Vicon VC-700 Manuale utente

VC-700 and VC-710

COLOR DOME CAMERAS

About this manual

Surface-Mount configuration In-Ceiling configuration

INSTRUCTION MANUAL XX178-00

Dimensions : inch (mm)

Before installing and using the camera, please read this manual carefully.

Be sure to keep it handy for later reference.

This installation should be made by a qualified service person and should conform to the

National Electric Code, ANSI/NFPA 70 and all local codes.

Installers should use appropriate hardware mounting materials.

PRECAUTIONS

■Do not open or modify

Do not open the case except during maintenance and installation, as it may be

dangerous and cause damages.

■Do not put objects inside the unit

Make sure that no metal objects or flammable substances

get inside the camera. It could cause fire, short-circuits or damages.

■Be careful when handling the unit

To prevent damage, do not drop the camera or subject it to strong shock or

vibration.

■Install away from electric or magnetic fields

■Protect from humidity and dust

■Protect from high temperature

Be careful when installing close to the ceiling , in a kitchen or boiler room,

as the temperature may rise to high levels.

■Cleaning

Dirt can be removed from the case only by wiping it with a soft cloth moistened

with a soft detergent solution.

■Mounting Surface

The mounting surface material must be strong enough to support the camera.

TROUBLESHOOTING

LENS ADJUSTMENT

Before sending the camera out for repair, check the items below.

If the problem persists after checking these items, contact your service center.

■If no image appears

Is the coaxial cable attached securely?

Are the power and voltage normal?

Has the iris of the lens inside the camera been

adjusted correctly (with the level volume) ?

Is there adequate illumination?

■If the image is unclear

Is the lens in focus?

Is the lens dirty?

Dirt or fingerprints on the lens can adversely affect the

images. Gently wipe any dirt or fingerprints off the lens

with a soft cloth or lens cleaning paper and cleaning

fluid (commercially available).

Is the monitor adjusted correctly?

WARNING:

TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

1. Adjust the panning (360˚) and tilt (90˚) position.

2. Set the zoom position by using Zoom Lever Screw.

3. Set the focus by using Focus Lever Screw.

4. Loosen set screws (using small M1.0 Hex L-wrench provided) to adjust

roll (turns camera position top/bottom).

PAN SET

SCREW

(2X)

TILT

90˚ZOOM

FOCUS

SPECIFICATION - VC-700 SERIES

SPECIFICATION - VC-710 SERIES

GENERAL Spec NTSC PAL

CCD Type 1/3" 410K Pixels Color 1/3" 470K Pixels Color

Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)

Scanning System 525 Lines 625 Lines

Horizontal Resolution

Sensitivity to Light [30IRE]

Gamma Correction

Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]

S/N Ratio

Synchronization

Video Output

Control DIP Switch

ME/AE

ATW/AWB

WDR ON/OFF

AGC MAX ON

Electrical Spec

Operating Voltage

Power Consumption

Mechanical Spec

Operation Temp

Air Humidity

Lens Mount

Connections via

DIP Switch Select ATW/AWB (ON/OFF)

DIP Switch Select ME/AE (ON/OFF)

Up to max.90%

14°F ~ 131°F ( -10°C ~ +55°C )

DIP Switch Select ON/OFF

DIP Switch Select WDR (ON/OFF)

BNC(VIDEO), 2P WIRE(Power)

0.45

0.06fC, 0.6Lux(Scene) With F1.2 Lens

480TV Lines

10Vp-p/75ohm Composite

Internal (12VDC) / External (Line Lock, 24VAC)

> 45dB [AGC off]

12VDC -3.9W, 24VAC - 4.0W

12VDC(11-20V), 24VAC(20-27V)

3.3-12mm

GENERAL Spec NTSC PAL

HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470K Pixels Color

Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)

Scanning System 525 Lines 625 Lines

Horizontal Resolution

Sensitivity to Light [30IRE]

Gamma Correction

Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]

S/N Ratio

Synchronization

Video Output

Control DIP Switch

BLC

ME/AE

ATW/AWB

AGC

Electrical Spec

Operating Voltage

Power Consumption

Mechanical Spec

Operation Temp

Air Humidity

Lens Mount

Connections via

14°F ~ 131°F ( -10°C ~ +55°C )

Up to max.90%

3.3-12mm

BNC(VIDEO), 2P WIRE(Power)

DIP Switch Select ATW/AWB (ON/OFF)

DIP Switch Select ON/OFF

12VDC(11-20V), 24VAC(20-27V)

12VDC -2.3W, 24VAC - 2.6W

Internal (12VDC) / External (Line Lock, 24VAC)

10Vp-p/75ohm Composite

DIP Switch Select ON/OFF

DIP Switch Select ME/AE (ON/OFF)

550TV Lines

0.03fc, 0.3Lux(Scene) With F1.2 Lens

0.45

> 48dB [AGC off]

CONNECTIONS

CAUTION

The use of a UL Listed Class 2 power supply is required to ensure

compliance with electrical safety standards.

Check for polarity when using a 12VDC power supply.

12VDC-24VAC

RED (+)

BLACK (-)

11.8in

(300mm

)

RED (+)

BLACK (-)

VIDEO

Cable for connection to portable monitor, provided.

When using a portable monitor, terminate at 75ohms (at last device).

Surface-Mount Base In-Ceiling Base

■CAMERA SETTINGS FOR VC-700 SERIES

(1) Compensating for backlight

ON When back light is too bright

OFF Normal setting

CAUTION : This can also be set correctly by adjusting DC Lens control (5).

(2) Confirming the iris setting

ME The default setting when DC autoiris lens is installed

AE The default seeting when fixed iris lens is installed

CAUTION: The iris setting is preadjusted as the best condition for

use at time of factory shipment; it shouldn't be necessary to change settings.

(3) Confirming the White Balance

(4)Setting gain control (AGC)

For adjusting the sensitivity of the camera. Use this setting

in dark environments.

ON Normal setting

OFF Set this when there is excessive noise

Use this under light source below 2500K and over

9500K of Natrium (Sodium) low color temperature light.

AWC

ATW Use this under light source between 2500K and 9500K

of fluorescent lamp or incandescent light

CAMERA SETTINGS

(1) BLC

(2) ME/AE

(3) AWB

(4) AGC

(5) DC Iris volume

(6) 2nd Video out

(7) Line Lock

(5) Adjusting level volume

If the entire image is too dark or bright, or the backlight

compensation is not correct even after (1) is set to "ON",

adjust the level volume.

CCW (Low) Closes the lens iris, making the entire image darker

CW(High) Opens the lens iris, making the entire image brighter

(6) SECOND VIDEO OUT CONNECTOR

If installer does setting with portable monitor, use this connector.

Be sure to terminate the last device with 75 ohms.

(7) Setting monitor synchronization

(24 VAC adaptor users)

The camera offers V-phase adjustment over 360°. Vertical sync disturbance may occur

when a switcher is used to switch between multiple cameras connected to one monitor.

To prevent vertical sync disturbance, adjust (7) by pushing the button. Before making any

adjustment, confirm that the cameras are connected to the power supply with the same

polarity. To make an adjustment:

While observing the video outputs from the cameras on an oscilloscope, press

the first camera's V-phase pushbutton. Until vertical sync from all cameras are

in phase. If the first camera's adjustment phase is insufficient, adjust the second

camera's V-phase contol in the oppposite direction until they are in phase.

CAUTION

When using the 12 VDC adaptor, sync setting is set to internal sync.

■CAMERA SETTINGS FOR VC-710 SERIES

(1) Confirming the iris setting

ME The default setting when DC auto-iris lens is installed

AE The default seeting when fixed iris lens is installed

CAUTION : The iris setting is preadjusted as the best condition for

use at time of factory shipment; it shouldn't be necessary to change settings.

(1) ME/AE

(2) AWB

(3) WDR

(4) AGC

(5) DC Iris volume

(6) 2nd Video out

(7) Line Lock

(2) Confirming the White Balance

(3) WDR mode

OFF

(4)Setting gain control (AGC)

For adjusting the sensitivity of the camera. Use this setting

in dark environments.

ON Normal setting

OFF Set this when there is excessive noise

(5) Adjusting level volume

If the entire image is too dark or bright, or the backlight

compensation is not correct even after (1) is set to "ON",

adjust the level volume.

CCW (Low) Closes the lens iris, making the entire image darker

CW(High) Opens the lens iris, making the entire image brighter

(6) SECOND VIDEO OUT CONNECTOR

If installer does setting with portable monitor, use this connector.

Be sure to terminate the last device with 75 ohms.

(7) Setting monitor synchronization

(24 VAC adaptor users)

The camera offers V-phase adjustment over 360°. Vertical sync disturbance may occur

when a switcher is used to switch between multiple cameras connected to one monitor.

To prevent vertical sync disturbance, adjust (7) by pushing the button. Before making any

adjustment, confirm that the cameras are connected to the power supply with the same

polarity. To make an adjustment:

While observing the video outputs from the cameras on an oscilloscope, press

the first camera's V-phase pushbutton. Until vertical sync from all cameras are

in phase. If the first camera's adjustment phase is insufficient, adjust the second

camera's V-phase contol in the oppposite direction until they are in phase.

CAUTION

* When using the 12V DC adaptor, sync setting is set to internal sync.

Wide dynamic function is not working

Wide dynamic function is working

AWC Use this under light source below 2500K and over

9500K of Natrium (Sodium) low color temperature light.

ATW Use this under lightsource between 2500K and 9500K of

fluorescent lamp or incandescent light

INSTALLATION

E F

The VC-700 and VC-710 can be either mounted to a surface (like a ceiling or

wall) or installed into the ceiling, with or without an electrical box.

1 Use the large (Torx T20) L-Wrench to loosen the 4 screws (B) securing

the dome assembly.

2 For surface-mount installations, align the mounting base (D) with the

mounting surface; mark the mounting screw holes and then drill the four

holes. For in-ceiling installations not mounting to a 4x4 electrical box,

mark the holes in the camera assembly (C) and then drill the holes. For

in-ceiling installations, (D) is not used.

3 For in-ceiling installations, cut a hole (diameter: 2.9 in./73 mm) in the

ceiling for routing the cables.

4 Route the power cable(s) and video cable(s) to the installation location.

5 Align the four mounting holes in (D) with the holes in the ceiling.

Using the four screws and anchors provided (G), if appropriate for

mounting surface, fasten the mounting base to the wall/ceiling. Using the

other four screws provided, secure the camera assembly (C) to the

mounting base. For in-ceiling installations, align the holes in (C) with

the holes drilled in the ceiling and secure the camera assembly with the

hardware provided, if appropriate. If installing to an electrical box, secure

6 Pass the power cable (E) and video cable (F) from the camera unit

through the cable hole in the ceiling. For surface-mounted units, cabling

is routed through the knockout hole in the side of the unit.

7 Carry out the settings and adjustments for the camera previously

described.

8 Secure the dome assembly (A) by tightening the screws (B).

2.46(R62.5)

2.30(R58.5)

4-0.17(Θ4.3)

2.46(R62.5)

2.30(R58.5)

360˙

Vicon Industries Inc.

Corporate Headquarters

89 Arkay Drive

Hauppauge, New York 11788

USA

631-952-CCTV (2288) 800-645-9116

Fax: 631-951-CCTV (2288)

European Headquarters

Brunel Way

Fareham, PO15 5TX

United Kingdom

+44(0) 1489 566300

Fax: +44(0) 1489 566322

Germany

vin-videotronic infosystems gmbh

Lahnstrasse

D-24539 Neumuenster

Phone: +49 (0) 4321 8790

Fax: +49 (0) 4321 879 47

Internet Address: www.vicon-cctv.com

Vicon Part Number 8009-8178-00-00 Rev 407

Far East Office

Unit 5, 17/F, Metropole Square

2 On Yiu Street, Shatin

New Territories,

Hong Kong

(852) 2145-7118

Fax: (852) 2145-7117

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Vicon Telecamera di sicurezza

Vicon

Vicon I-ONYX MPD-980DN-O Manuale utente

Vicon

Vicon ROUGHNECK V-CELL-HD-B Manuale utente

Vicon

Vicon ROUGHNECK V910 Manuale utente

Vicon

Vicon SN688D-WIR Manuale utente

Vicon

Vicon ROUGHNECK V910 Manuale utente

Vicon

Vicon Roughneck V926 Manuale utente

Vicon

Vicon SurveyorVF SVFT-M Manuale utente

Vicon

Vicon V15CCM-IR-2 Series Rouchneck Manuale utente

Vicon

Vicon I-Onyx MPD-955DN-O Manuale utente

Vicon

Vicon V9360-1 Guida rapida

Vicon

Vicon CE102B Manuale utente

Vicon

Vicon Roughneck Pro V2000B Series Manuale utente

Vicon

Vicon V700W Series Manuale utente

Vicon

Vicon SVR-C Manuale utente

Vicon

Vicon V840D Series Manuale utente

Vicon

Vicon SurveyorVFT SVFT-M Manuale utente

Vicon

Vicon SurveyorVFT SVFT-UPM-1 Manuale utente

Vicon

Vicon V942D-W312MIR Manuale utente

Vicon

Vicon V923-N Manuale utente

Vicon

Vicon Surveyor 4 Manuale utente

Vicon

Vicon Roughneck V2100B Series Manuale utente

Vicon

Vicon Roughneck Pro V2002D-PTZ Manuale utente

Vicon

Vicon Roughneck V2100D Series Manuale utente

Vicon

Vicon Roughneck AI V2000D Series Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente

Lumens

Lumens VC-A50PNW Manuale utente