Vents TRF-220/12-25 Manuale utente
ISOLATION
TRANSFORMER
“VENTS TRF-220/12-25”
PURPOSE
The isolation transformer TRF-220/12-25, called hereinafter " the transformer", is intended for the household
fans power supply of ultra-low secure voltage 12 V / 50 Hz , in which the motor's power does not exceed 16 W.
BASIC TECHNICAL CHARACTERISTICS
Supply voltage 220-240 V, 50 Hz.
Target voltage 12 V, 50 Hz.
Maximal load power, no more 25 WA (load current no more than 2 A).
The transformers belong to devices of the Class II insulation by type of protection against electric-shock
hazard.
Overall dimensions of the transformer, no more 91x58x62 mm.
Overall dimensions of the protective terminal box, no more 110x40x40 mm.
Weight, no more - 0,8 kg.
Protection Class concerning dust and moisture (except for the terminal blocks) IР40.
Transformer operation conditions 100C +400С and relative humidity of no more than 75 %.
The ambient air should contain no explosive and corrosive impurities.
SAFETY REQUIREMENTS
The maintenance and installation should be carried out by the person who has the admission to the
independent work with the electrical installations up to 1000 V and has studied this manual.
Attention! The transformer input circuit is under network potential. The transformer installation and
connection should be made only after its disconnection from the network system..
Forbidden!
- To operate the defective transformer,
- To make alterations to the scheme,
- To transfer the energized transformer,
- To operate the transformer with a damaged isolation of network cable and output cables ,
- To connect and disconnect output cables if the transformer is turned on,
- To overload the transformer electrically.
Not allowed!
- Water ingress in design elements of the transformer,
- No explosive and corrosive impurities should be present in air.
DELIVERY SET
The delivery set contains:
Isolation transformer TRF-220/12-25 ready-assembled with protective terminal box,
- certificate,
- spare safety fuse 0,25 A / 250 V,
- packing box.
ACCEPTANCE CERTIFICATE
The isolation transformer TRF-220/12-25 is recognized to be serviceable
V32EN -01
STORAGE AND TRANSPORTATION
The transformer should be stored in manufacturer packaging in closed and aired room without the acid and
other steams having a harmful effect on the materials and isolation at temperature from +5°С to +40°С and
relative air humidity of no more than 80 % (at Т = 25°С).
The transformer in the manufacturer transport container can be transported by any kind of transport in
covered vehicles.
Transportation of the transformer should be carried out according to the handling stamps on the packaging.
MANUFACTURER'S GUARANTEES
The transformer TRF-220/12-25 corresponds to requirements of GOST 30030-93 (MEK 742-83)
“Isolation Transformers and Safe Isolation Transformers. Technical Requirements ”, DNAOP 0.00-1.32-01”
Rules of the Electrical Installation Structure. Electrical Equipment of the Special Installations ",
" Rules of the Technical Operation of Electrical Installations”.
The manufacturer, Joint-Stock Company "VENTS", guarantees normal work of the transformer for
12 months from the date of sale through the retail trading network provided transportation, storage,
installation and operation rules are complied with. The guarantee does not apply to the products with signs
of the mechanical damages. In case of malfunction in transformer work because of the manufacturer within
The warranty period, the consumer has the right for the transformer replacement. In the absence of sale date
mark, the warranty period is estimated from the date of manufacturing.
Replacement is made under the address:
1, Kotzubinskogo street, 01030, Kiev, Ukraine
Sale date Manufacturing date
SELLER Approval mark
1
TRANSFORMER STRUCTURE
Appearance with the overall and connection dimensions (specified in millimeters) is shown on fig. 1.
For protection against overloads, the transformer has replaceable fuse FUSE integrated in the input terminal
block XT1. For the safety grounds, the terminal block ХТ1 is mounted in the protective terminal box. The output
terminal block ХТ2 serves for connection of the fan with safe supply voltage of 12 V.
INSTALLATION AND OPERATION INSTRUCTIONS
The transformer with terminal box should be installed inside the room in a zone not subject to influence
of the raised humidity.
At that, it is not allowed in the course of installation and operation:
Ingress of splashes, rain drops,
Direct solar light,
Installation near to heating devices, other sources of heat.
The fire safety requirements should be observed during installation and operation.
Connection to the electric power network should be carried out by one of two ways:
By means of an electric cable equipped with the standard plug for connection to the corresponding socket
integrated in the fixed wiring,
Through the switch with contact gaps at least 3 mm on all poles integrated in the fixed wiring.
Regulator connection to the electric power network should be carried out according to schemes shown
on fig. 2, 3, where:
Q1 - the external switch integrated in the fixed wiring,
ХТ1 -input terminal block with the integrated safety fuse in protective terminal box,
XF1 - socket integrated in the fixed wiring,
M1 - standard plug,
Т1 - the transformer,
ХТ2 - output block for connection of the fan with supply voltage of 12 V,
B - fan with supply voltage of 12 V
Transformer, protective terminal box as well as output terminal block and downlead should be reliably fixed
on the basis of an insulation material
(The wood structure is not considered to be a reliable insulator).
The terminal block XT2 should be protected against dust and moisture. It is not allowed, to place and fix the
terminal block XT2 on the conducting basis. If the transformer is placed in a box, the sufficient ventilation
should be provided in order to except its overheat.
TYPICAL MALFUNCTIONS AND METHODS OF THEIR ELIMINATION
The transformer starts to work right after voltage supply on its input. If the device does not work, you should
execute the malfunctions diagnostics, using table 1.
table 1
In order to replace the safety fuse you should:
- Disconnect voltage of the transformer power supply;
- Open the protective terminal box (having unscrewed previously the two screws located on the box cover);
- Take out the safety fuse holder from the terminal block ХТ1 (see fig. 1), replace the safety fuse with
the spare one,
- Put the safety fuse holder into place;
- Close the protective terminal box cover, screw up the 2 screws, connect the power supply voltage.
MALFUNCTION PROBABLE REASON ELIMINATION METHOD
There is no voltage in the network.
The electric contact in the terminal block
clips of the transformer or fan is broken.
The safety fuse has blown because of an
overload or short circuit on the transformer
output.
Fan malfunction.
Check up the network voltage.
At its absence, take measures on
restoration of the network functioning .
Renew the electric connection in the
terminal block clips of the transformer or fan.
Eliminate the reason of the transformer
overload or short circuit on its output.
Replace the safety fuse.
Renew the fan efficiency or replace it.
The fan connected
to the transformer,
does not work.
91
62
42
49
58
45
44
66
Red Yellow
79
XT2 12V~
50Hz
T1
T1
90
110
100
40
2,5
L
N
B
12V ~
XT2
T1
XT1
XF1XM1
220-240V~
50Hz
L
N
T1 B
12V ~
Q1
XT1
220 - 240V~
50Hz
FUSE
28
40
32
figure 1
XT1XT2
220-240V~
50Hz
red yellow
red yellow
red yellow
red yellow
figure 2
figure 3
Altri manuali per TRF-220/12-25
1
Altri manuali Vents Trasformatore
