Velleman High-Q-kit K8051 Manuale utente

15 Channel IR remote stick

K8051

ILLUSTRATED ASSEMBLY MANUAL H8051IP-1

Total solder points: 66

Difficulty level: beginner 12345 advanced

Sleekdesignerenclosurewithjust2

buttons,yetitprovidesaccestoa

stunning15channels.

Features:

 Slim designer enclosure.

 2-button operation.

 Built-in ‘all clear’ function

 3 addresses with 15 channels each.

 Easy channel and address selection.

 Compatible with most current and upcoming IR kits.

 Low power consumption.

Specifications:

• Power supply : 2 x AAA battery (not included).

• Dimensions : 160x27x23mm / 6,3x1x0,9”

• Range : up to 20m (K8050 / indoors)

Features & Specifications

Assembly hints

1. Assembly (Skipping this can lead to troubles ! )

Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.

1.1 Make sure you have the right tools:

• A good quality soldering iron (25-40W) with a small tip.

• Wipe it oftenon a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will

protect the tip, and enables you to make goodconnections. When solderrollsoff the tip,it needs cleaning.

• Thin raisin-core solder. Do not use any flux or grease.

• A diagonal cutter to trim excess wires. To avoid injury whencutting excess leads, hold the lead so they

cannot fly towards the eyes.

• Needle nose pliers, for bending leads, or to hold components in place.

• Small blade and Phillips screwdrivers. A basic range is fine.

For some projects, a basic multi-meter is required, or might be handy

1.2 Assembly Hints :

⇒ Make sure the skill level matches your experience, to avoid disappointments.

⇒ Follow the instructions carefully. Read and understand the entire step before you perform each operation.

⇒ Perform the assembly in the correct order as stated in this manual

⇒ Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.

⇒ Values on the circuit diagram are subject to changes.

⇒ Values in this assembly guide are correct*

⇒ Use the check-boxes to mark your progress.

⇒ Please read the included information on safety and customer service

* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.

0.000

Assembly hints

1.3 Soldering Hints :

1- Mount the component against the PCB surface and carefully solder the leads

2- Make sure the solder joints are cone-shaped and shiny

3- Trim excess leads as close as possible to the solder joint

REMOVE THEM FROM THE TAPE ONE AT A TIME !

AXIAL COMPONENTS ARE TAPED IN THE COR-

RECT MOUNTING SEQUENCE !

 R1 : 4E7 (4-7-B-B)

 R2 : 330 (3-3-1-B)

 R3 : 330 (3-3-1-B)

 R4 : 330 (3-3-1-B)

 R5 : 330 (3-3-1-B)

 R6 : 330 (3-3-1-B)

 R7 : 330 (3-3-1-B)

 R8 : 330 (3-3-1-B)

 R9 : 47K (4-7-3-B)

 R10 : 47K (4-7-3-B)

1. Resistors

R...

Construction

 C1 : 100nF (104, u1)

2. Capacitor

 SW1 : Transmit (KRS1243)

3. Push button

 IC1: 14p

4. IC socket, Watch the po-

sition of the notch!

 T1 : BC639

5. Transistor

Place the IC SVK8051 (Programmed

PIC16F630-I/P) into its socket

 Pay attention to the position of

the notch!

6. IC mounting

PIN 1

Construction

7. Mounting the LED readout

1. Stick a piece of tape over the LED mounting holes. This allows

you to level the LEDs before soldering them.(see fig. 1.0).

Complete the assembly as follows :

2. Insert the LEDs BUT DO NOT SOLDER THEM YET!

Mind the polarity ! (fig 2.0)

FIG 1.0

FIG 2.0

CATHODE

 LD1

 LD2

 LD3

 LD4

 LD5

 LD6

MIND THE POLARITY !

3. Flip the PCB and guide all LEDs trough their holes (fig 3.0).

=> Make sure that all LEDs touch the tape!

4. Solder the connections (fig 4.0).

5. Remove the tape.

Construction

FIG 3.0

FIG 4.0

2 Holes must be drilled into the enclosure.

 Follow next steps exactly!

 Pay attention to the correct diameter.

Make sure the holes are free of burrs.

STEP 1

Drawing 5.0 provides a drill pattern for the ‘select’ button.

• Mark the centre of the hole with a pencil.

• Drill the hole using a 3.5mm drill.

FIG 5.0

10mm

Enclosure preparation

8. Enclosure preparation

Enclosure preparation

STEP 2

Drawing 7.0 provides a drill pattern for the IR-LED.

• Close the enclosure with the 2 supplied screws. Mark the centre of the hole to be drilled on the top of the

enclosure (Fig 6.0). Make sure that the centre of the hole is in the middle of the housing and 7mm from

the left hand side (Fig 7.0)

• Drill the hole with a 5,5mm drill.

 Make sure the edges of the holes are completely smooth!

Dia 5.5

7mm

FIG 6.0 FIG 7.0

TOP

BOTTOM

STEP 1

Mount the ‘select’ push button. (SW2)

Mounting the PCB

9. Mounting the PCB

Altri manuali per High-Q-kit K8051

Indice

Altri manuali Velleman Telecomando

Velleman

Velleman luxibel LX302 Manuale utente

Velleman

Velleman VM152 Manuale utente

Velleman

Velleman VRC1001 Manuale utente

Velleman

Velleman High-Q-kit K8051 Manuale utente

Velleman

Velleman VRC1601D Manuale utente

Velleman

Velleman MK160 Manuale utente

Velleman

Velleman VRC801D Manuale utente

Velleman

Velleman VRC801 Manuale utente

Velleman

Velleman CAMCOLVC19 Manuale utente

Velleman

Velleman MML16C Manuale utente

Velleman

Velleman VM130 Manuale utente

Velleman

Velleman IREXT Manuale utente

Velleman

Velleman VM130V2SET Istruzioni per l'installazione

Velleman

Velleman VM118R Manuale utente

Velleman

Velleman vm118 Manuale utente

Velleman

Velleman VM109 Manuale utente

Velleman

Velleman HAMGSM133 Manuale utente

Velleman

Velleman VM130T Manuale utente

Velleman

Velleman VM130 Manuale utente

Velleman

Velleman HIGH-Q Manuale utente

Velleman

Velleman K6501 Manuale utente

Velleman

Velleman CTC1000RC Manuale utente

Velleman

Velleman CAMB29 Manuale utente

Velleman

Velleman High-Q Velleman-kit K8023 Manuale utente

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione