Viessmann Vitotherm ES4 Guida rapida

Please retain for future use

Installation and service

instructions

for contractors

6167217 GB 11/2020

Vitotherm ES4

Version ES4.A5 K

Version ES4.A5 OK

Version ES4.A5 OTK

Electric water heater

VITOTHERM ES4

6167217 GB

Danger

This symbol warns against the

risk of injury.

These instructions are exclusively

intended for qualified contractors.

Caution

This symbol warns against the

risk of material losses and

environmental pollution.

Note

Details identified by the word "Note"

contain additional information.

Safety instructions explained

Target group

For your safety

Safety instructions

■National installation regulations

■Statutory regulations for the

prevention of accidents

■Statutory regulations for

environmental protection

■Codes of practice of the relevant trade

associations

Regulations to be observed

■Work on electrical equipment must

only be carried out by a qualified

electrician.

■The system must be commissioned

by the system installer or a qualified

person authorised by the installer.

■Relevant safety regulations

■Requirements stipulated by the local

power supply utility

■Requirements stipulated by the local

water company

Before installing, commissioning and operating the appliance, please read the

documents enclosed with the appliance.

Follow the safety instructions closely to prevent hazards, injury and material

losses.

Store the supplied documents in a safe place.

6167217 GB

For your safety (cont.)

Installation work

Safety instructions

Danger

Contact with live components can

result in severe injuries. Some

components remain live even after

the power supply has been

switched off. Wait at least 4 minutes

for the voltage to discharge before

removing the appliance covers.

Safety instructions for working on the appliance

Danger

Hot surfaces and fluids can cause

burns.

■Switch off the appliance and

allow it to cool down before

carrying out any maintenance

work.

■Do not touch hot surfaces on the

appliance, fittings or pipes.

■Switch off the power supply, e.g. at

the separate fuse or a mains isolator.

■Safeguard the power supply against

reconnection.

■ Check that it is no longer live.

■Do not make any modifications to the

water or electrical installations.

■Do not make any structural

modifications to the appliance.

Maintenance work

■

Only install the appliance on a suitably

stable wall with the fixing materials

provided.

■Do not make any structural

modifications to the appliance.

■Install an isolator in the power cable

to provide omnipolar separation from

the mains for all active conductors,

corresponding to overvoltage

category III (3 mm) for full isolation.

The isolator must be fitted in the

permanent electrical installation, in

line with installation requirements.

We also recommend installing an

RCD (Class A) for pulsating DC (fault)

currents.

■The appliance must be connected to

the power supply via a dedicated fixed

socket. The power cable and fuse

must be sized appropriate to the

output of the appliance.

■This appliance of protection class I

must be permanently connected to

the earth conductor.

■Provide protection against contact

with live parts. Install covers.

6167217 GB

Caution

Repairing components that fulfil a

safety function can compromise the

safe operation of the appliance.

Replace faulty components only

with genuine Viessmann spare

parts.

Repair work Auxiliary components, spare parts

and wearing parts

Caution

Spare parts and wearing parts that

have not been tested together with

the appliance can compromise its

function.

Installing non-authorised

components and making

non-approved modifications or

conversions can compromise safety

and may invalidate our warranty.

■For replacements, only use

original Viessmann parts or spare

parts approved by Viessmann.

■For appliances with a power

cable, use only original

Viessmann spare parts.

For your safety (cont.)

Safety instructions

Danger

If there are leaks in the appliance,

there is a risk of electric shock.

■Isolate the appliance from the

power supply e.g. At the

separate fuse or by means

of a mains isolator.

■Close the cold water supply

shut-off valve.

Safety instructions for operating the device

If water escapes from the appliance

Danger

If water escapes from the

appliance, there is a risk of

scalding.

Never touch hot water.

■Only operate the appliance after it has

been properly installed on the wall.

■ Comply with the permissible operating

data, as specified on the type plate.

Operation of the appliance

6167217 GB

Table of contents

1. Information Disposal of packaging .....................................................................6

Intended use....................................................................................6

Product information .........................................................................6

2. Installation

sequence

Installation .......................................................................................7

■

Connection to the water system

..................................................... 7

■

Installation with safety valve for pressure-tested installation

....... 8

Wiring diagram ................................................................................9

Electrical installation......................................................................10

3. Maintenance Operation....................................................................................... 11

■Switching on............................................................................... 11

■Temperature control ................................................................... 11

■Venting .......................................................................................12

■Faults..........................................................................................12

Removing the cover.......................................................................13

List of spare parts..........................................................................14

4. Appendix Specification ..................................................................................15

Table of contents

6167217 GB

Disposal of packaging

Information

Please dispose of packaging waste in line

with statutory regulations.

Intended use

Product information

The appliance is used for the heating of

domestic hot water and can supply one or

more draw-off points as applicable.

The appliance is intended for domestic use.

It can be operated safely by untrained

persons. The appliance can also be used

in a non-domestic environment, e.g. in a

small business, as long as it is used in the

same way.

Any use that differs from or goes beyond this

is considered inappropriate.

Intended use also extends to compliance with

these instructions and with the instructions for

any accessories used.

Electric water heater for pressurised or

non-pressurised installation.

Max. water pressure in system: 0.6 MPa

■Corrosion-resistant stainless steel

cylinder

Anode does not need to be replaced on a

regular basis.

■Efficient heating module

Output: 2000 W

DHW heating from 10 to 40 °C in 5.5 min

for 5 l

■

Energy efficiency class A

Very low energy loss.

