Velleman K2639 Manuale utente
LIQUID LEVEL CONTROLLER
K2639
ILLUSTRATED ASSEMBLY MANUAL H2639IP-1
Total solder points: 129
Difficulty level: beginner 12345 advanced
Forgottentoturnoffthetap,leakingwashing
machines,...Preventionisbetterthancure.So
usethisfluiddetector.Thismultifunctional
deviceiseasytouseinavarietyofapplications.
2
SPECIFICATIONS:
• Power supply: 12-14VAC or 16-18VDC / 100mA
• Relay output: 240V / 3A max.
• Dimensions:
Controller PCB: 104 x 60mm (4.1" x 2.4")
Sensor PCB: 104 x 25mm (4.1" x 1.0")
Recommended transformer: ordernr. 207004
Recommended adapter: ordernr. PS1203
Introduction & Specifications
Did you forget to turn off the tap? Is the washing machine leaking? Will the aquarium level fall too low? Has
the rain water tank overflowed? Do you have water in the cellar? Just a minor mishap, or a disaster! You can
avoid all this by installing the liquid level controller in the right way and in the right place.
Level indicator : three LED's are used to indicate “LOW LEVEL”, “MEDIUM LEVEL”and “HIGH LEVEL”.
Level controller : the relay automatically switches a pump and/or valve on and off to keep the level
between “LOW”and “HIGH”.
Alarm : an “alarm”signal is available to indicate “wet”or “dry”. Some applications may demand a siren (e.g.
KIT K2604), or perhaps a bell or a lamp may be more suitable.
It is possible to replace the liquid sensors with other sensors, e.g. temperature or light dependent resistors
(NTC/LDR) and thus use the device as a temperature/light controller.
3
Assembly hints
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
• A good quality soldering iron (25-40W) with a small tip.
• Wipe it oftenon a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’and will
protect the tip, and enables you to make goodconnections. When solder rolls off the tip, it needs cleaning.
• Thin raisin-core solder. Do not use any flux or grease.
• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they
cannot fly towards the eyes.
• Needle nose pliers, for bending leads, or to hold components in place.
• Small blade and Phillips screwdrivers. A basic range is fine.
For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
⇒ Make sure the skill level matches your experience, to avoid disappointments.
⇒ Follow the instructions carefully. Read and understand the entire step before you perform each operation.
⇒ Perform the assembly in the correct order as stated in this manual
⇒ Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
⇒ Values on the circuit diagram are subject to changes.
⇒ Values in this assembly guide are correct*
⇒ Use the check-boxes to mark your progress.
⇒ Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual updates,indicated as ‘NOTE’on a separate leaflet.
0
.0
0
0
4
Assembly hints
1.3 Soldering Hints :
1- Mount the component against the PCB surface and carefully solder the leads
2- Make sure the solder joints are cone-shaped and shiny
3- Trim excess leads as close as possible to the solder joint
REMOVE THEM FROM THE TAPE ONE AT A TIME !
AXIAL COMPONENTS ARE TAPED IN THE
CORRECT MOUNTING SEQUENCE !
You will find the colour code for the resistances and the LEDs on our website:
http://www.velleman.be/common/service.aspx
5
R8 : 47K (4 - 7 - 3 - B)
R9 : 47K (4 - 7 - 3 - B)
R10 : 47K (4 - 7 - 3 - B)
R11 : 47K (4 - 7 - 3 - B)
R12 : 680 (6 - 8 - 1 - B)
R13 : 680 (6 - 8 - 1 - B)
R14 : 680 (6 - 8 - 1 - B)
R15 : 680 (6 - 8 - 1 - B)
R16 : 68K (6 - 8 - 3 - B)
R17 : 68K (6 - 8 - 3 - B)
R18 : 4K7 (4 - 7 - 2 - B)
R19 : 4K7 (4 - 7 - 2 - B)
R20 : 4K7 (4 - 7 - 2 - B)
R21 : 12K (1 - 2 - 3 - B)
R22 : 1M (1 - 0 - 5 - B)
3. Resistors
IC1 : 14p
5. IC socket, Watch the po-
sition of the
Construction
J : 2x
1. Jumpers
D1 : 1N4148
D2 : 1N4148
D3 : 1N4148
D4 : 1N4148
D5 : 1N4148
D6 : 1N4007
2. Diodes. Check the polarity!
D...
CATHODE
R1 : 1M (1 - 0 - 5 - B)
R2 : 47K (4 - 7 - 3 - B)
R3 : 47K (4 - 7 - 3 - B)
R4 : 47K (4 - 7 - 3 - B)
R5 : 47K (4 - 7 - 3 - B)
R6 : 47K (4 - 7 - 3 - B)
R7 : 47K (4 - 7 - 3 - B)
R...
C1 : 100nF (104)
C2 : 100nF (104)
C3 : 100nF (104)
C4 : 100nF (104)
C5 : 100nF (104)
C6 : 100nF (104)
4. Capacitors
C7 : 100nF (104)
C8 : 100nF (104)
T1 : BC547B
6. Transistor
LD1 : 5mm red
LD2 : 5mm yellow
LD3 : 5mm green
LD4 : 5mm red
7. LEDs. Watch the polarity !
COLOR= 2...5
LD...
