Velleman PEREL WLC003 Manuale utente
WLC003
V. 01 –17/06/2020 2 ©Velleman nv
WLC003
V. 01 –17/06/2020 3 ©Velleman nv
WLC003
V. 01 –17/06/2020 4 ©Velleman nv
USER MANUAL
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that
disposal of the device after its lifecycle could harm the
environment. Do not dispose of the unit (or batteries) as
unsorted municipal waste; it should be taken to a
specialized company for recycling. This device should be
returned to your distributor or to a local recycling service.
Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Perel! Please read the manual thoroughly
before bringing this device into service. If the device was damaged in
transit, don't install or use it and contact your dealer.
2. Safety Instructions
Read and understand this manual and all safety signs
before using this appliance.
•This device can be used by children aged from 8 years and above,
and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given
supervision or instruction concerning the use of the device in a
safe way and understand the hazards involved. Children shall not
play with the device. Cleaning and user maintenance shall not be
made by children without supervision.
•This device is intended only for recording digital photos and
videos, particularly for observing wildlife. It is not intended for
any other use or for uses extending beyond those stated. This
device is not intended for use in commercial or industrial
environments.
WLC003
V. 01 –17/06/2020 5 ©Velleman nv
•When used outdoors, bad weather conditions or rapid changes in
the weather could lead to errors in recording or faulty images.
•Insert the memory card before powering on the camera. The
camera has no internal memory for saving images or videos and
will not work if there is no memory card installed.
•Unlock the write protection before inserting the memory card.
•Do not insert or take out the memory card when the camera is
switched on.
•It is recommended to format the memory card when used for the
first time. Many memory cards formatted by other cameras have
poor compatibility with different brands of cameras.
•When setting up the camera, allow approximately 10 to 20
seconds for the camera to acquire a signal.
•In setup the camera will shut down automatically after 3 minutes
if no operation is done. Please turn on the power again to re-
activate the camera.
3. General Guidelines
•Refer to the Velleman®Service and Quality Warranty on
www.velleman.eu.
•All modifications of the device are forbidden for safety reasons.
Damage caused by user modifications to the device is not covered
by the warranty.
•Only use the device for its intended purpose. Using the device in
an unauthorised way will void the warranty.
•Damage caused by disregard of certain guidelines in this manual
is not covered by the warranty and the dealer will not accept
responsibility for any ensuing defects or problems.
•Nor Velleman nv nor its dealers can be held responsible for any
damage (extraordinary, incidental or indirect) –of any nature
(financial, physical…) arising from the possession, use or failure
of this product.
•Keep this manual for future reference.
WLC003
V. 01 –17/06/2020 6 ©Velleman nv
4. Overview
Refer to the illustrations on page 2 of this manual.
Camera
1
display
10
speaker
2
menu
11
card slot
3
playback
12
AV jack
4
left
13
USB jack
5
up/video
14
mode
6
down/capture
15
IR LEDs
7
right
16
lens
8
shot
17
front sensor
9
OK
18
lateral sensor
Tripod
1
screw
5
hex screw
2
locking nut
6
wall plugs
3
pivot bolts
7
screws
4
drill holes
5. Installation
5.1 Mounting on Concrete
1. Choose an appropriate installation location:
oEnsure that there are no electric lines, water or heating pipes
installed at the proposed drilling location.
oThe supplied wall plugs are only suitable for mounting on
concrete and stone. Before starting the installation, please
check your installation location carefully for its suitability for
the plugs.
oThe recommended installation height is between 1 and 2 m
above the ground.
oThe assembly material used must be suitable for the
respective location. If in doubt, consult a professional.
2. Mark the drill holes using the wall bracket.
3. Use a drill with a 6 mm drill bit to drill the required holes. Insert
the wall plugs flush with the wall.
WLC003
V. 01 –17/06/2020 7 ©Velleman nv
4. Screw the wall bracket to the wall using the supplied screws.
5. Mount the camera on the tripod screw. Turn the camera in the
desired direction and lock it with the lock nut.
6. To align the camera into its final position, undo the two pivot bolts
a little, align the camera and fix the position by tightening the
two pivot bolts (see below for more information).
5.2 Alternate Mounting
Use the included mounting belt to fix the camera around a tree trunk.
5.3 Powering
WARNING –Do not puncture batteries or throw them
in fire as they may explode. Do not attempt to
recharge non-rechargeable batteries (alkaline).
Dispose of batteries in accordance with local
regulations. Keep batteries away from children.
•Open the camera and remove the battery cover. Install the
batteries following to the correct polarity.
•If the camera is low on power, please connect the camera to a
power adapter (not included, see technical specifications).
5.4 Inserting the Memory Card
Install the memory card before switching on the
camera.
Unlock the write protection and insert a formatted memory card into
the card slot. Do not force to avoid damaging the card. We
recommend using a TF card, class 6 or higher, max. 32 GB.
At first use, wait for the memory card to reach ambient temperature.
Therefore, the camera may present some delay.
To avoid damage, protect memory card from water, strong vibrations,
dust, hot sources and direct sunlight.
Note that, if the memory card is full, the camera will stop recording
automatically and the LEDs will go out.
WLC003
V. 01 –17/06/2020 8 ©Velleman nv
5.5 Peripheral Connection
You can allow the camera to transfer the video signal to an external
monitor or a television.
1. Connect the camera to a monitor using the included AV cable.
2. Switch on the monitor and set it to AV mode.
3. Switch on the camera and proceed to test the system.
4. Once connection is successful, the camera will enter playback
mode and the screen turns black. The image will be shown on the
monitor.
6. Operation
6.1 System Setup and Test
1. Slide the mode switch to the TEST position.
2. Press video or capture to switch between these two modes.
3. Press menu to enter or to exit the setup menu.
4. Press up or down to navigate through the menu or options, and
press OK to confirm.
6.2 Aligning the Camera
Set the optimum exposure angle on the camera. Consider whether the
use of the lateral motion sensors may be useful for attaining the
desired observation results. You can activate or deactivate these
sensors at all times.
1. After having installed the camera, switch on the camera and
move slowly from one side of the target area to the other. While
doing this, monitor the motion display.
2. If the LEDs turn blue, you are detected by one of the activated
lateral sensors. If the LEDs red, you are detected by the front
motion sensor. By this way you can align the camera to the best
angle and distance.
WLC003
V. 01 –17/06/2020 9 ©Velleman nv
6.3 Basic Working Mode
Slide the switch to the on position. After 15 seconds the camera will
enter the standby mode.
When a motion is detected, the camera take photos or record video
automatically according to the settings.
6.4 Basic Settings
Mode
Slide the mode switch to the on position and select the working mode.
In capture mode, the camera will take pictures only. In video mode,
the camera will record. In capture + video mode, the camera will take
a picture first and then record.
Options: Photo →Video →Photo & Video
Photo Resolution
Set the still image resolution.
Options: 16MP →12MP →8MP →5MP →3MP
Photo Series
Set the number of continuous photo capturing. In photo mode, the
camera will take photos continuously.
Options: 1 photo →2 photos in series →3 photos in series
Video Resolution
Set the video resolution. The bigger the resolution, the longer the
video which can be stored.
Options: 1920x1080P →1280x720P →720x480P →640x480P →
320x240P
TL Video Resolution
Set the time-lapse video resolution.
Options: 2592x1944P →2048x1536P
Video Length
Set the recording duration of a video clip.
Options: 3 s to 10 min
WLC003
V. 01 –17/06/2020 10 ©Velleman nv
Audio Recording
Select this option to add audio to a video.
Options: On →Off
Shot Lag
Set the recording delay time after the motion detection. Within the
selected time, the camera will not record any image or video.
Options: 5 s to 60 min
IR Distance
Set the distance of IR induction.
Options: Near →Middle →Far
Side Motion Sensors
Switch the lateral motion sensors on or off.
Options: On →Off
Motion Sensor Sensitivity
Set the sensitivity of the sensors.
Recording environment
Recommended setting
indoor
low
outdoor, normal conditions
middle
outdoor, difficult conditions
high
outdoor, low temperatures
low
outdoor, mild temperatures
high
Options: Low →Middle →High
Target Recording Time
When setting a target recording time, the camera will only record in
the set time slot.
Options: On →Off
Indice
Lingue:
Altri manuali Velleman Telecamera da ricognizione
