based on the rear view of the OPLC.

Do not touch live wires.

Install an external circuit breaker. Guard against short-circuiting in external wiring.

Use appropriate circuit protection devices.

Unused pins should not be connected. Ignoring this directive may damage the device.

Double-check all wiring before turning on the power supply.

To avoid damaging the wire, do not exceed a maximum torque of 0.5 N·m (5 kgf·cm).

Do not use tin, solder, or any substance on stripped wire that might cause the wire strand to break.

Install at maximum distance from high-voltage cables and power equipment.

Use crimp terminals for wiring; use 26-12 AWG wire (0.13 mm

–3.31 mm

1. Strip the wire to a length of 7±0.5mm (0.250-0.300 inches).

2. Unscrew the terminal to its widest position before inserting a wire.

3. Insert the wire completely into the terminal to ensure a proper connection.

4. Tighten enough to keep the wire from pulling free.

Input or output cables should not be run through the same multi-core cable or share the same wire.

Allow for voltage drop and noise interference with input lines used over an extended distance. Use

wire that is properly sized for the load.

nputs

This model comprises a total of 10 inputs in 3 groups.

1. I0 to I5 are digital inputs. They may be wired, in a group, as either npn or pnp.

2. I6 and I7 may be wired as either digital or analog inputs. These may be wired as either:

npn digital inputs

pnp digital inputs

analog (voltage) inputs

In addition, 1 input may be wired as a pnp input, while the other is wired as an analog input.

Note that if 1 input is wired as an npn input, the other may not be wired as an analog input.

3. AN0 and AN1 are analog (voltage) inputs.

JZ10-11-R16L, 9/12

Unitronics 3

I/O Configuration

Digital Inputs, Controller’s Power Supply

Note: The inputs are arranged in two groups. You can wire one group as npn and the other as

pnp,or wire both groups as npn, or as pnp. In either case, the npn/pnp pins must be connected.

Input wiring (I0-I5), npn (sink) Input wiring (I0-I5), pnp (source)

Input wiring (I6-I7), npn (sink) Input wiring (I6-I7), pnp (source)

Digital Outputs

Output wiring

9/12

Increasing contact life span

To increase the life span of your contacts and protect the unit from potential damage by reverse-

EMF, connect:

A clamping diode in parallel with each inductive DC load

An RC snubber circuit in parallel with each inductive AC load

Analog inputs

Note: Shields should be connected at the signal source.

Analog Input wiring, current

2 or 3-wire, AN0 and AN1 4-wire, AN0 and AN1

Analog Input wiring, voltage

Note: If either I6 or I7 is wired as an npn digital input, the remaining input may not be wired as an

analog input.

JZ10-11-R16/V, AN2 and AN3 JZ10-11-R16V, AN0 and AN1

Samara

tel. +7 846 273 95 85

[email protected]

Yekaterinburg

tel. +7 343 287 19 19

yekat[email protected]

St. Petersburg

tel. +7 812 327 3752

[email protected]

Moscow

tel. +7 495 641 1616

[email protected]

Helsinki

tel. +358 9 540 4940

automation@klinkmann.

Vilnius

tel. +370 5 215 1646

[email protected]

Riga

tel. +371 6738 1617

[email protected]

Мinsk

tel. +375 17 200 0876

[email protected]

Tallinn

tel. +372 668 4500

[email protected]

Кiev

tel. +38 044 495 33 40

[email protected].ua

Indice

Altri manuali Unitronics Controllori

Unitronics

Unitronics M90 OPLC Manuale utente

Unitronics

Unitronics Vision V120 Manuale utente

Unitronics

Unitronics MJ20-MEM1 Manuale utente

Unitronics

Unitronics V130-33-TR6 Manuale utente

Unitronics

Unitronics Vision OPLC V1040-T20B Manuale utente

Unitronics

Unitronics Vision V130-J Series Manuale utente

Unitronics

Unitronics Vision OPLC V570-57-C30B Manuale utente

Unitronics

Unitronics Samba OPLC SM43-J-R20 Manuale utente

Unitronics

Unitronics Jazz OPLC JZ20-T40 Manuale utente

Unitronics

Unitronics Vision OPLC V130-33-TA24 Manuale utente

Unitronics

Unitronics Vision V130-J-TA24 Manuale utente

Unitronics

Unitronics Jazz JZ20-UA24 Manuale utente

Unitronics

Unitronics Vision OPLC V560-T25B Manuale utente

Unitronics

Unitronics US5-B5-RA28 Manuale utente

Unitronics

Unitronics UniStream PLC Series Manuale utente

Unitronics

Unitronics UniStream Manuale utente

Unitronics

Unitronics M91-19-R1 Manuale utente

Unitronics

Unitronics Vision OPLC V130-J-TR20 Manuale utente

Unitronics

Unitronics Vision OPLC V130-33-T38 Manuale utente

Unitronics

Unitronics Vision OPLC V130 Manuale utente

Unitronics

Unitronics UniStream Built-in Series Manuale utente

Unitronics

Unitronics MJ20-MEM1 Manuale utente

Unitronics

Unitronics Samba OPLC SM43-J-R20 Manuale utente

Unitronics

Unitronics Vision V130-T2 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente