Vanco EVSP14VW Manuale utente
Vanco Part Number:
EVSP14VW
1X4 Multi-format
Video Wall Processor
with HDMI® Loop-out
www.vanco1.com • 800.626.6445
1x4MULTI-FORMAT
VIDEO WALL
PROCESSOR
with HDMI® Loop-out
www.vanco1.com 800.626.6445
2
1. Do not expose this unit to water, moisture, or
excessive humidity.
2. Do not install or place this unit in a built-in
cabinet, or other conned space without
adequate ventilation.
3. To prevent risk of electrical shock or re
hazard, due to overheating do not obstruct
unit’s ventilation openings.
4. Do not install near any source of heat,
including other units that may produce heat.
5. Do not place unit near ames.
6. Only clean unit with a dry cloth.
7. Unplug unit during lightening storms or when
not used for an extended period of time. A
surge protector is strongly recommended.
8. Protect the power cord from being walked on
or pinched, particularly at the plugs.
9. Use unit only with accessories specied by
the manufacturer.
10. Refer all servicing to qualied personnel.
CAUTION
HDMI is a very complex technology requiring continuous authentication of the signal and the same
video resolution and audio settings on all electronic equipment in the system. When there are multiple
sources and displays, the video resolution and audio setting on all connected units must be adjusted
to correspond with that of the display having the lowest video and audio capability.
WARNING
DEAR CUSTOMER
Thank you for purchasing this product.
For optimum performance and safety, please
read these instructions carefully before connecting, operating or
adjusting this product. Please keep this manual for future reference.
This product is 100% inspected and tested in the United States to verify
HDMI performance parameters.
www.vanco1.com 800.626.6445 3
INTRODUCTION
The Evolution by Vanco EVSP14VW Multi-Format Video Wall Processor with digital and analog audio-video inputs, integrated
USB media player, analog and digital audio breakouts, and IR, TCP/IP and RS-232 control, allows one video signal across
multiple displays to create a video wall! Out of the box, the EVSP14VW can handle up to four displays, in any conguration, or
with the built in loop-out can be expanded by daisy chaining multiple units together to create an even larger video wall system.
Have four displays in a 2x2 conguration, or line them up vertically or horizontally. The EVSP14VW can even be adjusted for
different size display bezels, and is able to change the orientation of the image on the displays to be viewed horizontal, vertical,
or even upside down for displays with a thinner bezel up top. The EVSP14VW supports Composite, VGA, USB, and HDMI video
inputs. Plug in a USB ash drive or hard drive, and the EVSP14VW will continuously play the content via the built in media
player. There is no need for a computer or source to display digital signage. Control of the unit can be done via IR (remote
included), TCP/IP, and RS-232. For any video wall application, small or large, with customization and control, the EVSP14VW
is a great solution!
FEATURES
1x4 Multi-format Video Wall Processor with HDMI Loop-out
Part # EVSP14VW
• HDMI 1x4 Video Wall Processor with Additional HDMI Loop-out for creating larger video wall solutions
• Multi-format functionality supports CVBS/VGA/HDMI inputs and USB for video, picture and music
playback
• A single unit is capable of creating vertical and horizontal video walls in a number of different
congurations and is able to be cascaded into additional units for even larger video wall systems
• Horizontal and vertical bezel correction
• Supports output resolutions up to 1080p@60Hz
• Supports IR, TCP/IP, and RS232 controls
• Compliant with HDMI1.3a, DVI1.0
• HDCP 1.4
• VGA/USB/CVBS support PCM audio; HDMI supports LPCM, Dolby, and DTS audio formats
• Automatic EDID with outputs able to be scaled to: 1024x768, 1360x768, 1080p, and 720p
