Vaxcel T0246 Manuale di istruzioni

160929

Page 1 / 5

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

T0246 / T0247

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. Read and save these instructions.

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

Important to Know

1. Read all instructions carefully before installation and

operation.

2. If you are not familiar with state and local electrical

codes, it is recommended that you consult with a

qualified electrician.

3. Before installation, shut off power at the main fuse or

circuit breaker box. Be aware that simply turning off

the wall switch is not sufficient to prevent an electrical

shock.

4. This fixture requires a 120 VAC, 60 Hz power source.

Maximum wattage light bulb is 60W.

5. Do not attempt to take the lantern apart; there are

no serviceable parts inside.

6. To avoid sensor damage by lightning or electrical

surge, make sure the grounding wire is securely

connected.

7. For general safety and to avoid any possible damage

to the sensor, be sure the power is switched "off"

before replacing the bulb.

Maximum Wattage: 60W

Work Temperature: -40F ~ 1040F

Features

2. Use the dim-to-bright illumination option where

1. Energy saving fixture.

you want some minimum illumination through out

the night, such as at your front entrance or garage

door. Use the dark-to-bright illumination option

where you do not need minimum brightness, such

as the backyard or back porch.

3.When in manual override mode, use wall switch

to keep the light on till dawn.

Hardware Package (included)

Green Grounding

Screw

Mounting Screw

Wire Nut

Lock Nut (D)

Ball Nut

Mounting Plate

Headless Screw

Rubber Pad

160929

Page 2 / 5

Installation Steps

1. Shut off power at the circuit breaker of where the fixture is to be installed.

2. Thread two headless screws through the mounting plate, then secure them with four lock nuts (two on each

side of the mounting plate). Adjust the length of the headless screws if necessary.

3. Attach the mounting plate to the outlet box by using two mounting screws.

4. Unscrew the small bolt nuts and small rubber pads and remove the metal frame from the fixture.

Note: The following step 5 you may install if you desire:

5. Attach the threaded pipe into the bottom hole of metal frame and tighten it with the lock nut. Attach the spider

onto the threaded pipe, then tighten it with the finial.

6. Take a glass panel and gently slide the narrow side of the glass panel down into the metal frame in place,

secure it by pressing the clips from both top and bottom sides. (See Fig.1 & Fig.2) Repeat with other panels.

8. Attach fixture to the wall by aligning headless screws on mounting plate with holes on back plate. Slide

headless screws through holes and secure with two bolt nuts and rubber pads.

9. With silicone caulking compound, caulk completely around where the back plate meets with the wall surface.

Note: Be sure to caulk completely where the back plate meets the wall surface to prevent water

from seeping into the outlet box.

10.Install a bulb (not included). Check relamping label at socket area or packaging for maximum allowed wattage.

11. Attach the metal frame onto the fixture and tighten it with samll bolt nuts and samll rubber pads.

Pull out the wires and grounding wire from the outlet box. Make wire connections using the wire nuts as

follows:

---Connect the hot wire (usually black insulation) from the fixture to the black wire from the power source.

---Connect the neutral wire (usually white insulation) from the fixture to the white wire from the power source.

---Attach the fixture grounding wire (usually green insulation or bare wire) to the mounting plate with the green

grounding screw, and then connect it to the house grounding wire with the wire nut.

Carefully put the wires back into the outlet box.

“L”Clip

Clip

Metal Frame

Those four parts you may install onto the lamp if you desire.

Glass Panel

Threaded Pipe

Lock Nut

Spider

Finial

Fig.1

Fig.2

Mounting plate

House Grounding Wire

Green Grounding Screw

Fixture Grounding Wire

Wire Nut

Outlet Box

Fixture Wire

Back Plate

Mounting Screw

Lock Nut

Headless Screw

Studs

Metal Frame

Bolt Nuts

Small Bolt Nuts

Lens

Small Rubber Pads

Fixture

Glass Panels

Max.60W type A

standard base bulb

(Bulb not included)

Rubber Pad

160929

Page 3 / 5

“3H Mode”

“6H Mode”

“0 Mode”

Manual

Override

Mode

Turn wall switch OFF-ON

in 3 Seconds

Turn wall switch OFF-ON

in 3 Seconds again

(Adjustable low level)

(View from one side of Back plate)

Fig.1 Fig.2

Manual Override Operation Diagram

Function and Operation

MODES OF OPERATION

Choose a mode by sliding the switch on the bottom of the back plate of the fixture. (See Fig.3 ).

When power is first applied, the light will turn to high level brightness, wait for 15 seconds to allow the sensor to warm up.

1. TEST MODE (daytime and nighttime operation)

● The light will turn to low-level brightness (0%~50% brightness). The light will turn to high-level brightness (100%

brightness) when motion is detected, and stay on as long as the motion is continuing. The light will revert to

low-level brightness about 5 seconds after motion is no longer detected.

