Verkada TD52 Manuale utente
Document
Document Details
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
V1.6 (20230816)
(V1.0 first published 20230214)
Firmware
Firmware version can be verified on
Verkada Command command.verkada.com.
2
Product Models
This install guide pertains to TD52-HW.
UL294 Performance Levels
●Attack Level: Level I
●Endurance Level: Level I
●Line Security Level: Level I
●Standby Power Level: Level I
CAN/ULC-60839-11-1
●Environmental Level: Outdoor
●Grade assignment: Grade I
Note: Video, audio, and intercom performance were not
evaluated by UL. Additionally, PoE+ functionality (extended
temperature range) was not evaluated by UL.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
3
Introduction
Technical Specifications
Sensor Resolution 5MP (2688 x 1944)
Lens Type Fixed
Image Sensor 1/2.8” Progressive CMOS
Focal Length 2.12mm
Iris Fixed
Aperture F2.0
Field of View Horizontal: 130°
Vertical: 100°
Diagonal: 160°
IR Range 15m / 50ft in low light
Onboard Storage 256GB
Audio Streaming Two-way, full duplex with echo cancellation and noise suppression
Audio Output 5W speaker ; 90dB SPL at 1m / 3.3ft
Audio Input 2 omnidirectional digital MEMs microphones
Inputs / Outputs 2x dry inputs
1x dry relay, 30VDC @ 1A (resistive load)
1x RS-485 port, 12V @ 250mA output
Dimensions 238mm (L) x 128mm (W) x 44mm (H)
9.4in (L) x 5in(W) x 1.7in (H)
Weight 1.1kg/2.3lb
Tamper Detection Yes
Resistance Rating IK08, IP66
Operating Specs Power: 11.5W (IEEE 802.3af PoE) ; Extended Temperature Range: 25.5W (IEEE 802.3at PoE)
Temperature: -20°C – 50°C / -4°F – 122°F, PoE 802.3af ; -40°C – 50°C / -40°F – 122°F, PoE 802.3at
Humidity: 90%
Compliance FCC Part 15B Class B, ICES-003 Class B, CE, UKCA, KCC, RCM, VCCI, UL/IEC 62368-1, CSA NO22.2
62368-1, UL 294, ULC-60839-11-1 Outdoor
Connectivity Ethernet: 10/100Mbps RJ-45 cable connector for Network/PoE connection
Included Accessories T10 screwdriver, mounting hardware kit, grommet punch
Mounting Options Flush mount plate (included), surface mount box (separate accessory), angle mount box
(separate accessory), trim plate (separate accessory), rain hood (separate accessory)
Introduction
What’s in the box
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
4
What you’ll need
●A working internet connection
●A smartphone or laptop
●A #2 Phillips head and power drill
●A level
Connect
Connect the TD52 to your network using the
Ethernet port located behind the rear door of the
device.
Supports PoE and PoE+. PoE+ required for full functionality,
including extended temperature range (down to
-40C/-40F) and RS-485 support. Shall be powered by an
UL294 and ULC-68039-11 certified PoE Power Supply. Note,
PoE+ ratings were not evaluated by UL.
After connecting the TD52 to network and power,
visit: verkada.com/start
For detailed installation instructions, visit:
verkada.com/support
TD52 Flush Mount Plate
T10 Security Torx Screwdriver (1 pcs)
Drywall Screws (4 pcs) Drywall Anchors (4 pcs)
M4x18mm Machine Screws (4 pcs)
(silver)
8-32 ¾” Machine Screws (4 pcs)
(black)
Grommets (2 pcs) Grommet Punch (1 pcs)
Off
Intercom is unpowered
On
Intercom is powered
Introduction
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
5
Ambient Light
Sensor
Status LED
Status LED Behavior
Solid Orange
Intercom is on and booting up.
Flashing Orange
Intercom is updating firmware.
Flashing Blue
Intercom is managing doors,
but cannot reach the server.
Solid Blue
Intercom is managing doors
and connected to the server.
Flashing Pink
Identify.
Call Button
with LED
Camera
Speaker
Overview
Microphones
I/O Terminal
Block
PoE Port
Feedback
LEDs
Call Button LED Behavior
Introduction
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
6
Feedback LEDs
Normal Behavior
Cascading White
The call button has been pressed
and the intercom is making a call.
Solid White
The call has been connected and
audio/video is being shared.
Solid Green
The door has been unlocked.
Setup Behavior
Intercom is connected to power and booted
Intercom has an IP address
Intercom has connected to Verkada’s server
Intercom has commissioned and has an authentication token
Intercom can connect to Twillio’s server and register with SIP
Intercom has all required ports enabled
Intercom has a valid receiver and is ready to make a call
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
7
To add the TD52 to your Verkada
Command account, go to:
command.verkada.com/add-device
Enter the serial number printed on the
back of the device, the packaging, or
the order number.
If you would like to update and
configure TD52 before mounting it,
connect the device to your network
using the Ethernet port located in the
cable bay on the back of the device.
Installation
Connect
Serial Number
Installation
Mounting 1/7
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
8
The flush mount plate has holes
configured for the following mounting
conditions:
A/B Legacy intercom back box
Direct wall mounting
C 4-gang junction box mounting
Use the corresponding holes to mount
to an existing intercom back box (A/B)
or 4-gang junction box (C).
Direct wall mounting
To mount directly to a wall, use the
mount plate as a template to mark
mounting holes (B) and the center
cutout.
Use the marks to drill pilot holes for the
mount plate. For direct mounting, drill
3mm pilot holes. When using wall
anchors, drill 6mm pilot holes.
Use the supplied screws to install the
mount plate onto the wall. Ensure that
the labels (A, B, C) on the mount plate
are facing away from the wall.
Please note: The supplied screws are intended
to cover most possible install cases. Be sure to
use the best screws for your specific job.
Installation
Mounting 2/7
Route the building-side cable
through the hole in the center of
the mount plate.
On the rear of the device, loosen
the four T10 Torx Security screws on
the cable bay door to access the
ethernet and I/O ports.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
9
Installation
Mounting 3/7
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © 2022 Verkada Inc. All rights reserved.
10
Attach grommet punch to the RJ-45 cable.
Insert the RJ-45 ethernet cable through the
right grommet using the included grommet
punch and pass through the cable bay door.
Remove the grommet punch and Insert the
RJ-45 ethernet cable into the PoE port.
Altri manuali per TD52
1
Indice
Altri manuali Verkada Sistema di interfono