• De-interlaced video for improved standard denition content
• Dimensions: 9.8” W x 1.25” H x 4.6” D
www.vanco1.com 800.626.6445
4
SPECIFICATIONS
Video Bandwidth ....................................................... 225MHz/6.75Gbps
Input ports ............................................................... (1) HDMI (Female type), (1) USB,
(1) VGA,(1) CVBS+L/R
Video Resolutions……………………………............... up to 1080p@60Hz
Output ports ............................................................ (5) HDMI (Female type),(1) Coaxial, (2) L/R
HDMI cable distance .................................................. 26ft/8-bit 1080p
USB formats…………………………………………. MPEG, H.264, RM/RMVB movie decode, JPEG, BMP,
PNG Picture decode and MPEG1/2, MP3 audio decode
Audio Formats………………………………… supports PCM audio; HDMI supports LPCM, Dolby, and DTS
audio formats
ESD Protection ......................................................... Human body model: ± 8kV (air-gap discharge); ± 4kV
(contact discharge)v
Power supply............................................................. 12V/2.5A DC (US/EU standards, CE/FCC/UL
certication)
Dimensions (mm)....................................................... 9.8” W x 1.25” H x 4.6” D
Weight ..................................................................... 2.3 lbs
Operating Temperature .............................................. 32 ˚F ~ 104 ˚F / 0˚C ~ 40˚C
Storage Temperature ................................................ -4 ˚F ~ 140 ˚F / -20˚C ~ 60˚C
Relative Humidity ..................................................... 20~90% RH (non-condensing)
Power Consumption ................................................. 7.5 W
PACKAGE CONTENTS
• 1x4 Video Wall Processor
• IR Receiver (RX)
• RS-232 Cable
• IR Remote
• DC 12V/2.5A Power Supply
• Product Manual
www.vanco1.com 800.626.6445 5
PANEL DESCRIPTIONS
1 2 3
5
67
89
4
EDID
The EVSP14VW is equipped with EDID management, however there is no need to adjust any dip switches
or dials, the unit automatically reads the EDID from the display(s) and saves it internally. This feature was
created for the installer in mind, for a plug and play installation!
1. POWER SWITCH: Push button switch that turns the unit ON or OFF
2. POWER LED: Illuminates when the unit is connected to power
3. IR: IR sensor
4. CONTROL:
• TCP/IP: Connect a single Cat5e/6 to a network router or switch
• RS232: Connect the included RS-232 cable to a PC
• IR-EXT: Connect the included IR Receiver (RX) for IR control
5. HDMI OUTPUT PORTS 1-4 W/ LOOP OUT: Connect a HDMI displays such as an HDTV or Projector; LOOP
OUT port can also be used to cascade or daisy-chain to another processor, to create a larger video wall
6. AUDIO OUTPUT: Extracts audio via digital Coaxial or analog 3.5mm output
7. ANALOG SOURCE INPUT: Connect a source such as a Set Top Box, Game Console, or PC; inputs are VGA
w/ audio or composite video
8. DIGITAL SOURCE INPUT: Connect a source such as a Set Top Box, Game Console, PC, or USB for le
playback via media player; inputs are USB or HDMI
9. DC 12V IN: Connect the included power supply to power the unit
www.vanco1.com 800.626.6445
6
REMOTE CONTROL
12
3
5
8
4
6
7
1. POWER BUTTON: Push button switch that turns the unit ON or OFF
2. DISPLAY ROTATE ADJUSTMENT: This button rotates the video image 90 degrees each time clockwise; will
only adjust in 1x2, 1x3, and 1x4 video wall modes
3. SOURCE SELECTION: Select from HDMI, VGA, CV (Composite), or USB for the input source to be
displayed
4. DISPLAY FORMAT ADJUSTMENT:
• Auto button adjusts VGA input for proper format
• Zoom button zooms in on video signal for all inputs
• The arrow, back, and exit buttons are for Media Player control using the USB input
5. AUDIO OUTPUT VOLUME ADJUSTMENT: Adjusts volume for HDMI, Digital Coaxial (COAX), and analog
audio output
6. VIDEO WALL FORMAT ADJUSTMENT: Adjusts the type of video wall format desired. For example, if a 2x2