2. 3H MODE (nighttime operation only)

●At dusk, the light will turn to high-level brightness (100% brightness). The light will turn to low-level brightness (0%

~50% brightness) automatically after 3 hours. The light will turn to high-level brightness (100% brightness) when

motion is detected, and stay on as long as the motion is continuing. When motion is no longer detected, the light

will remain on for the predetermined time you set (5~180 seconds), and then revert to low-level brightness you set.

● Light will turn off automatically at dawn, and return to 3 H mode at dusk.

3. 6H MODE (nighttime operation only)

●At dusk, the light will turn to high-level brightness (100% brightness). The light will turn to low-level brightness (0%

~50% brightness) automatically after 6 hours. The light will turn to high-level brightness (100% brightness) when

motion is detected, and stay on as long as the motion is continuing. When motion is no longer detected, the light

will remain on for the predetermined time you set (5~180 seconds), and then revert to low-level brightness you set

● Light will turn off automatically at dawn, and return to 6 H mode at dusk.

4. 0 MODE (nighttime operation only)

● The light will turn to low level brightness (0%~50% brightness) at dusk. The light will turn to high-level brightness

(100% brightness) when motion is detected, and stay on as long as the motion is continuing. When motion is no

longer detected, the light will remain on for the predetermined time you set (5~180 seconds), and then revert to

low level brightness you set.

● Light will turn off automatically at dawn, and return to 0 H mode at dusk.

5.Manual Override MODE (nighttime operation only; on at dusk,off at dawn)

● In 3, 6 or 0 mode, to shift to manual override mode, turn off the wall switch in 3 seconds and then turn it on again,

the light will turn to high-level brightness at dusk, and turn off automatically at dawn. To return to the previous

settings, turn off the wall switch in 3 seconds and then turn it on again. (See Fig.1)

● The lights will turn off automatically at dawn.

Note:You can adjust the low level brightness (0~50%) by using the slide switch on the side of back plate.

(See Fig.2)

Turn on the power at fuse or circuit box.

Page 4 / 5

(View from Bottom of Back plate)

(Exterior Wall)

TIME SENSITIVITY

TEST 0

3 6

CUSTOMIZATION OPTIONS:

Shut-off Delay

The Shut-off delay is the length of time the light will stay at high-

level brightness after motion has ceased to be detected. This

Shut-off delay can be set when operation is in 3, 6 or 0 Mode by

using the “TIME” knob located on the left side of the panel at the

bottom of the back plate (See Fig.3) . To increase the shut-off

delay, turn the knob clockwise. To decrease shut off delay, turn

the knob counterclockwise. The delay may be adjusted from a minimum of 5 seconds to a maximum of 3 minutes. The

light will stay on as long as motion is detected continuously and will automatically turn to low-level brightness when no

more motion is detected after the delay time has passed.

Sensitivity of Motion Sensor

The sensitivity of the motion sensor can be adjusted by using the “SENSITIVITY” knob located on the right side of the

panel at the bottom of the back plate (See Fig.3). To increase sensitivity, turn the knob clockwise. To decrease

sensitivity, turn the knob counterclockwise. The sensitivity may be adjusted from a minimum of 5 feet to a maximum of

40 feet.

NOTE:

1. The sensitivity of the motion sensor will increase as the

environmental temperature gets cooler. For best

performance, gently clean the lens with a soft cloth every

1 or 2 months to assure maximum sensitivity.

2. For best performance, install fixture at least 6-1/2 feet above

the ground. At such a height, the fixture will provide a

detection distance of up to 35 feet at 77 degrees

Fahrenheit. (See Fig.4)

3. The sensor detects across a detection range of 220 degrees.

(See Fig.5)

4. The sensor will be more sensitive to motion across its

detection path than motion directly towards it. (See Fig.6)

5. To reduce possible nuisances, do not mount the fixture

near a heat source like an air conditioner, vent or furnace

exhaust, or in a direction facing any reflecting object or

other light source.

Where you install your lantern is important:

Be sure the light is mounted straight on the wall;

otherwise, the detection distance may be limited.

Motion

Least sensitive

Motion

Most sensitive

Sensor

Fig.3

Fig.5

Fig.4

Fig.6

160929

8.0'

6.5'

35'

220'

Page 5 / 5

160929

Troubleshooting

---If the light does not work at all:

1. Make sure the wall switch and circuit breaker are on.

2. Make sure the wiring connection is correct.

3. Make sure the bulb is not burned out.

4. Cover the sensor with your palm to verify that the ambient light level is not too high.

----In Test Mode, if the light stays on full brightness after 5 seconds:

1. Check whether the motion is detected at all time.

The following parts are available for re-order if damaged or missing.

