Ventrac HP720 Manuale utente
MOWER
MODEL HM600/HM720/HP720
REVISED 06-26-06
09.10013
OWNER/OPERATOR’S
MANUAL & PARTS LIST
Venture Products Inc. Orrville, OH
ii
TO THE OWNER
Congratulations on the purchase of a new VENTRAC Mower! The purpose of this
manual is to assist you in its safe and effective operation and maintenance.
With proper usage and care, the Mower will provide many years of service. Please read
and understand this manual entirely before using the Mower. Keep this manual on file
for future reference.
Always give Model and Serial # when ordering service parts.
Please fill in the following information for future reference:
Date of Purchase: Month _________________ Day __________ Year _______________
Model Number: ___________________________________________________________
Serial Number: ___________________________________________________________
Dealer: _________________________________________________________________
Dealer Address: __________________________________________________________
__________________________________________________________
Dealer Phone Number: _____________________________________________________
Dealer FAX Number: ______________________________________________________
Venture Products Inc. reserves the right to make changes in design or
specifications without incurring obligation to make like changes on
previously manufactured products.
Orrville, OH
www.ventrac.com
TABLE OF CONTENTS
INTRODUCTION Section A
Description .....................................A-1
Specifications ...................................A-2
SAFETY Section B
Safety Symbols ..................................B-1
Decals .......................................B-2
General Safety Procedures ............................B-3
Safety Operation & Techniques ..........................B-4
OPERATION Section C
Attaching......................................C-1
Detaching .....................................C-1
Operating Techniques & Tips .........................C-1&2
Mulching Kit ....................................C-3
MAINTENANCE Section D
Lubrication .....................................D-1
Removal & Reinstallation of Blades ......................D-1&2
Deck Belt Replacement ............................D-2&3
(HM600 Ser# AA1001-AA1357) (HM720 Ser# AA1001-AA1188) (HP720 Ser# AA1001-AA1066)
Deck Belt Replacement (HM600 Ser# AA1358--) (HM720 Ser# AA1189--) (HP720 Ser# AA1067--)......D-3&4
Drive Belt Replacement ..............................D-4
Mower Tire Pressure................................D-4
Deck Leveling Procedure ...........................D-4&5
Storage ......................................D-5
Sharpening Blades ................................D-5
iii
TABLE OF CONTENTS
PARTS & ILLUSTRATED DRAWINGS Section E
Figure 1 - Deck ..................................E-12
(HM600 Ser# AA1001-AA1262) ( HM720 Ser# AA1001-AA1134) (HP720 Ser# AA1001-AA1025)
Figure 2 - Deck .................................................E-3&4
(HM600 Ser# AA1263-AA1945) (HM720 Ser# AA1135-AA1612) (HP720 Ser# AA1026-AA1180)
Figure 3 - Deck ................................E-5&6
(HM600 Ser# AB1946--) (HM720 Ser# AB1613--) (HP720 Ser# AB1181--)
Figure4-Spindle Assembly..........................E-7&8
(HM600 Ser# AB1946--) (HM720 Ser# AB1613--) (HP720 Ser# AB1181--)
Figure 5 - Carrier Frame ...........................E-9&10
(HM600 Ser# AA1001-AA1262) (HM720 Ser# AA1001-AA1134) (HP720 Ser# AA1001-AA1025)
Figure 6 - Carrier Frame ....................................E-11 & 12
(HM600 Ser# AA1263--) (HM720 Ser# AA1135--) (HP720 Ser# AA1026--)
Figure 7 - Caster & Rear Roller .......................E-13 & 14
Figure 8 - Hitch Assembly .........................E-15 & 16
(HM600 Ser# AA1001-AA1357) (HM720 Ser# AA1001-AA1188) (HP720 Ser# AA1001-AA1066)
Figure 9 - Hitch Assembly ...................................E-17 & 18
(HM600 Ser# AA1358--) (HM720 Ser# AA1189) (HP720 Ser# AA1067)
WARRANTY
iiii
INTRODUCTION
Product Description
The VENTRAC HM600, HM720 and HP720 mowers have a cutting width of approx. 60”
and 72” respectively. The “uni-body” design creates a lightweight, heavy-duty, and high
performance deck plus a streamlined carrier frame. With the removal of two pins
beneath the cross frame, the deck can be tilted to a near vertical position for cleaning
and servicing. The top side of the deck is designed to eliminate trapped grass, dirt and
water.
Four carrier points, two adjustable connecting links and one cross shaft comprise the
complete mechanism for controlling the cutting height. A single handle with a slight
outward pull allows an easy quick change in cutting height selection. A slide release
allows the handle to be returned to the deck level to prevent it from catching on low
branches and shrubs.
These mowers, with near full width rear rollers and large, pneumatic, front swivel caster
tires, are designed to float over the terrain independent of the tractor. The traction
transfer system on the VENTRAC 4000 series tractor reduces mower weight on the
ground, decreases the steering effort, and increases the traction of the tractor.
These attractive two-tone, smooth styled mowers with a high performance discharge
tunnel, offer an unusual combination of efficiency, effectiveness and end results.
Careful, proper, and safe operation of tractor and mower will result in a great mowing
job.
The model HP720 provides a 6-1/2” offset of the mower to the left side. The mower still
has a centered appearance because of the right side discharge chute. The offset
creates a better “reach” on the left side of the deck for mowing under low tree branches,
fences, or over the edge of ditches and water.
A-1
INTRODUCTION
Ventrac HM600 Specifications
Cutting Width ...................... Approx. 60 inches
Overall Width ........................... 70inches
Length ............................... 52inches
Height ............................... 16inches
Approx. cutting height ................1-3/4 to 4-3/4 inches
Weight .............................. 366pounds
Ventrac HM720 Specifications
Cutting Width ...................... Approx. 72 inches
Overall Width ........................... 82inches
Length ............................... 58inches
Height ............................... 16inches
Approx. cutting height ................1-3/4 to 4-3/4 inches
Weight .............................. 435pounds
Ventrac HP720 Specifications
Cutting Width ...................... Approx. 72 inches
Overall Width ........................... 82inches
Length ............................... 58inches
Height ............................... 16inches
Approx. cutting height ................1-3/4 to 4-3/4 inches
Weight .............................. 435pounds
Offset to the left ........................ 6-1/2 inches
A-2
SAFETY
B-1
ATTENTION:
This symbol identifies potential health and
safety hazards. It marks safety
precautions. Your safety and the safety of
others is involved.
SIGNAL WORD DEFINITIONS
Indicates a potentially hazardous situation
which, if not avoided, may result in minor
or moderate injury and/or property
damage. It may also be used to alert
against unsafe practices.
Indicates a potentially hazardous situation
which, if not avoided, could result in death
or serious injury.
Indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury. This signal word is
limited to the most extreme cases.
SAFETY
B-2
The following decals must be maintained on your Ventrac mower. If any decals are
faded or missing, contact your dealer promptly for replacements.
Decals
A B C
D
E
F
Decal Page &
Location Description Part Number
A E-2,#37 Danger Shield Missing 00.0062
B E-8,#15 Warning Moving Part Hazard 00.0101
C E-8, #3 Danger Pinching Hazard 00.0102
D E-2, #14 Thrown Object Hazard 00.0122
E E-2, #13 Keep Hands and Feet Away 00.0123
F E-2, #39 Ventrac Serial No. Plate N/A
SAFETY
B-3
General Safety Procedures
for Ventrac Tractors, Attachments, & Accessories
Read and understand the operator’s manual before operating this equipment.
Observe and follow all safety decals.
DO NOT let children or any untrained person operate the tractor or attachment.
Make sure that all operators of this equipment are thoroughly trained in using it
safely.
Never allow additional riders on the tractor or attachments.
DO NOT operate tractor or attachments if you are under the influence of alcohol,
drugs, medication that may impair judgment or cause drowsiness, or if you are not
feeling well.
Operate all controls from the operators seat only.
Before operating equipment, make sure all shields are in place and fastened.
Ensure the attachment or accessory is locked or fastened securely to the tractor
(power unit) before operating. See tractor manual for locking procedure.
Ensure that all bystanders are clear of the tractor and attachment before operating.
Be especially careful and observant if other people are present. Never assume that
bystanders will remain where you last saw them.
Always look in the direction the tractor is moving.
Never direct the discharge of any attachment in the direction of people, animals,
buildings, vehicles, or objects of value.
Immediately stop at any sign of equipment failure and correct the problem before
continuing to operate. An unusual noise can be a warning of equipment failure.
Before adjusting, cleaning, lubricating, or changing parts on the tractor or attachment,
engage the parking brake, lower the attachment to the ground, stop the engine, and
remove the ignition key.
To prevent the risk of uncontrolled equipment movement on tractors equipped with 2
speed axles, always shift the transaxle range with the power unit stationary on level
ground and with the parking brake engaged.
If equipment is to be left unattended, engage the parking brake, lower the attachment
to the ground, stop the engine, and remove the ignition key.
SAFETY
B-4
HM600, HM720, and HP720 Safety Procedures
Before mowing, clear the area of stones, sticks, and other foreign objects that can be
thrown by the mower.
Use extra care when mowing around trees, shrubs, and other objects that may block
your vision.
Never mow with the discharge chute flipped up or missing! The hinge feature is
provided only for transport and storage.
Disengage the PTO when you are not mowing.
When mowing on a steep incline, always mow uphill and downhill. Never mow across a
steep incline.
Before making any repairs or adjustments, lower
attachment to the ground, set parking brake, shut
the engine off, and remove the key.
Read and understand the operator’s manual before
operating this equipment.
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Ventrac Taglia erba
Ventrac
Ventrac MR740 Manuale utente
Ventrac
Ventrac LM600 Manuale utente
Ventrac
Ventrac LQ450 Manuale utente
Ventrac
Ventrac MJ840 Manuale utente
Ventrac
Ventrac LM600 Guida all'installazione
Ventrac
Ventrac 4100 Series Manuale del proprietario
Ventrac
Ventrac LQ450 Manuale utente
Ventrac
Ventrac MY560 Manuale utente
Ventrac
Ventrac MT720 Manuale utente
Ventrac
Ventrac HM600 Manuale utente
Ventrac
Ventrac MC600 Manuale utente
Ventrac
Ventrac Ventrac HQ680 Manuale del proprietario
Ventrac
Ventrac Ventrac HQ680 Manuale utente
Ventrac
Ventrac Ventrac HQ680 Manuale utente
Ventrac
Ventrac MK960 Manuale utente
Ventrac
Ventrac MJ840 Manuale utente
Ventrac
Ventrac HM602 Manuale utente
Ventrac
Ventrac MS600 Manuale utente
Manuali Taglia erba popolari di altre marche
TALEN TOOLS
TALEN TOOLS AVR HGM30 Manuale utente
DEWEZE
DEWEZE ATM-725 Manuale operativo
Weed Eater
Weed Eater 180083 Manuale utente
Husqvarna
Husqvarna Poulan Pro PP185A42 Manuale utente
Better Outdoor Products
Better Outdoor Products Quick Series Manuale utente
Cub Cadet
Cub Cadet 23HP Z-Force 60 Manuale operativo