(two displays on top, two displays on the bottom) is desired, simply press the “2” button in the “H” row,
and then press the “2” button in the “V” row
7. BEZEL ADJUSTMENT: Adjusts for bezel size, simply click on the arrows to shrink or expand a picture
vertically or horizontally to adjust video signal to the displays connected
8. RESOLUTION SELECTION: Select from 1080p, 720p, 1360x768, or 1024x768 video output resolutions;
click on the resolution that displays the best
www.vanco1.com 800.626.6445 7
CONNECTION DIAGRAM
CONNECT AND OPERATE
1. Connect a source such as a PC, Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver,
etc. to any of the analog or digital inputs on the unit. Inputs include analog VGA or composite, and digital
USB or HDMI
2. Connect displays such as an HDTV or HD Projector to the HDMI output(s) of the unit
3. Connect an additional EVSP14VW to the “LOOP OUT” port to add more displays for a larger video wall
setup (OPTIONAL)
4. For power, connect the provided power supply
Router
Computer Computer
DVD/Blu-Ray Player
DVD/Blu-Ray Player
IR TX
HDTV
Video Wall
2.0 Audio
Stereo Amplifier
At this point the display connected should display the source signal connected to the unit. If no signal is being
displayed, check all HDMI cables connected. If a display is having difculty receiving a signal, access the
display’s menu and adjust the resolution (lowest to highest until signal is displayed). A 24 Hz vertical refresh
rate may work better than 60 Hz or higher.
IR EXTENSION
The EVSP14VW can be controlled via IR with the included IR remote control. The front panel of the processor
has an IR sensor that can be pointed to, or as an option, can be hidden and be controlled by the included IR
Receiver (RX).
Simply connect the IR Receiver (RX) into the “IR-EXT” port on the back of the unit. The IR Receiver (RX) pigtail
can be led out to an area where the IR remote control can still reach it line of sight while the main unit is
hidden.
www.vanco1.com 800.626.6445
8
ADDITIONAL VIDEO WALL
CONFIGURATIONS
2x1
3x1
4x1
2x2
The EVSP14VW out of the box can handle up to 4 displays in multiple video wall congurations, including the
following:
www.vanco1.com 800.626.6445 9
ADDITIONAL VIDEO WALL
CONFIGURATIONS
1x2 (H)
1x3 (H)
1x4 (H)
1x2 (V)
1x3 (V)
1x4 (V)
www.vanco1.com 800.626.6445
10
SOFTWARE AND USER INTERFACE
CONTROL VIA RS-232
General Page
The EVSP14VW can be controlled via RS-232, and includes a user interface to do so, simply connect
the included RS-232 cable to a PC running Windows operating system. Windows XP or Windows 7 is
recommended. The software is available to be downloaded from www.vanco1.com, under the “downloads” tab
of the EVSP14VW’s product page:
http://vanco1.com/catalog/HDMI_253/Evolution-1x4-Multi-Format-Video-Wall-Processor-with-HDMI-Loop-
out_1558
Setting the unit up with an IP Address for conrol.
1. Select RS232 COM or TCP mode
2. Select the proper COM of the PC or computer being used to connect to the EVSP14VW
3. Connect/Disconnect the EVSP14VW from the PC or computer
4. Select the proper IP address
5. Connect using the IP address selected
6. Search for an IP address of the EVSP14VW
7. Congure unit IP and MAC address
8. Click to reset to the factory default settings:
• Input source: HDMI
• Output Resolution: 1080p60Hz
• Output mode: HDMI
• Audio Volume: 80
• TV Wall Mode: 1x1
• Bezel correction: X=0,Y=0
Indice
Altri manuali Vanco Convertitore multimediale
Vanco
Vanco HDSP4K12 Istruzioni per l'installazione
Vanco
Vanco Evolution EV4K1014 Manuale utente
Vanco
Vanco 280563 Manuale utente
Vanco
Vanco HDVC1 Manuale utente
Vanco
Vanco 12x3 Multi-Function Switch/Scaler Istruzioni per l'installazione
Vanco
Vanco 280708 Istruzioni per l'installazione
Vanco
Vanco HD4KSC Manuale utente
Vanco
Vanco EVOLUTION EVSP8K22 Manuale utente
Vanco
Vanco RS232-IP Manuale utente
