Vaxcel T0575 Manuale di istruzioni
Cross Bar Unit
X1
Mounting Screw
X2
Wire Connector
X3
Ball Nut
X2
Rubber Pad
X2
AA
BB
CC
DD
EE
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
T0575 / T0576
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Page 1 of 5200313
Hardware Package (
included
):
Important to Know
1. Read all instructions carefully before installation and operation.
2. If you are not familiar with state and local electrical codes, it is
recommended that you consult with a qualified electrician.
3. Before installation, shut off power at the main fuse or circuit
breaker box. Be aware that simply turning off the wall switch is
not sufficient to prevent an electrical shock.
4. This fixture requires a 120 VAC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge, make
sure the grounding wire is securely connected.
7. For general safety and to avoid any possible damage to the
sensor, be sure the power is switched "off" before replacing the
bulb.
8. Compatible with LED dimmable bulb.
Maximum Wattage: 60W Incandescent Bulb or 20W LED
Dimmable Bulb
Work Temperature: -4°F~104°F
Features
1. Energy saving fixture.
2. Use dim-to-full brightness where
dim-illumination is preferred, such as your
front entrance. Use off-to-full brightness
where off/on illumination is preferred, such
as your backyard.
3. When in manual override mode, use wall
switch to keep the light ON till dawn.wn.
Installation Steps
Turn off the power at fuse or circuit box. 2. Attach the tail and pipe cap
through the threaded pipe, then
secure them with the finial.
(Fig.2a)
* Optional Assembly:
(See Fig.2b)
Use suitable tools to unscrew
the coupling from the fixture,
then remove the metal pad from
the exposed threaded pipe and
place the pipe cap over the
exposed threaded pipe before
screwing the finial.
2a
2b
Threaded Pipe
Fixture
Fixture
Tail
Finial
Finial
Pipe Cap
Pipe Cap
Metal Pad
1. Screw one end of the threaded
pipe into the coupling and
secure it with a hex nut. Adjust
the length of the threaded pipe
if necessary.
1
Coupling
Hex Nut
Threaded Pipe
Turn on the power at fuse or circuit box
4. Unscrew the two set screws
from the cover. Attach the
cover to the fixture by aligning
the holes of cover and fixture,
then secure the cover with the
two set screws.
3. Install a 60W bulb
Max. Medium Base Bulb
(not included).
5. Unscrew the two ball nuts
(DD). Remove the two rubber
pads (EE) and the cross bar
unit (AA) from the backplate.
3
Max.60W Bulb
(not included)
4
Set Screw
Fixture
Cover
6. Attach the cross bar unit (AA) to
the outlet box by using two
mounting screws (BB). Adjust the
length of the preinstalled
headless screws if necessary.
Note: Make sure that the
headless screws are lined up
horizontally to make the fixture
level.
AA
BB
Headless Screw
6
8. Attach the backplate of the fixture
to the cross bar unit (AA) by
aligning and inserting the two
headless screws from the cross
bar unit (AA) into the open holes
on the backplate, then place the
two rubber pads (EE) over the
exposed headless screws before
screwing the two ball nuts (DD).
Note: With silicone caulking
compound, caulk completely
around where the backplate meets with the wall
surface to prevent water from seeping into the outlet
box.
8
EE
AA
DD
Headless
Screw
Fixture
Backplate
5
EE
AA
DD
Backplate
CC
7
AA
Green Grounding
Screw
7. Pull out the source wires from
the outlet box. Make wire
connections using wire
connectors (CC) as follows:
• Connect the hot wire (usually
black insulation) from the
fixture to the black wire from
the power source.
Connect the neutral wire
(usually white insulation) from
the fixture to the white wire from the power source.
Attach the fixture grounding wire (usually green
insulation or bare wire) to the cross bar unit (AA) with
the green grounding screw, then connect it to the
house grounding wire with the wire connector (CC).
•
•
Carefully put all of the wires back into the outlet box.
Page 2 of 5200313
FUNCTION AND OPERATION
Off Mode
Auto Mode Manual
Override
Manual Override Operation Diagram
Turn wall switch OFF-ON
in 0.5~3 Seconds
Turn wall switch OFF-ON
in 0.5~3 Seconds
Fig. 4
Choose a mode by sliding the slide switch. The light will turn on immediately when power is applied. Wait for 30 seconds
to allow the sensor to warm up.
1. Test MODE (daytime and nighttime operation.)
• The light will turn to low-level brightness (0~50%).The light will turn to high-level brightness (full brightness) when
motion is detected, and stay on as long as the motion continues. The light will turn to the low-level brightness you
set after 5 seconds when motion is no longer detected.
2. Off MODE (nighttime operation only)
• At dusk, the light stays off and will turn to high-level brightness (full brightness) when motion is detected, and stay on
as long as the motion continues. When the motion stops, the light will stay on for the predetermined time set
(5 ~ 180 seconds), then the light will turn off automatically.
3. Auto MODE (nighttime operation only)
• At dusk, the light will turn to low-level brightness (0~50%). The light will turn to high-level brightness (full brightness)
when motion is detected, and stay on as long as the motion continues. When the motion stops, the light will remain
on for the predetermined time set (5~180 seconds), and then turn to the low-level brightness you set.
• The light will turn off automatically at dawn.
The light will turn on (full brightness) automatically at dusk and turn off automatically at dawn.
4. PC MODE (nighttime operation only)
•
5. Manual Override MODE (nighttime operation only)
• To shift to the manual override mode, set the switch to “Off” or “Auto”
mode. Turn the wall switch “OFF” and then turn it “ON” within 3
seconds. The light will stay on through all night. To restore to the
“Off” or “Auto” mode, turn the wall switch “OFF” and then turn it “ON”
within 3 seconds again. (See Fig.4)
• The light will last for one night only and turn off automatically at dawn.
Note: 1. The low level brightness can be adjusted from 0 to 50% by
rotating “Low level” knob. (See Fig.5)
2. Always keep the wall switch in the “ON” position (including the daytime).
3. Please notice the warm up time is 30 seconds, any operations are invalid during this time.
The Position of Control Panel
Sensor
Lens
Fig.1
Sensor
Lens
Fig.3
Fig.2
View Fig.A
Step 1: Rotate the sensor lens from left side to right side
to show the adjustable knobs and slide switch.
(See Fig.1)
Step 2: Adjust time low level brightness and sensitivity
by knobs and choose the mode you want by
slide switch. (See Fig.2 and Fig A).
Step 3: Restore the sensor lens to original position.
(See Fig.3)
“TIME” Knob
“LOW LEVEL” Knob
“SENS” Knob
Small Screwdriver
(not included)
Slide Switch
TEST
OFF AUTO
PC
TIME LOW LEVEL SENS
Fig.A
Page 3 of 5200313
Customization Options
Shut-off Delay Fig. 5
Test Off Auto PC
Low Level
(View from back of sensor lens)
Time Sens
Mode
1. The Shut-off delay is the length of time that the light will stay in
high-level brightness after motion stops.
2. The Shut-off delay can be adjusted by using the “Time” knob when
the slide switch is set in “Off” or “Auto” mode.
3. The range of shut-off delay is 5 seconds to 3 minutes.
4. Rotate the knob clockwise for increasing the shut-off delay.
5. Rotate the knob counterclockwise for decreasing the shut-off delay.
Sensitivity of Motion Sensor
1. The sensitivity can be adjusted from 5 to 40 feet by using the "Sens" knob. (See Fig.5).
2. Turn the knob clockwise for increase sensitivity.
3. Turn the knob counterclockwise for decrease sensitivity.
The following parts are available for reorder if damaged or missing. Call our toll free at 1-800-482-9235.
Where you install your lantern is important:
Be sure the light is mounted straight on the wall;
otherwise, the detection distance may be limited.
5`
6`
10`
40`
Fig.6 Fig. 7
180˚
Motion
Least sensitivity Most sensitivity
Sensor
Fig. 8
Motion
Assembly Kit
4860MM (1 SET) FOR T0575
4859MM (1 SET) FOR T0576
Spare Parts List:
Set Screw
X2
4860SS For T0575
4859SS For T0576
Glass Panel
X3
10109CS
Finial
X1
4860FF For T0575
4859FF For T0576
Cross Bar Unit
X1
Mounting Screw
X2
Wire Connector
X3
Ball Nut
X2
Rubber Pad
X2
AA
BB
CC
DD
EE
NOTE:
1. The sensitivity of the motion sensor will increase as the
environmental temperature gets colder. For best performance,
gently clean the lens with a soft cloth every 1 or 2 months to
ensure maximum sensitivity.
2. The magnitude of adjustment for sensitivity and time may not be
precisely proportionate to the amount when the knob is turned.
(See Fig.5)
3. When installed at a height of 6.5 feet, at 77 degrees Fahrenheit,
the light will provide a maximum detection distance of 40 feet
and detection range of 180 degrees. (See Fig.6 Fig.7)
4. The sensor will be more sensitive to motion across its
detection path than motion directly towards it. (See Fig.8)
5. To reduce possible nuisances, do not mount the fixture
near a heat source like an air conditioner, vent or furnace
exhaust, or in a direction facing any reflecting object or
other light source.
Page 4 of 5200313
B
C
A
A: 16-3/4"
B: 6-3/8"
C: 6-3/4"
TROUBLESHOOTING
Refer to following information to solve your problems.
Set the slide switch in the test mode for testing.
Night
If the light
isn’t on
SYMPTOM DAY/NIGHT POSSIBLE CAUSE SOLUTION
Day
Slide switch is not set in the test
mode.
Wall switch or circuit breaker is off. Turn on wall switch or circuit breaker.
Test the light bulb on normal working light fixture.
Tighten the light bulb.
Check wire connections.
Relocate fixture away from western facing wall.
Eliminate or turn off other light source, block other
light source from shining onto sensor, or relocate
fixture.
Light bulb may be burned out.
Light bulb is loose.
Incorrect or loose wire connections.
Too much sunlight is shining onto
sensor in the early evening.
Too much light is shining onto
sensor due to another light source,
such as a street lamp or other light
fixture.
The bulb is non-dimmable or the
quality of light bulb is not good.
Use another normal incandescent lamp to confirm
if the light function is normal, otherwise change the
bulb.
The light
comes on for
no apparent
reason
If the light
is blinking Night
Night
Passing cars and reflective objects
interfere with the sensor.
Street or sidewalk traffic is triggering
motion sensor.
False triggering caused by a heat
source, such as a heater, dryer vent,
or heated swimming pool.
Relocate fixture.
Adjust the "Sens" knob to reduce the sensitivity.
Eliminate heat source or relocate fixture.
The fixture may be installed in
shaded area. Only need to relocate fixture.
No corrective action needed.
On cloudy or overcast days, the light
may stay on longer than anticipated.
Still on the manual override mode. Turn off the light, then turn it on after 5 seconds.
False triggering caused by a heat
source, such as a heater, dryer vent,
or heated swimming pool.
Eliminate heat source or relocate fixture.
The switch is not set in any mode. Slide it again to the mode you want.
Day
Night
If the light
stays on
Page 5 of 5200313
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Vaxcel Luce esterna
Vaxcel
Vaxcel T0076 Manuale di istruzioni
Vaxcel
Vaxcel T0130 Manuale di istruzioni
Vaxcel
Vaxcel X0090 Manuale di istruzioni
Vaxcel
Vaxcel T0258 Manuale di istruzioni
Vaxcel
Vaxcel T0172 Manuale di istruzioni
Vaxcel
Vaxcel T0616 Manuale di istruzioni
Vaxcel
Vaxcel T0193 Manuale di istruzioni
Vaxcel
Vaxcel T0435 Manuale di istruzioni
Vaxcel
Vaxcel T0297 Manuale di istruzioni
Vaxcel
Vaxcel T0594 Manuale di istruzioni
Vaxcel
Vaxcel T0468 Manuale di istruzioni
Vaxcel
Vaxcel T0698 Manuale di istruzioni
Vaxcel
Vaxcel T0454 Manuale di istruzioni
Vaxcel
Vaxcel T0702 Manuale di istruzioni
Vaxcel
Vaxcel T0099 Manuale di istruzioni
Vaxcel
Vaxcel T0696 Manuale di istruzioni
Vaxcel
Vaxcel T0396 Manuale di istruzioni
Vaxcel
Vaxcel T0040 Manuale di istruzioni
Vaxcel
Vaxcel T0717 Manuale di istruzioni
Vaxcel
Vaxcel T0389 Manuale di istruzioni
Manuali Luce esterna popolari di altre marche
Lindby
Lindby 9949029 Manuale utente
HEPER
HEPER DOGO Side LW6048.585-US Istruzioni per l'installazione e il funzionamento
HEPER
HEPER LW8034.003-US Istruzioni per l'installazione e il funzionamento
Maretti
Maretti VIBE S 14.6080.04.A Manuale utente
BEGA
BEGA 84 253 Manuale
HEPER
HEPER MINIMO Istruzioni per l'installazione e il funzionamento
LIGMAN
LIGMAN BAMBOO 3 Manuale utente
Maretti
Maretti TUBE CUBE WALL 14.4998.04 Manuale utente
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB Manuale utente
urban ambiance
urban ambiance UQL1273 Manuale utente
TotalPond
TotalPond 52238 Manuale utente
Donner & Blitzen
Donner & Blitzen 0-02661479-2 Manuale utente