Uplift Desk ACC301 Manuale utente

View™ Monitor Arm Instructions

ACC301

There are two ways to attach your UPLIFT View™ Monitor Arm to your desktop: Clamp and Bolt-thru assembly.

Clamp Step 2

Apply the arm gasket (part 2) under the arm’s mount, and the clamp

gaskets (part 5) to the bottom clamp (part 6).

Clamp Step 1

Connect the top clamp (part 3) to the Adapt View™ arm assembly using

the three M6x12mm screws (part C) and the small Allen wrench (part G).

Clamp Step 3

Connect the bottom clamp assembly (part 6) by using M6x10mm (part D)

and the small Allen wrench (part H). Afx the Clamp gaskets as shown.

Clamp Step 4

Turn the knobs counterclockwise to loosen them.

Slide the assembly onto your desk and turn the knobs clockwise

to tighten the clamp to the desk. Make sure that the clamp is secure.

If the clamp is too loose, the unit may wobble or fall.

Snap the cable cover to the back.

Part 1

UPLIFT View™ arm

Part 4

Cable Cover

Part 3

Top Clamp

Part 7

Bolt top clamp

Part 2

Arm gasket

Part 8

Bolt

Part 5

Clamp Gasket

Part 9

Bolt gasket

Part 6

Bottom Clamp

Part 10

Bolt bottom clamp

Part 11

Bolt knob

Part A

M4x12mm screws

(qty 4)

Part F

Washers

(qty 8)

Part B

M5x12mm screws

(qty 4) Part G

Allen wrench

(small)

Part C

M6x12mm screws

(qty 3) Part H

Allen wrench

(large)

Part D

M6x10mm screws

(qty 2)

Please select the appropriate

mounting holes according

to the thickness of the desk.

Clamp Assembly - Attach the arm to the back of your desk

Screws & Tools

Step 2

Use two washers (part F) and two screws* and screw them in by hand.

*Most monitors will use the M4x12 (part A) screws, but if those seem

loose to you, use the M5x12 (part B).

Step 3

Place the monitor onto the on the open holes on the Vesa plate.

See Fig. 1 for specic placement.

Fig. 1

Fig. 2

Step 4

Using 2 more washers and screws, screw into the lower two holes on the

Vesa mounting plate. (see Fig 2).

When nsihed, tighten up all screws from this step and step 2.

Bolt-Thru Assembly - for holes 8.5mm to 70mm

Bolt-Thru Step 1

Insert the long screw (part 8) into the bolt top clamp (part 7).

Bolt-Thru Step 2

Connect the assembly to the Adapt View™ arm using the three M6x12mm

screws (part C) and the small Allen wrench (part G).

Bolt-Thru Step 3

Place the arm gasket (part 2) under the arm’s mount, then slide the assem-

bly into the bolt on your desk. Place the bolt gasket (part 9) onto the bolt

bottom clamp (part 10) as shown.

Bolt-Thru Step 4

Slide bolt bottom clamp (part 10) onto the bolt, and screw on the bolt-thru

knob (part 11) and tighten, to keep the Adapt View™ arm securely fastened

to the desk. Make sure that the clamp is secure. If the clamp is too loose,

the unit may wobble or fall.

The UPLIFT Adapt View™line allows you to run cables from your tray, down the arm,

and to the back of your desk.

a. Pull the four tabs out of the cable cover on the upper section of the arm

b. Pull up and out on the cable cover on the lower section of the arm

c. Run your cables through the exposed section of the arm. Make sure that there is some

slack in the cables to allow the arm to freely move.

d. Trap the cables under the cable cover on the upper section of the arm and snap it back

into place, and slide the cable cover over the wires in the lower section of the arm

Using Cord Management

a. b.

Moving the arm, and counterbalancing

180°

360°

270°

You can adjust the angle and position of your monitor by simply moving

it to the position you desire. If you nd that after you mount your monitor

that it either lifts or drops, then you need to counterbalance your UPLIFT

Adapt Mobile.

Use the large Allen wrench (part H) to adjust the tension adjustment screw

located at the middle joint of the arm. Turn toward the “-” if your arm will

not adjust to a lower position and turn toward the “+” if your arm will

not adjust to a higher position. When the arm stays in place after you’ve

adjusted it, your UPLIFT Adapt Mobile is properly counterbalanced.

Adapt View™ Monitor Arm

CAUTION

These instructions are a component of the UPLIFT View

™ Monitor Arm

. These instructions are part of the scope of delivery, even if the item is resold.

These instructions are also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published

form without the prior written consent of UPLIFT Desk.

These instructions are subject to United States copyright law.

•

The maximum load capacity of the UPLIFT Adapt

View™monitor arm is 19.8 lbs. Do not overload.

Leave cables slack in the arm assembly to allow the

arm room to adjust.

Secure all clamps and mounts to a stable desktop

NOT A CHILD’S TOY. Children under 12 must be

supervised by an adult while using UPLIFT Adapt

View™.

Failing to follow these assembly instructions

and safety precautions may result in personal injury.

Failing to follow these assembly instructions

and safety precautions voids your warranty

and may result in property damage.

Indice

Altri manuali Uplift Desk Rack e supporto

Uplift Desk

Uplift Desk MON020 Manuale utente

Uplift Desk

Uplift Desk Zilker Dual Monitor Arm Manuale utente

Uplift Desk

Uplift Desk Crestview MON033 Manuale utente

Uplift Desk

Uplift Desk ACC305 Manuale utente

Uplift Desk

Uplift Desk ACC092 Manuale utente

Uplift Desk

Uplift Desk MON001 Manuale utente

Uplift Desk

Uplift Desk Motion-X 6-Pack Rack ACC052 Manuale utente

Uplift Desk

Uplift Desk ACC302 Manuale utente

Uplift Desk

Uplift Desk MON001 Manuale utente

Uplift Desk

Uplift Desk MON020 Manuale utente

Uplift Desk

Uplift Desk MON056 Manuale utente

Uplift Desk

Uplift Desk MON051 Manuale utente

Uplift Desk

Uplift Desk MON052 Manuale utente

Uplift Desk

Uplift Desk STR036 Manuale utente

Uplift Desk

Uplift Desk Crestview MON032 Manuale utente

Uplift Desk

Uplift Desk UPL021 Manuale utente

Uplift Desk

Uplift Desk CPU001 Manuale utente

Uplift Desk

Uplift Desk UPL020 Manuale utente

Uplift Desk

Uplift Desk ACC095 Manuale utente

Uplift Desk

Uplift Desk ACC303 Manuale utente

Uplift Desk

Uplift Desk Crestview MON033 Manuale utente

Uplift Desk

Uplift Desk MON054 Manuale utente

Uplift Desk

Uplift Desk Zilker Single Monitor Arm Manuale utente

Uplift Desk

Uplift Desk ACC304 Manuale utente

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente