VETRON 5300 Manuale utente
5300 » INSTRUCTION MANUAL
07/2020
STANDARD
»5300
»5320
DEEPSTITCH
»5380
5300 » INSTRUCTION BOOK
07/2020
© VETRON | TYPICAL GmbH
Clara-Immerwahr-Str. 6
67661 Kaiserslautern, Germany
Tel.: +49 6301 320 75 - 0
Fax: +49 6301 320 75 - 11
info@vetrontypical.com
www.vetrontypical.com
All rights reserved.
The instructions for use, service instructions, parts lists are protected by copyright. Any reuse of the
content outside the copyright is without the written consent of VETRON | Typical GmbH inadmissible
and punishable.
VETRON | Typical GmbH is only liable for damage caused by intent or gross negligence on the part of
the manufacturer. Otherwise, liability is excluded.
Reserve technical changes!
The contents were carefully prepared and checked by the publisher. Due to continuous development,
illustrations, functional steps and technical data may dier slightly.
Updating the documentation
If you have suggestions for improvement or have detected any irregularities, please contact us.
The documents for the machines can be accessed by logging on
https://www.vetrontypical.com/ downloaded for free.
CE marked after §7 Prod SG
03
07/2020
VETRON 5300 - POST BED MACHINE - INSTRUCTION BOOK
INDEX
VETRON 5300 - POST BED MACHINE
01. PREFACE
05 01. SAFETY INSTRUCTIONS
06 02. SYMBOLISM
07 03. DANGER NOTES
08 04. PRODUCT INTRODUCTION / INTENDED USE / CONFORMITY DECLARATION
09 05. TECHNICAL DATA
10 06. TRANSPORT - PACKAGING - DISPOSAL - STORAGE |
FIRST COMMISSIONING / DECOMMISSIONING
11 07. MOUNTING SAFETY DEVICES FOR TILTING (CYLINDER)
12 07.01. SAFETY DEVICES FOR TILTING (CHAIN)
13 07.02. SAFETY DEVICES FOR TILTING (SAFETY SPRING)
02. MACHINE DESCRIPTION
15 01. OVERVIEW
16 02. OPERATING PANEL
17 03. HOTKEYS
18 04. ELECTRONIC HANDWHEEL & REVERSE SEWING
19 05. CONTROL & MAIN SWITCH
20 06. PEDAL
21 07. LIGHT
22 08. MACHINE START
23 09. PROGRAM CHANGE
24 10. DIRECT ACCESS
04 07/2020
VETRON 5300 - POST BED MACHINE - INSTRUCTION BOOK
03. OPERATION OF THE MACHINE
25 01. INSERTING THE NEEDLE (1- NEEDLE)
26 01.01. INSERTING THE NEEDLE (2- NEEDLE)
27 02. SEWING FEET EXCHANGE
28 03. THREADING THE MACHINE (1- / 2- NEEDLE)
29 04. EXCHANGING THE BOBBIN AND ADJUSTING THE BOBBIN THREAD TENSION
30 05. WINDING THE BOBBIN THREAD
31 06. ENGAGING THE SAFETY CLUTCH
32 07. SAFETY SPRING
04. MAINTENANCE
33 01. MAINTENANCE INTERVALS
34 02. OIL LEVEL CHECK
35 03. CLEANING THE MACHINE
36 04. SEWING DRIVE
37 05. PNEUMATIC SYSTEM
05. PROGRAMMING
39 01. GENERAL
40 02. CREATE PROGRAMNAME AND STORING
41 03. CHANGE PROGRAM NAME
42 04. PROGRAM PARAMETER
06. WEAR PARTS
69 01. GENERAL INFORMATION
70 02.01. LISTING
07. WIRING DIAGRAM
73 01. VETRON 8340 CONTROL BOX
INDEX
VETRON 5300 - POST BED MACHINE
05
07/2020
VETRON 5300 - POST BED MACHINE - INSTRUCTION BOOK
01. PREFACE
01. SAFETY INSTRUCTIONS
General Safety Instructions
This manual and the warning symbols on the machine should en-
sure the safe use of the machine, so that no accidents and injuries
may occur to you and others. Please read this instruction and also
the safety instructions of the motor manufacturer carefully.
» The machine must only be operated in accordance with its
intended purpose (for example, sewing medium to heavy ma-
terials such as jeans, leather, etc. NO tin!) and with the as-
sociated protective equipment. The relevant country-specific
safety regulations and technical data must also be observed.
» The machine should only be used in accordance with its inten-
ded purpose (eg sewing medium to heavy materials such as
jeans, leather, etc.) and with the associated protective equip-
ment. The relevant country-specific safety regulations and
the technical data must also be observed.
» The machine should only be set up and operated in dry and
well-kept rooms.
» Do not place the machines outdoors, next to radiators or heat
source. The ambient temperature should not be lower or hig-
her than between 0° C to 45° C.
» The machine must only be commissioned after the relevant
operating instructions have been taken into consideration and
by appropriately instructed operators.
»These instructions are to be stored at hand.
» The connection cable must be provided with a country-
specific approved mains plug. The mains plug must only be
connected to grounded sockets. Here a qualified specialist is
necessary.
» The machine must always have a grounding. Only over this is
a normal operation of the machine to ensure.
» The danger and safety instructions attached to the machine
must be followed.
» When replacing sewing tools such as needle, sewing
foot, stitch plate, feed dog or bobbin, when threading,
when leaving the workplace and during maintenance,
etc., the machine must be disconnected from the mains.
Press the main switch or pull out the mains plug.
» Machines with compressed air components must be discon-
nected from the compressed air supply and the residual pres-
sure released before repair or maintenance work. Exceptions
to this are performance tests or specific settings.
» Repairs and all maintenance work should only be carried out
by qualified personnel or appropriately instructed persons.
» Work on electrical equipment must only be carried out by
qualified specialists.
If errors are detected, stop the machine immediately.
» Work on parts and equipment that are live is not permitted.
The machine must be disconnected from the mains.
» Modifications or modifications to the machine must be carried
out in compliance with all relevant safety regulations. The
manufacturer assumes no responsibility for damage caused
by changes or modifications.
» For repairs, only spare parts approved by VETRON may be
used. In case of infringement the guarantee expires.
»The machines are to be used only for the purpose intended.
» If oils, greases, etc., used for the machines and accessories,
get in your eyes or on your skin, or should you swallow any of
these fluids, wash them immediately and thoroughly, or seek
medical attention immediately.
» Commissioning of the machine is prohibited until it has been
determined that the entire sewing unit complies with the pro-
visions of the EC directive and the declaration of conformity
has been created.
Advice to the Owner
»
As part of the machine, this operating manual must be availab-
le to operating personnel at all times. Before using the machine
for the first time, the operator must read this operating manual.
» The operator has to ensure that the machine is only operated
in perfect condition.
» The operator must ensure that no safety devices are removed
or disabled.
» The operator must ensure that only authorized or properly in-
structed persons work on the machine.
»
The operator must therefore ensure that the workstations ac-
cording to ASR lux. 4 are adequately illuminated (min. 750 lux).
Operators and Technical Sta
» The operating personnel are responsible for setting up, ope-
rating and cleaning the machine and responsible for the eli-
mination of faults.
» Qualified personnel include people with specialist trai-
ning in electrical / electronics, pneumatics and mechanics.
Lubrication, maintenance, repair and adjustment are your
responsibilities.
» The operator must refrain from any operation that impaires
the safety on the machine.
1. Jewelry, chains and rings - must not be worn.
2. The clothes should be tight
3.
Only authorized persons may enter the danger area.
» If changes occur to the machine that aect safety, they must
be reported immediately to the operator.
» The specialist personnel - persons with training in electrical /
electronics and mechanics - are responsible for the lubrica-
tion, maintenance, repair and adjustment of the machine.
» Before starting adjustment and repair work, the main switch
must be switched o and secured against reclosing.
» Work on parts that are under tension should be avoided. Ex-
ceptions are regulated by EN 50110. After maintenance and
repair work, the protective covers must be replaced.
»
Operating and specialist personnel are obliged to observe the sa-
fety instructions given in the instructions for use during all work.
06 07/2020
VETRON 5300 - POST BED MACHINE - INSTRUCTION BOOK
01. PREFACE
02. SYMBOLISM
DANGER!
This symbol in combination with the
word DANGER, indicates an imminent
danger that may result in serious injury
or death.
WARNING!
This symbol in combination with the
word WARNING indicates a potentially
hazardous situation which, if not avoided,
could result in serious injury or death
ATTENTION!
This symbol in combination with the
word ATTENTION may indicate a
potentially hazardous situation that
could result in minor personal injury
.
DANGER OF CUTS!
This symbol indicates that there is an
increased risk of cuts here.
CRUSHING!
This symbol indicates that there is a
heightened risk of crushing
RISK OF BURNS!
This symbol indicates that there is an
increased risk of burning here.
MAGNET!
This symbol indicates that there is a
magnet field.
INFORMATION!
This symbol displays information.
ADVICE!
This symbol indicates important
information
.
HARMFUL TO HEALTH!
May damage certain organs. Can lead to
immediate and long-term massive
impairment of health, cause cancer,
damage genetic material, fertility or
development. May be fatal if infiltrated
into the respiratory tract.
HAZARD TO WATERS!
May cause acute or long-term damage
to aquatic organisms such as fish,
aquatic insects and aquatic plants in low
concentrations.
PROTECTIVE EARTHING!
Earthing one or more points of a
network, installation or equipment for
the purpose of electrical safety.
1
2
OFFON
DANGER LABEL
Do not work the machine without finger
guard and safety covers!
Before threading, changing the needle,
adjusting, changing the bobbin, cleaning,
maintenance, etc. switch o the main
switch on the control.
07
07/2020
VETRON 5300 - POST BED MACHINE - INSTRUCTION BOOK
01. PREFACE
03. DANGER NOTES
1 THREAD TAKE UP LEVER
2 SEWING ZONE
3 BOBBIN THREAD WINDER
4 ZONE BETWEEN MACHINE AND TABLE
CRUSHING
Crushing and bruising through the thread take up lever 1
Make sure thread take up lever guard is mounted.
Risk of injury due to movement of the lever.
CRUSHING
Crushing and bruising through the needle and sewing feet 2
Make sure finger guard is mounted.
Risk of injury through needle and feet movement.
DANGER OF CUTS
Cuts through rotation 3
Keep distance from bobbin winder while winding.
Risk of injury due to rotation.
CRUSHING
Crushing and bruising due to tilting the machine 4
Make sure safety spring 5 is mounted.
Risk of injury when machine is tilted back.
SAFETY PRECAUTIONS
The eye protection 6 can be ordered optionally, but must not be removed
after installation without consultation with the operator.
The finger guard 7 must not be removed!
6 EYE GUARD
5 SAFETY SPRING
7 FINGER GUARD
08 07/2020
VETRON 5300 - POST BED MACHINE - INSTRUCTION BOOK
1-/ 2-NEEDLE LOCKSTITCH SEWING MACHINE WITH DIRECT DRIVE
AND TRIPLE FEED
The consistent use of state-of-the-art control technology has made it possible to program all ma-
chine parameters programmatically, making them directly accessible. This ensures that the process
parameters are free from operator influence and after each setup.
The innovative dynamic machine parameters based on the current speed and the permanent materi-
al thickness measurement open up new paths in terms of processing quality, process reliability and
reducing cycle times.
Typical applications:
Automotive Upholstery Suitcase Bag
INTENDED USE
Any use not approved by the manufacturer is considered improper!
Proper use also includes compliance with the prescribed operating, adjustment,
maintenance and repair measures. Damage due to non-intended use is not covered by
the manufacturer‘s liability!
The VETRON 5300 and its subclasses are 1- and 2- needle lockstitch sewing machine with direct
drive and triple feed. Use the machines only according to their technical data and for medium to
heavy materials such as jeans, leather, etc.. No tin! The machine is only intended for processing
dry material and must not contain any hard objects. In this respect, the seam must be made with a
thread whose requirement profile corresponds to the application purpose.
The machine is designed for industrial use.
The operator is obliged to carry out a risk assessment in accordance with the Work Protection Act
(ArbSchG).
CE-CONFORMITY DECLARATION
All VETRON sewing machines comply with the applicable European regulations of relevant basic
health and safety requirements, which are specified in the declaration of conformity and manufac-
turer.
01. PREFACE
04. PRODUCT INTRODUCTION / INTENDED USE / CONFORMITY DECLARATION
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali VETRON Macchina da cucire
VETRON
VETRON 5064 Manuale utente
VETRON
VETRON 4000 Manuale utente
VETRON
VETRON 5000 Manuale utente
VETRON
VETRON 5400 Manuale utente
VETRON
VETRON 5390 Manuale utente
VETRON
VETRON 5374 Manuale utente
VETRON
VETRON 5000 Manuale utente
VETRON
VETRON Typical GC6890 Manuale utente
VETRON
VETRON 5000 Manuale utente
VETRON
VETRON 5000 Manuale utente