Spare Parts List:

Assembly Kit

5533MM(1 SET)

Assembly Kit

5593BB(1 SET)

Glass Panel

9839FE for T0246

9840FE for T0247

T0246

A: 9"

B: 18-3/4"

C: 10-1/4"

T0247

A: 7"

B: 16"

C: 8-1/4"

5-YEAR LIMITED WARRANTY:

All products are warranted to be free of defects in material and workmanship for five (5) years from date of purchase.

This warranty is limited to the correction of any such defect, or the replacement of any such defective item(s), provided

that: (a) we are properly notified and consent to return of the item(s) in question:(b) the item(s) is / are returned with proof

of purchase date; and (c) it is found upon inspection by us that the item(s) is / are defective as noted above. This warranty

does not cover labor costs, consequential damages, nor does it apply to any item(s) that have been improperly installed,

overloaded, altered, or otherwise abused by the customer, its agent(s) or employee(s). Finishes are specially excluded

from the terms of this warranty since they are subject to environmental maintenance deemed beyond our control. Other

than the described obligation, we assume no further liability with respect to the sale or use of our products.We make no

warranty, express or implied, and disclaim any warranty of merchantability or fitness for a particular purpose.

Green Grounding

Screw

----After performing 3H or 6H mode, or in 0 H mode. If the light stays on full brightness after 3 minutes.

1. Make sure no motion could be picked up by the sensor.

2. Make sure that mode entry is not in manual override.

----In PC / Manual override Mode, if the light stays on after dawn:

1. Whether the ambient light level is too low.

----If the light blinks:

1. Make sure the light is not mounted near a barbecue, air conditioner or other heat source.

2. Make sure of using incandescent bulb or dimmable LED bulb.

Mounting Screw

Wire Nut

Lock Nut (D)

Ball Nut

X2 Small Ball Nut with Rubber Pad

Mounting Plate

Headless Screw

Rubber Pad

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Vaxcel Luce esterna

Vaxcel

Vaxcel T0717 Manuale di istruzioni

Vaxcel

Vaxcel T0130 Manuale di istruzioni

Vaxcel

Vaxcel Lambda T0627 Manuale di istruzioni

Vaxcel

Vaxcel T0389 Manuale di istruzioni

Vaxcel

Vaxcel T0517 Manuale di istruzioni

Vaxcel

Vaxcel T0647 Manuale di istruzioni

Vaxcel

Vaxcel T0085 Manuale di istruzioni

Vaxcel

Vaxcel T0414 Manuale di istruzioni

Vaxcel

Vaxcel T0551 Manuale di istruzioni

Vaxcel

Vaxcel T0451 Manuale di istruzioni

Vaxcel

Vaxcel T0571 Manuale di istruzioni

Vaxcel

Vaxcel T0364 Manuale di istruzioni

Vaxcel

Vaxcel T0258 Manuale di istruzioni

Vaxcel

Vaxcel T0616 Manuale di istruzioni

Vaxcel

Vaxcel T0594 Manuale di istruzioni

Vaxcel

Vaxcel T0595 Manuale di istruzioni

Vaxcel

Vaxcel T0541 Manuale di istruzioni

Vaxcel

Vaxcel T0362 Manuale di istruzioni

Vaxcel

Vaxcel T0165 Manuale di istruzioni

Vaxcel

Vaxcel T0449 Manuale di istruzioni

Vaxcel

Vaxcel T0692 Manuale di istruzioni

Vaxcel

Vaxcel T0080 Manuale di istruzioni

Vaxcel

Vaxcel Mission T0437 Manuale di istruzioni

Vaxcel

Vaxcel T0692 Manuale di istruzioni

Manuali Luce esterna popolari di altre marche

Sealey

Sealey LED37 Manuale utente

nordlux

nordlux VEJERS Guida utente

SImx

SImx ELITE LED LHTC637 Manuale utente

GEV

GEV CAROLINE 10833 Manuale utente

NEBO

NEBO NEB-LSP-0020 Manuale utente

WE-EF

WE-EF PFL540 LED Manuale utente

Lindby

Lindby 9949029 Manuale utente

HEPER

HEPER DOGO Side LW6048.585-US Istruzioni per l'installazione e il funzionamento

HEPER

HEPER LW8034.003-US Istruzioni per l'installazione e il funzionamento

Maretti

Maretti VIBE S 14.6080.04.A Manuale utente

BEGA

BEGA 84 253 Manuale

HEPER

HEPER MINIMO Istruzioni per l'installazione e il funzionamento

LIGMAN

LIGMAN BAMBOO 3 Manuale utente

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manuale utente

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manuale utente

urban ambiance

urban ambiance UQL1273 Manuale utente

TotalPond

TotalPond 52238 Manuale utente

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manuale utente