Viconics VT8600 Series Manuale utente

VT8600 Series Installation Guide

Rooftop Unit, Heat Pump and Indoor Air Quality Controller

VT8600 Series

Installation Guide

Viconics Technologies Inc. www.viconics.com sales@viconics.com

028-0435-03 November 2018

• If replacing an existing Room Controller, label wires before removal of Controller.

• Electronic controls are static sensitive devices. Discharge yourself correctly before manipulating and

installing Room Controller.

• A short circuit or wrong wiring may permanently damage Room Controller or equipment.

• All Room Controllers are designed for use as operating controls only and are not safety devices. Tampering

with the devices or unintended application of the devices will result in a void of warranty.

• This device must be installed to provide a separation distance of at least 8in (20cm) from all persons and

must not be located or operating in conjunction with any other antenna or transmitter.

CLEANING THE ROOM CONTROLLER

• Use a soft, pre-moistened lint-free cloth for cleaning.

• Avoid getting moisture in openings.

• Do not spray anything directly on the Room Controller or use compressed air.

• Do not use caustic/corrosive products, ammonia, solvents or any cleaning product containing alcohol or grit.

• Never use tools directly on the touchscreen.

• Never use paint on the Room Controller.

• Do not drop or crush the Room Controller, or allow the Room Controller to come into contact with liquids.

• Do not use a damaged device (such as one with a cracked screen).

• Performance can be affected if the glass on the screen is broken.

Failure to comply with these recommendations will result in damage to the unit and void the manufacturer’s

warranty.

LOCATION

• Do not install on outside wall.

• Do not install behind a door.

• Do not install in areas with direct heat source.

• Do not install near any air discharge grill.

• Do not install in areas exposed to direct sunlight.

• Ensure Room Controller has sufﬁcient natural air circulation.

• Ensure wall surface is ﬂat and clean.

• Ensure external thermal sensor wirings are away from noisy electrical sources.

• Install 1.3 to 1.5 meter (52 to 60 inches) above the ﬂoor.

VT8600 Series

Installation Guide 3

Figure 1 Open cover

Figure 2 Install base

Figure 3 Reinstall cover

INSTALLATION

1. Remove security screw (if any) on bottom of Room Controller cover.

2. Open unit by pulling on bottom side of Room Controller (Figure 1).

3. Read FCC ID and IC label installed in cover before installing any

wireless product.

4. Ensure correct side of base faces up.

5. Pull cables 6in ( 15cm ) out from wall.

6. Align base and mark location of two mounting holes on wall (Figure 2).

7. Install anchors in wall.

8. Insert cable in central hole of base.

9. Insert screws in mounting holes on each side of base.

10. Strip each wire 1/4in ( 0.6cm) from end.

11. Insert each wire and screw according to wiring chart (next page).

12. Gently push excess wiring back into hole.

13. Gently align cover to top of base and snap in place from bottom

(Figure 3).

14. Install security screw.

Viconics Technologies Inc. www.viconics.com sales@viconics.com

028-0435-03 November 2018

VT8600 Series

Installation Guide

VT86xxU

Description / Application Used in applications

IAQ, HP & RTU

Internal Temperature X

1- BO1 Aux

2- BO2 Y2

3- BO3 Y1

4- BO4 G

5- RC RC (24 Vac)

6- C Common

7- RH RH

8- BO8 W1

9- UO9 W2 / OB

10- UO10 Econo (0-10 Vdc)

11- UO11 Heat (0-10 Vdc)

12- UO12 Dehumidiﬁcation output (24 Vac On/Off)

13- RS485 + BACnet (+)

14- RS485 - BACnet (-)

15- RS485 Ref BACnet Ref.

16- UI16 UI16 (multifunction input)

17- UI17 UI17 (multifunction input)

18- Scom Common

19- UI19 CO2 (0-10 Vdc input)

20- UI20 RS (Remote sensor input 10K thermistor)

21- Scom Common

22- UI22 SS (Supply sensor input 10K thermistor)

23- UI23 OS (Outside sensor input 10K thermistor)

24- UI24 Airﬂow (0-10 Vdc input)

TERMINAL IDENTIFICATION & FUNCTION

REMOTE SENSOR ACCESSORIES

Model Number Description

S3010W1031 Wall mounted temperature sensor

S3020W1031 Wall mounted temperature sensor with override button and occupancy status LED

NOTE:

If one or multiple sensor(s) is/are connected into the RS terminal, the internal temperature sensor is automatically disabled.

Disconnecting the sensor(s) in RS terminal will re-activate the internal sensor.

Remote mount temperature sensors inputs use 10K type 2 NTC thermistors.

Features:

• Each sensor can be conﬁgured for various averaging combinations.

Temperature vs. resistance chart for 10 Kohm NTC thermistor (R25°C = 10KΩ±3%, B25/85°C = 3975K±1.5%)

ºC ºF Kohm ºC ºF Kohm ºC ºF Kohm ºC ºF Kohm ºC ºF Kohm

-40 -40 324.3197 -20 -4 94.5149 032 32.1910 20 68 12.4601 40 104 5.3467

-35 -31 234.4009 -15 571.2430 541 25.1119 25 77 10.0000 45 113 4.3881

-30 -22 171.3474 -10 14 54.1988 10 50 19.7390 30 86 8.0694 50 122 3.6202

-25 -13 126.6109 -5 23 41.5956 15 59 15.6286 35 95 6.5499 55 131 3.0016

Viconics Technologies Inc. www.viconics.com sales@viconics.com

028-0435-03 November 2018

VT8600 Series

Installation Guide 5

TYPICAL APPLICATIONS

VT8600

BO 1 - Aux

BO 2 - Y2

BO 3 - Y1

BO 4 - G

RC (24 Vac)

C (Common)

BO 8 - W1

UO 9 - W2

UO 10 - Econo

UO 11 - Heat

UO 12 - Dehum

BACnet +

BACnet -

BACnet REF

UI 16

UI 17

Common

UI 19 - CO2

UI 20 - RS

Common

UI 22 - SS

UI 23 - OS

UI 24 - Airflow

RTU: 2 Heating Stages / 2 Cooling Stages

13 14 15 16 17 18

7 8 9 10 11 12

19 20 21 22 23 24

1 2 3 4 5 6

ECONO

W2 W1 C R G Y1 Y2

C R

CO2

TRANSMITTER

(0-10 VDC)

OUT

C OUT

AIR FLOW

MEASURING STATION

(0-10 VDC)

FILTER

DPS

SAT

SENSOR

OAT

SENSOR

0-10Vdc

24Vac

Viconics Technologies Inc. www.viconics.com sales@viconics.com

028-0435-03 November 2018

VT8600 Series

Installation Guide

13 14 15 16 17 18

7 8 9 10 11 12

VT8600

BO 1 - Aux

BO 2 - Y2

BO 3 - Y1

BO 4 - G

RC (24 Vac)

C (Common)

BO 8 - W1

UO 9 - W2

UO 10 - Econo

UO 11 - Heat

UO 12 - Dehum

BACnet +

BACnet -

BACnet REF

UI 16

UI 17

Common

UI 19 - CO2

UI 20 - RS

Common

UI 22 - SS

UI 23 - OS

UI 24 - Airflow

RTU: 2 Cooling Stages / Modulating Heat

19 20 21 22 23 24

1 2 3 4 5 6

0-10Vdc

24Vac

ECONO

C R G Y1 Y2

C R

CO2

TRANSMITTER

(0-10 VDC)

OUT

C OUT

AIR FLOW

MEASURING STATION

(0-10 VDC)

FILTER

DPS

SAT

SENSOR

OAT

SENSOR

Mod. Heat

(0-10 VDC)

Viconics Technologies Inc. www.viconics.com sales@viconics.com

028-0435-03 November 2018

VT8600 Series

Installation Guide 7

VT8600

BO 1 - Aux

BO 2 - Y2

BO 3 - Y1

BO 4 - G

RC (24 Vac)

C (Common)

BO 8 - W1

UO 9 - O/B

UO 10 - Econo

UO 11 - Heat

UO 12 - Dehum

BACnet +

BACnet -

BACnet REF

UI 16

UI 17

Common

UI 19 - CO2

UI 20 - RS

Common

UI 22 - SS

UI 23 - OS

UI 24 - Airflow

13 14 15 16 17 18

7 8 9 10 11 12

19 20 21 22 23 24

1 2 3 4 5 6

ECONO

O W C R G Y1 Y2

C R

CO2

TRANSMITTER

(0-10 VDC)

OUT

C OUT

AIR FLOW

MEASURING STATION

(0-10 VDC)

FILTER

DPS

SAT

SENSOR

OAT

SENSOR

HPU: 2 Compressors, Auxiliary Heat and Economizer

0-10Vdc

24Vac

Viconics Technologies Inc. www.viconics.com sales@viconics.com

028-0435-03 November 2018

VT8600 Series

Installation Guide

HOME SCREEN DISPLAY

NOTE:User HMI is conﬁgurable and allows display functions such as Outdoor Temperature, Setpoint, and other buttons to be

enabled or disabled by setting various parameters in the setup screens.

Time

System Status

Fan Status

Up Arrow

Increase Temperature Setpoint

Actual Setpoint

Down Arrow

Decrease Temperature

Setpoint

Help

Language Selection

Temperature Units

Fan Mode

Date

Occupancy Status

Indoor Temperature

Outdoor Temperature

System Mode

Short Network

Message

Typical Hospitality User Interface Shown

Viconics Technologies Inc. www.viconics.com sales@viconics.com

028-0435-03 November 2018

VT8600 Series

Installation Guide 9

HOW TO ENTER SET-UP SCREEN

Touch and hold this point

for 3 seconds to enter set-up mode

SET-UP SCREEN DISPLAY

Return to

home screen

General Note:

1/2 Setup

Network

Configuration

Setpoints - Display

Service View

Test Outputs

Language Selection

Adjustable parameter

Non-adjustable parameter

NOTE: If a conﬁguration/installer

password is activated to prevent

unauthorised access to the

conﬁguration menu parameters,

a password entry prompt shows

to prevent access to device

conﬁguration components.

Enter BACnet®& ZigBee®network settings

Enter parameter conﬁguration menu

Enter setpoint & display settings

Enter output testing mode

Enter status and service view

For more information on using and

conﬁguring the functions of the HMI,

refer to the VT8600 Series User

Interface Guide

Enter language selection

Viconics Technologies Inc. www.viconics.com sales@viconics.com

028-0435-03 November 2018

VT8600 Series

Installation Guide

APPENDIX A TERMINAL CORRESPONDENCE

The terminals of an VT8600 are identiﬁed differently and have a wider range of possible functions compared to those of any of the

VT7000 series Room Controllers. There is a direct correspondence of functions between the terminals of the VT7000 series and the

VT8600 series. Consult the table below to verify the appropriate terminal when replacing a VT7000 Room Controller with a VT8600

Room Controller.

VT7000 VT8600

Terminal name Terminal ID Terminal name Terminal ID

Binary Input 1 BI1 Universal Input 16 UI16

Binary Input 2 BI2 Universal Input 17 UI17

Universal Input 3 UI3 Universal Input 19 UI19

Sensor Common Scom Terminal 18 Common COM

Remote Sensor RS Universal Input 20 UI20 - RS

Sensor Common Scom Terminal 21 Common COM

Mix/Supply Sensor MS Universal Input 22 UI22 - SS

APPENDIX B POWER OUTAGE CLOCK RESET

In the event of a power outage, VT8600 Room Controllers will retain the correct time as long as the duration of the power outage is

not prolonged. Depending on the duration of the power outage, the Room Controller's internal clock may need to be updated or reset

completely. The following table gives an indication of the expected clock performance after a power outage.

Outage duration Room Controller behaviour

0 - 24 hours Clock functions are normal

24 - 36 hours Clock accuracy not guaranteed, time may need to be adjusted

36 - 72 hours Clock no longer increments and must be adjusted when power is

restored

72+ hours Clock functions are fully reset, and must be reinitialized as per a new

installation

Viconics Technologies Inc. www.viconics.com sales@viconics.com

028-0435-03 November 2018

Altri manuali per VT8600 Series

Indice

Altri manuali Viconics Controllori

Viconics

Viconics VT7600E Series Manuale utente

Viconics

Viconics VTR8300 Series Manuale utente

Viconics

Viconics VT7600E Series Manuale utente

Viconics

Viconics VT7200 Series Manuale utente

Viconics

Viconics R851V-4 Manuale utente

Viconics

Viconics VT7225 series Manuale utente

Viconics

Viconics VT7600F Series Manuale utente

Viconics

Viconics VTR8300 Series Manuale utente

Viconics

Viconics R850 Series Manuale utente

Viconics

Viconics VT7225 series Manuale utente

Viconics

Viconics VT76 Series Manuale per l'uso e la cura

Viconics

Viconics VZ7656F1000W Manuale utente

Viconics

Viconics VTR7300 Series Manuale utente

Viconics

Viconics VC3000 Series Manuale utente

Viconics

Viconics R820 REV2 Series Manuale utente

Viconics

Viconics VT8000 Series Manuale utente

Viconics

Viconics VT8000 Series Manuale utente

Viconics

Viconics VT8000 Series Manuale utente

Viconics

Viconics VTR7300 Series Manuale utente

Viconics

Viconics VT7200 F 5000 B Manuale utente

Viconics

Viconics VT8000 Series Manuale utente

Viconics

Viconics VZ8250 Manuale utente

Viconics

Viconics VT8000 Series Manuale utente

Viconics

Viconics VT7600W Series Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente