Versaclean 200H-230V Manuale utente
07-02083A 200-230V, 200H-230V, 500-230V, 500H-230V, 1200-230V 1 VersaClean
User Manual
Portable Extractors
Models 200-230V, 200H-230V, 500-230V, 500H-230V, 1200-230V
VersaClean Portable Extractors provide deep, rapid cleaning of carpets, upholstery and hard
surfaces. Heated models provide additional cleaning power. Lightweight, easy to use, and
adjustable for a wide range of carpet types and soiling conditions, the VersaClean Extractors
produce cleaner, drier carpets and surfaces.
Patents: http://www.LBpatents.com
READ AND SAVE THESE INSTRUCTIONS
WARNING! Do not alter or modify your unit in any
way. Use only replacement parts authorized by
VersaClean. Modifications or use of unapproved
parts could create a hazard and will void your
warranty. Contact your authorized VersaClean
distributor for assistance.
WARNING! Electric shock hazard, rotating fan
hazard and hot surface hazards.
•Inspect the power cord before use. If cord is
damaged, do not use. Always grasp the plug
(not the cord) to unplug.
•Insert three-prong plug on power cord into a
matching electrically grounded outlet. Do not
use adapter. Never cut off third prong. Do not
use an extension cord.
•The unit must be operated on two separate
230V/50 Hz circuit protected by a Residual
Current Device (RCD).
•Keep motor and wiring dry.
•Always unplug unit before cleaning or
servicing.
•Do not attempt to repair the unit. For service,
contact your local VersaClean distributor.
BEFORE YOU BEGIN
Warranty registration
Warranty registration procedures vary by
country/market. Contact VersaClean for assistance.
Registration allows us to better assist you with using,
maintaining or servicing your equipment and to contact
you in case we have important safety information
concerning your VersaClean product. If you determine
service is required, have your equipment model, serial
number and original proof of purchase available and ask
for assistance with obtaining a return material
authorization (RMA).
A
D
B
C
FIG. 1: Front View
A
Recovery tank cover
B
Vacuum hose attachment
C
Recovery tank gravity drain and gate-type valve
D
Solution hose quick-connect
07-02083A 200-230V, 200H-230V, 500-230V, 500H-230V, 1200-230V 2 VersaClean
GROUNDING INSTRUCTIONS
This unit’s plug must be inserted into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
WARNING! Improper connection of the equipment-
grounding conductor can result in a risk of electric
shock. Check with a qualified electrician or service
person if you are in doubt as to whether the outlets
are properly grounded. Do not modify the plug
provided with the appliance – if the plug does not fit
the outlets, have proper outlets installed by a
qualified electrician.
This equipment is for use on circuits with a nominal
rating of no more than 230V.
Handle the unit carefully
Always operate the unit on a stable, level surface. Do
not drop, throw, or place where it could fall. Rough
treatment can damage the unit, and may create a
hazardous condition or void the warranty.
This unit intended for household and commercial use.
CONTROLS
ON THE CONTROL PANEL (see Fig. 3)
Includes rocker-type switches control blower, solution
pump, and heat (on select models). Heated units are
equipped with a second power cord. The second power
cord must be plugged in to a separate electric power
source.
Pressure regulator (Fig. 2, F).Select models. Turn
clockwise to increase solution pressure; turn
counterclockwise to decrease solution pressure.
Pumpout switch (Fig. 2, E) Select models. Switch to on
position to activate pumpout.
OPERATING INSTRUCTIONS
1. Pre-mix cleaning solution with hot water in a
separate container. Pour mixed solution into the
solution tank of the machine.
A
D
B
G
C
F
H
E
FIG. 2: Rear View
(Detail)
A
I
J
A
Solution tank with clear hinged cover
F
Exhaust outlet – keep clear
B
Wand retention clip
G
Pressure gauge (select models)
C
Vacuum exhaust. Keep clear.
H
Pressure regulator (select models)
D
Product label and serial number
I
Pumpout coupling (select models). Keep capped when not in use.
E
Dual cords (select models)
J
Auto-Fill coupling (select models)
07-02083A 200-230V, 200H-230V, 500-230V, 500H-230V, 1200-230V 3 VersaClean
IMPORTANT: Take care to control foaming in the
vacuum system. Excessive foam can allow moisture,
carpet fiber and other debris to be drawn through the
vacuum cutoff valve and cause damage to the vacuum
motors. Damage caused by moisture or debris will void
the product warranty. To help reduce foaming, use a
low-foam detergent. Foaming may also occur because of
residues left from previous cleanings. If this happens,
use a defoamer additive. Follow defoamer manufacturer
instructions for proper application.
2. Connect vacuum and solution hoses to machine and
attach to extraction wand or hand tool.
3. Plug power cord into a 3-pin grounded circuit. Keep
cords clear of your cleaning path. IMPORTANT:
Heated units have two cords and should be plugged
into separate 3-pin grounded circuits.
4. Switch on vacuum.
5. Switch on solution pump.
6. For heated solution (Heated units only).
7. Begin cleaning. Refer to industry-approved
procedures.
8. If equipped, solution pressure may be adjusted with
the pressure regulator knob (Fig. 2, G). Monitor the
pressure gauge to ensure pressure is adequate.
CAUTION: When the recovery tank reaches capacity,
an automatic float valve blocks vacuum intake (see
Fig. 7) and the vacuum motors will make a high
pitched noise. When this occurs, switch the machine
off immediately to prevent damage to the vacuum
motors.
9. When cleaning is completed, rinse solution tank with
clear water to ensure no detergents or rinse agents
remain in the tank.
10. Empty and rinse the waste tank thoroughly. This will
help to prevent the formation of damaging deposits
and reduce the growth of odor-causing bacteria.
11. Turn on vacuum motor and allow it to run for 15
minutes to help remove any moisture from the
vacuum motors and assure long vacuum life.
For maintenance instructions, see “Maintenance,” p. 3.
MAINTENANCE (ALL UNITS)
WARNING: Unplug machine before servicing.
Possibility of electrical shock.
WARNING: Interior components may be hot after
operation. Let unit cool completely before servicing.
FIG. 4: Solution inlet filter cleaning
Remove
9/16 in.
nut with
wrench
and lift
open top.
Unscrew
filter
cap and
rinse
clean.
A
D
B
G
C
F
FIG. 3: Control Panel
E
Power ON/OFF
Solution pressure pump ON/OFF
Solution heater ON/OFF (select models)
Pumpout ON/OFF (select models)
07-02083A 200-230V, 200H-230V, 500-230V, 500H-230V, 1200-230V 4 VersaClean
DAILY OR AFTER EACH USE
Clean the solution inlet filter (Fig. 4) Loosen tank
attachment screw (Fig. 1) and open unit. Remove filter
cover and strainer screen (Fig. 5). Rinse strainer screen
clean in warm water. Replace strainer and retighten filter
cover.
Clean vacuum cutoff valve and strainer (Fig. 5).
Empty recovery tank, then open recovery tank lid. Grasp
valve assembly and gently pull downward, taking care
not to distort the strainer screen. Rinse assembly clean
and make sure float ball moves freely inside assembly.
Reinstall securely.
AS NEEDED
Lubricate pressure regulator O-ring (if equipped).
Access O-ring by unscrewing and removing pressure
regulator (Fig. 2, F). Lubricate with a suitable O-ring
lubricant.
Lubricate the solution line quick-connect coupling
(Fig. 1, D) with a small amount of rust-inhibiting oil such
as LPS-3 or WD-40.
To maintain appearance, wipe interior and exterior
surfaces with a damp cloth. For deep cleaning and a
lasting, protective shine, use an automotive vinyl
cleaner/protectant product.
FIG. 5: Vacuum cutoff valve cleaning
FIG. 6: Solution tank strainer
(pumpout models only)
Slide filter upward to remove. Rinse
filter clean with water and reinstall.
07-02083A 200-230V, 200H-230V, 500-230V, 500H-230V, 1200-230V 5 VersaClean
CHANGING THE 1200-230V PRESSURE PUMP OIL
Tools required:
Manual transfer pump
Clean cloths
Suitable oil waste/recycling container
Verify both tanks are empty. Use a cloth to wipe out any residual moisture. Place clean cardboard or a pad behind unit
to protect handle. Remove retaining nut, hinge open unit and rest on pad.
Remove oil fill cap on pressure pump
Insert suction tube of transfer pump into oil fill hole. Pump out oil to a suitable waste / recycling receptacle.
Insert suction tube of transfer pump into bottle of fresh oil and pump approximatel 8 oz. of oil into pressure pump.
After placing approximately 8 oz. of oil into the pump, check
the oil level with the dipstick. Level should be within the
notched area on the dipstick. If necessary, add oil and
recheck with the dipstick until oil is at the correct level.
When filling is complete, reinstall install oil cap, close unit and reinstall retaining nu
t.
Dispose of used oil appropriately.
The 1200-230V is now ready for use.
WARRANTY
Warranty information is available from your dealer or at
www.VersaCleanSystems.com.
OPTIONS (PURCHASED SEPARATELY)
Wand and Vacuum Hose Kit (48-075): Wand, 25 ft. ¼ in.
solution hose and 25 ft. 1½ in. vacuum hose
Upholstery Pro (67-019)
07-02083A 200-230V, 200H-230V, 500-230V, 500H-230V, 1200-230V 6 VersaClean
SPECIFICATIONS
ALL MODELS
Vacuum motor
6.6 Ametek Vac Motor
Capacity
Solution / recovery tank 12 gal. | 45.4 l
Recovery tank: 10 gal. | 37.9 l
Construction
Rotomolded polyethylene housing and handle;
semi-pneumatic wheels.
Drain valve
Gate type
Float shut-off
Ball type
Accessories
included
25 ft. of ¼ in. solution hose
25 ft. of 2 in. vacuum hose
Dimensions
(H × L × W)
39.5 × 32 × 19.75 in.
100.3 × 81.2 × 50.2 cm
Model
Features
Current draw
200-230V
200 PSI
Circuit 1: 7.0 amps
200H-230V
200 PSI Heated
Circuit 1: 7.0 amps
Circuit 2: 7.6 amps
500-230V
500 PSI. Adjustable high
pressure pump with gauge.
Circuit 1: 8.5 amps
500H-230V
500 PSI Heated. Adjustable
high pressure pump with
gauge.
Circuit 1: 8.5 amps
Circuit 2: 7.6 amps
1200-230V
Adjustable high pressure
pump with gauge. Auto-fill.
Pumpout
Circuit 1: 6.7 amps
Circuit 2: 7.5 amps
CONTACT
VersaClean
15180 Josh Wilson Road
Burlington, WA 98233
800-932-3030 www.VersaCleanSystems.com
FIG. 7: Gravity drain diverter
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali Versaclean Scrubber