CATHODE
LD.
LD1 : High level
LD2 : Medium level
LD3 : Low level
LD4 : Relay activated
6
Fit four terminal pins
between marks S1 and
S2. You may also use
screw connectors.
Fit 6 terminal pins for the relay
output (NO, C , NS) and the
power supply (AC IN). You
may also use screw
connectors.
Fit 4 terminal pins to the holes
A, B, C and D
9. PCB pins
Construction
C11 : 22nF
8. Capacitor
C9 : 10µ F / 25V
10. Electrolytic capacitor.
Watch the polarity !
C...
VR1 : UA7812
Check the orientation !
11. Voltage regulator
VR...
C10 : 1000µ F / 35V
12. Electrolytic capacitor.
Watch the polarity !
C...
RY1 : VR15M121C 12V / 15A
13. Relay
RY...
IC1: LM324
Pay attention to the position
of the notch!
14. IC mounting
PIN 1
1
7
Inspect the completed board thoroughly before connecting a power supply.
When applying a DC voltage (16 to 18V/100 mA) :
The positive input should go to the pin nearest “AC IN”, the negative input
to the second pin (Fig 1.0).
For connecting a transformer (12 to 14V/min 300 mA):
The connection sequence isn’t important (Fig 2.0).
15. Testing
Testing
NO
C
VR1
NC
ACin
ACin
-
+
ADAPTER
(16-18VDC/100mA)
Fig 1.0
NO
C
VR1
NC
ACin
ACin
L
N120 - 230 VAC
2x 7.5VAC
300mA
Fig 2.0
8
With power on, LD3 (LOW LEVEL) should illuminate, showing that
everything works.
Put a link across low-level sensor S2, and LD2 should illuminate.
Add another link across high-level sensor S1, and LD1 and LD4 should
both illuminate.
Remove the link across input sensor S1, now LD2 should illuminate
together with LD4 (relay on).
Remove the link across input sensor S2, now only LD3 should illuminate.
Testing
LD4
S1
LD1
LD2
LD3
S2
LD4
S1
LD1
LD2
LD3
S2
LD4
S1
LD1
LD2
LD3
S2
LD4
S1
LD1
LD2
LD3
S2
Fig 3.0
Fig 3.1
Fig 3.2
Fig 3.3
9
For application as controller/indicator and alarm, 1 or 2 sensors must be connected. A sensor consists of 2
separated electric conductors : 2 metal strips on a PCB or a jack plug etc. There are 2 sensors on the sensor
PCB : S1 (HIGH LEVEL) and S2 (LOW LEVEL).
Cut a piece of your sensor PCB when the difference in height between S1 and S2 is too high for your application
(Fig 4.0).
On the contrary, if the levels are too close, lengthen S2 by soldering two un-insulated wires to the copper
traces (Fig 5.0).
16. Applications
Applications
Unisolated wire Solder
Fig 5.0
Fig 4.0
10
Applications
A dry sensor behaves like an electric isolator. When the sensor is wet the resistance drops to some Kilo-Ohms
maximum. The electrical resistance of a sensor depends on the conductivity of the liquid, spacing between the
electrodes, and the wet areas of the electrodes. The specific conductivity of some liquids is so high that this
controller can’t detect them. Sometimes the problem may be solved by increasing the surface of the electrodes. To
avoid electrolysis or deposits on the sensor strips, the sensing voltage is alternating with a frequency around 1KHz.
INDICATOR / CONTROLLER
Connect both sensors.
ATTENTION : Place sensor S1 higher than sensor S2
NEVER USE sensors in an INFLAMMABLE ENVIRONMENT: when the sensors get dry
small sparks can occur which are able to ignite pockets of gas with a resultant
explosion. In a chemical environment (acids...) metal electrodes can erode. It may be
necessary to construct the electrodes of an inert metal e.g. inox.
S1
S2
LIQUID LEVEL
CONTROLLER
S2
S1
S1
S2
Indice
Altri manuali Velleman Controllori
Velleman
Velleman K8088 Manuale utente
Velleman
Velleman HQ-Power VDPDMXC146 Manuale utente
Velleman
Velleman TRCV2A Manuale utente
Velleman
Velleman High-Q Velleman-kit K6000 Manuale utente
Velleman
Velleman VM192RF Manuale utente
Velleman
Velleman VM162 Manuale utente
Velleman
Velleman AER Domus Guida all'installazione
Velleman
Velleman SOL30UC2 Manuale utente
Velleman
Velleman HQ POWER VDPDMXC144 Manuale utente
Velleman
Velleman HQ Power VDPC130 Manuale utente
Velleman
Velleman CHLSC2 Manuale utente
Velleman
Velleman TRCV3 Manuale utente
Velleman
Velleman CAMCOLD/CK Manuale utente
Velleman
Velleman VDP100TT Manuale utente
Velleman
Velleman HQ Power VDPDMXC136 Manuale utente
Velleman
Velleman E305DC Manuale utente
Velleman
Velleman HQ Power VDPDMXC174 Manuale utente
Velleman
Velleman HQ POWER VDPC174 Manuale utente
Velleman
Velleman vellight CHLSC4 Manuale utente
Velleman
Velleman VMB2BL Manuale utente
