Vertex Standard VX-127 Manuale utente

FCC ID: K6620224X20

IC IF: 511B-20224X20

Alignment

Vertex Standard Co., Ltd.

VX-127/VX-177 Alignment

Introduction and Precautions

The VX-127/VX-177 has been carefully aligned at the factory for the specified performance

across the 430 MHz amateur band. Realignment should therefore not be necessary except

in the event of a component failure. All component replacement and service should be

performed only by an authorized Yaesu representative, or the warranty policy may be

voided.

The following procedures cover the sometimes critical and tedious adjustments that are not

normally required once the transceiver has left the factory. However, if damage occurs and

some parts are replaced, realignment may be required. If a sudden problem occurs during

normal operation, it is likely due to component failure; realignment should not be done until

after the faulty component has been replaced.

We recommend that servicing be performed only by authorized Yaesu service technicians

who are experienced with the circuitry and fully equipped for repair and alignment. Therefore,

if a fault is suspected, contact the dealer from whom the transceiver was purchased for

instructions regarding repair. Authorized Yaesu service technicians realign all circuits and

make complete performance checks to ensure compliance with factory specifications after

replacing any faulty components.

Those who do undertake any of the following alignments are cautioned to proceed at their

own risk. Problems caused by unauthorized attempts at realignment are not covered by the

warranty policy. Also, Yaesu must reserve the right to change circuits and alignment

procedures in the interest of improved performance, without notifying owners.

Under no circumstances should any alignment be attempted unless the normal function and

operation of the transceiver are clearly understood, the cause of the malfunction has been

clearly pinpointed and any faulty components replaced, and the need for realignment

determined to be absolutely necessary.

FCC ID: K6620224X20

IC IF: 511B-20224X20

Alignment

Vertex Standard Co., Ltd.

Required Test Equipment

The following test equipment (and thorough familiarity with its correct use) is necessary for

complete realignment. Correction of problems caused by misalignment resulting from use of

improper test equipment is not covered under the warranty policy. While most steps do not

require all of the equipment listed, the interactions of some adjustments may require that

more complex adjustments be performed afterwards. Do not attempt to perform only a

single step unless it is clearly isolated electrically from all other steps. Have all test

equipment ready before beginning, and follow all of the steps in a section in the order

presented.

Regulated DC Power Supply: adjustable from 5 to 16 VDC, 3 A

RF Signal Generator with calibrated output level at 500 MHz

Frequency Counter: ±0.1 ppm accuracy at 500 MHz

AF Signal Generator

SINAD Meter

Oscilloscope

Spectrum Analyzer

Deviation Meter (linear detector)

AF Milivoltmetr

AF Dummy Load: 8 Ω, 1 W

DC Voltmeter: high impedance

Inline Wattmeter with 5% accuracy at 500 MHz

50-Ohm non-reactive Dummy Load: 10 watts at 500 MHz

VHF/UHF Sampling Coupler

Alignment Preparation & Precautions

A dummy load and inline wattmeter must be connected to the main antenna jack in all

procedures that call for transmission, except where specified otherwise. Correct alignment is

not possible with an antenna. After completing one step, read the following step to

determine whether the same test equipment will be required. If not, remove the test

equipment (except dummy load and wattmeter, if connected) before proceeding.

Correct alignment requires that the ambient temperature in the repair shop be the same as

that of the transceiver and test equipment, and that this temperature be held constant

between 20 °C and 30 °C (68 °C to 86 °F). When the transceiver is brought into the shop

from hot or cold air it should be allowed some time for thermal equalization with the

environment before alignment. If possible, alignments should be made with oscillator shields

FCC ID: K6620224X20

IC IF: 511B-20224X20

Alignment

Vertex Standard Co., Ltd.

and circuit boards firmly affixed in place. Also, the test equipment must be thoroughly

warmed up before beginning.

Notes: Signal levels in dB referred to in alignment are based on 0 dBµ = 0.5 µV.

All items tune and/or adjust by Auto-Tuning Mode or Manual Tuning Mode.

PLL Reference Frequency

With the wattmeter, dummy load and frequency counter connected to the antenna jack.

Tune the transceiver 435.05 MHz and set the TX power level to low power mode.

Key the transceiver, adjust the counter frequency is within ±100 Hz of 435.05 MHz.

Transmitter Deviation

With the wattmeter, dummy load and deviation meter connected to the antenna jack.

Inject a 1 kHz audio signal as a level of 80 mV to the microphone-input port.

Key the transmitter on 440.05 MHz. Adjust the frequency deviation is within 4.3-4.7 kHz

on the deviation meter.

CTCSS Deviation

With the wattmeter, dummy load and deviation meter connected to the antenna jack.

Key the transmitter on 440.05 MHz. Adjust the frequency deviation is within 0.65-0.75

kHz on the deviation meter.

DCS Deviation

With the wattmeter, dummy load and deviation meter connected to the antenna jack.

Key the transmitter on 440.05 MHz. Adjust the frequency deviation is within 0.65-0.75

kHz on the deviation meter.

FCC ID: K6620224X20

IC IF: 511B-20224X20

Alignment

Vertex Standard Co., Ltd.

Transmitter Power

With the power meter, dummy load and deviation meter connected to the antenna jack.

Key the transmitter on 440.05 MHz. Adjust the output power is within 5 ±0.1 W on the

power meter. (HI)

Key the transmitter on 440.05 MHz. Adjust the output power is within 2 ±0.1 W on the

power meter. (MID)

Key the transmitter on 440.05 MHz. Adjust the output power is within 0.5 ±0.05 W on

the power meter. (LOW)

Receiver Sensitivity

With the dummy load and SINAD meter connected to the external speaker jack.

Inject a RF signal as a level of -9 dBµV to the antenna jack.

Tune the receiver on 440.05 MHz. Adjust the SINAD is above 12 dB on the SINAD

meter.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Vertex Standard Ricetrasmettitore

Vertex Standard

Vertex Standard VX-160U Manuale utente

Vertex Standard

Vertex Standard VX-230 Series Manuale utente

Vertex Standard

Vertex Standard VX-1700 Series Manuale utente

Vertex Standard

Vertex Standard HX750S Manuale utente

Vertex Standard

Vertex Standard VX-450 series Manuale utente

Vertex Standard

Vertex Standard Spirit VXA-700 Manuale utente

Vertex Standard

Vertex Standard VX-210AV Manuale utente

Vertex Standard

Vertex Standard FTM-10SR Manuale utente

Vertex Standard

Vertex Standard VXA-710 SPIRIT Manuale utente

Vertex Standard

Vertex Standard VXA-150 Manuale utente

Vertex Standard

Vertex Standard VX-7200 Manuale utente

Vertex Standard

Vertex Standard VX-2500U Manuale utente

Vertex Standard

Vertex Standard VX-2500EV Manuale utente

Vertex Standard

Vertex Standard VX-925E Manuale utente

Vertex Standard

Vertex Standard VX-1700 Series Manuale utente

Vertex Standard

Vertex Standard Yaesu FT-270R/E Manuale

Vertex Standard

Vertex Standard GX1255S Manuale utente

Vertex Standard

Vertex Standard VX-3R Manuale

Vertex Standard

Vertex Standard VX-261 Manuale utente

Vertex Standard

Vertex Standard VX-120 Manuale utente

Vertex Standard

Vertex Standard VX-350 series Manuale utente

Vertex Standard

Vertex Standard HX300 Manuale utente

Vertex Standard

Vertex Standard VX-420E series Manuale utente

Vertex Standard

Vertex Standard VX-450 series Manuale utente

Manuali Ricetrasmettitore popolari di altre marche

Yaesu

Yaesu FT-7B Manuale utente

Kenwood

Kenwood ProTalk TK-3201 Manuale utente

Texas Instruments

Texas Instruments TLK10232 Manuale utente

Mizuho

Mizuho MX-2 Guida del prodotto

Kenwood

Kenwood TK-3180 Manuale operativo e di manutenzione

Blitz

Blitz MJ-398U Manuale utente

Utilicom

Utilicom LongRanger 2050 Manuale utente

Standart

Standart HX290UKA Manuale utente

Altronix

Altronix Pace1PTM Manuale utente

Kirisun

Kirisun PT2208 Manuale utente

ELECRAFT

ELECRAFT KX2 Manuale utente

Zodiac

Zodiac K3 Manuale utente

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuale utente

Kenwood

Kenwood TK-2217 Manuale utente

Siemens

Siemens PSO 4000 Manuale utente

Kenwood

Kenwood TS-590SG Manuale utente

Midland

Midland G8E-BT Manuale

ComNav

ComNav Mariner X2 Manuale utente