Velleman K4001 Manuale utente
2
3
Features:
This small amplifier is constructed around the TDA2003 IC, capable of delivering 4Wrms at 4ohms. The IC is completely
thermally and short-circuit protected. A conventional direct current can be connected as supply.
Specifications :
Music output power : 7W/4ohm
RMS output power : 3.5W/4ohm or 2W/8ohm
Total harmonic distortion : 0.05% (1W/1KHz)
Frequency response : 20Hz-20KHz (-3dB)
Input sensitivity : 40mV/150Kohm
Signal/noise ratio : 86dB (A weighted)
Power supply : 8-18VDC/0.5A
Dimensions : 55x35mm (2.2” x 1.4”)
Features & Specifications
4
Assembly hints
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
• A good quality soldering iron (25-40W) with a small tip.
• Wipe it oftenon a wet sponge or cloth, to keep it clean; then apply solder to the tip, togive it a wet look. This is called ‘thinning’ and will
protect the tip, and enables you to make goodconnections. When solder rolls off the tip, it needs cleaning.
• Thin raisin-core solder. Do not use any flux or grease.
• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they
cannot fly towards the eyes.
• Needle nose pliers, for bending leads, or to hold components in place.
• Small blade and Phillips screwdrivers. A basic range is fine.
For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
⇒ Make sure the skill level matches your experience, to avoid disappointments.
⇒ Follow the instructions carefully. Read and understand the entire step before you perform each operation.
⇒ Perform the assembly in the correct order as stated in this manual
⇒ Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
⇒ Values on the circuit diagram are subject to changes.
⇒ Values in this assembly guide are correct*
⇒ Use the check-boxes to mark your progress.
⇒ Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.
0.000
5
Assembly hints
1.3 Soldering Hints :
1- Mount the component against the PCB surface and carefully solder the leads
2- Make sure the solder joints are cone-shaped and shiny
3- Trim excess leads as close as possible to the solder joint
REMOVE THEM FROM THE TAPE ONE AT A TIME !
AXIAL COMPONENTS ARE TAPED IN THE CORRECT
MOUNTING SEQUENCE !
You will find the colour code for the resistances and the LEDs in the HALG
(general manual) and on our website: http://www.velleman.be/common/service.aspx
6
R1 : 470 (4 - 7 - 1 - B)
R2 : 4,7 (4 - 7 - B - B)
R3 : 100 (1 - 0 - 1 - B)
1. Resistors. R...
Construction
C1 : 8n2 (822)
C2 : 100nF (104)
C3 : 100nF (104)
3. Capacitors.
C4 : 10µF
C5 : 470µF
C6 : 1000µF
C7 : 1000µF
5. Electrolytic Capacitors.
Watch the polarity !
C...
IN
GND
LS
GND
+V
GND
4. PCB tabs
R4 : 1 (1 - 0 - B - B - 9)
2. Metal film resistor.
R...
IC1 : TDA2003!
6. IC.
7
Supply connection
7. Supply connection
Fig. 1.0
Figure 1 is an example of a suitable mains supply for this circuit. Naturally, you can also use batteries to
power the circuit.
FUSE 1A T
FUSEHOLDER
TRANSFORMER
POWER SWITCH 240V 3A
MAINS
STRAIN RELIEF
12V AC 6VA
RECTIFIER BRIDGE
+-
1.5A 50V
ELECTROLYTIC CAPACITOR 2200µF 25V
8
Volume control
Fig. 2.0
47K OHM LOG
GND
Signal IN
TO AMPLIFIER
SHIELDED CABLE
POTENTIOMETER
FROM SOURCE
GND
SIGNAL (+)
Adjust the volume by connecting a 47K logarithmic potentiometer as indicated in figure 2.0.
8. Volume control
9
Connection example
Figure 3.0 is an example of a connection diagram of a 4 or 8 ohm speaker that is connected to the pins LS
and GND. The input signal should be connected with the IN and GND pins.
9. Connection example
4/8 OHM SPEAKER
+
-
8..18VDC / 0.5A
47K LOG POTENTIOMETER
+
-
-
+
FROM AUDIO SOURCE
Fig. 3.0
10
10. PCB layout.
PCB
Indice
Altri manuali Velleman Amplificatore
Velleman
Velleman HQ Power VPA2100U1 Manuale utente
Velleman
Velleman POWER BLOCK K8081 Manuale utente
Velleman
Velleman HQ Power PAA01 Manuale utente
Velleman
Velleman K4102 Manuale utente
Velleman
Velleman K8084 Manuale utente
Velleman
Velleman VM113 Manuale utente
Velleman
Velleman High-Q K2572 Manuale utente
Velleman
Velleman K4005B Manuale utente
Velleman
Velleman HQ-Power VDSPROM7 Manuale utente
Velleman
Velleman High-Q Velleman-kit K8022 Manuale utente
Velleman
Velleman ARDUINO VMA408 Manuale utente
Velleman
Velleman HQ-POWER SAGIRA 100 Manuale utente
Velleman
Velleman 8021 Manuale utente
Velleman
Velleman HQ-Power ANTM7 Manuale utente
Velleman
Velleman K1803 Manuale utente
Velleman
Velleman K8021 Manuale utente
Velleman
Velleman VPA2100M Manuale utente
Velleman
Velleman 8020 Manuale utente
Velleman
Velleman HQ Power ONELINER 100 Manuale utente
Velleman
Velleman K8066 Manuale utente