■ Functional temperature control

Water temperature can be variably

adjusted between 23 and 70 °C

Types of installation

Types ES4.A5 OK and ES4.A5 OTK:

Appliances for installation above a washbasin

with water connections pointing vertically

downwards.

Type ES4.A5 K:

Appliances for installation below a washbasin

with water connections pointing vertically

upwards.

Note:

In a pressurised installation, water may

occasionally escape from the safety valve.

In a non-pressurised installation, water may

occasionally escape from the hot water

draw-off point.

This is not a malfunction.

Any water that occasionally escapes must be

able to drain away freely at all times.

6167217 GB

Installation

Installation sequence

Connection to the water system

Shutting off the cold water supply will cause

the appliance to malfunction.

Non-pressurised installation:

• Fit the hot water tap over a basin with

a drain.

• Do not install any devices between the

hot water outlet of the appliance and the

water outlet of the fitting which could

inhibit the flow. A free outflow of water

must be guaranteed at all times.

Pressurised installation:

• For system water pressures above

0.6 MPa, a pressure reducing valve must

be installed upstream of the safety valve

on the cold water supply.

• Connect the safety valve to a drain line.

• The safety valve and the outlet line must

not be installed in rooms where

temperatures below 0 °C occur.

• Do not install a shut-off valve between the

safety valve and the electric water heater.

Type ES4.A5 OTK:

■

Install only with water connections

pointing vertically downwards.

■

Only connect the fitting that has been

supplied with this appliance.

■

A pressure reducer and safety valve are

not required as the appliance is only

operated as a non-pressurised system.

Fastening with rawl plugs:

1. Insert two 8 mm diameter rawl plugs into

the wall 140 mm apart

2. Screw in the fixing screws until the

clearance between the screw head and

the wall is no more than 4 mm.

3. Hang the electric water heater on the

screws.

Fastening with wall mounting bracket:

1. Fit the wall mounting bracket.

2. Hang the electric water heater on the wall

mounting bracket and secure it in place

with the fixing screws.

For type ES4.A5 OTK, a clearance must

be maintained between the fixing screws

and the fitting.

Fit the appliance to a stable wall in a vertical

position. Connections are at the top or bottom,

depending on the type.

6167217 GB

Installation sequence

1. Prepare the cold water supply according

to local regulations and connect to the

appliance:

Types ES4.A5 OK and ES4.A5 K:

Connect the cold water pipe to the inlet

connector and the DHW outlet to the

outlet connector: See adjacent diagrams.

It is essential that a safety valve [6] with

a nominal pressure of 0.6 MPa is installed

in the cold water supply.

Type ES4.A5 OTK:

Insert gaskets into the nuts and connect

the fitting to the appliance using metal

pipes or flexible hoses. Recommended

distance between metal pipes and wall:

~34 mm.

2. Route the drain line for the safety valve

downwards, ensuring it is located in a

frost-free environment.

3. Open the hot water tap (red) and fill the

integral cylinder completely with water

(water must run out of the hot water tap

free of bubbles).

4. Check connections for tightness.

Installation with safety valve for pressure-tested installation

Type ES4.A5 OK must be installed with

connections pointing vertically downwards.

Type ES4.A5 K must be installed with

connections pointing vertically upwards.

3 Inlet connector (cold water)

4 Outlet connector (DHW)

5 DHW outlet

6 Safety valve

7 Pressure reducing valve (for system

water pressures above 0.6 MPa)

8 Shut-off valve

9 Cold water supply

6167217 GB

Installation sequence

Wiring diagram

E1 – Heating module

F1 – Thermal circuit breaker

K1 – Thermostat

X1 – Terminal strip

XP – Power cable

H1 – Heating display

6167217 GB

Installation sequence

Electrical installation

Altri manuali per Vitotherm ES4

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Viessmann Scaldabagno

Viessmann

Viessmann VITOCELL 100-VH Manuale

Viessmann

Viessmann VITOWELL EASY C1 Manuale utente

Viessmann

Viessmann Vitocell 100-E Guida rapida

Viessmann

Viessmann Vitotherm ES4.A10 K Guida rapida

Viessmann

Viessmann Vitocell-V 100 200 Manuale utente

Viessmann

Viessmann VITOCELL-V 100 Manuale utente

Viessmann

Viessmann Vitodens 111-W Guida rapida

Viessmann

Viessmann Vitosol 100 Manuale utente

Viessmann

Viessmann VITOCELL 300V Manuale utente

Viessmann

Viessmann VITOCELL 300B Manuale utente

Viessmann

Viessmann VITOCELL 300V Guida rapida

Viessmann

Viessmann Vitocell 100-E Guida rapida

Viessmann

Viessmann Vitocell 100-E SVW 200 l Guida rapida

Viessmann

Viessmann VITOCELL 300V Manuale di istruzioni

Viessmann

Viessmann VITOCELL 100-B Manuale utente

Viessmann

Viessmann Solar-Divicon-HX Dimensioni e guida di installazione

Viessmann

Viessmann VITOCELL 100-B Istruzioni operative

Viessmann

Viessmann Vitocell 140-E Istruzioni operative

Viessmann

Viessmann Vitocell 140-E Guida rapida

Viessmann

Viessmann OpenTherm Istruzioni operative

Viessmann

Viessmann VITOCELL 300W Manuale di servizio

Viessmann

Viessmann VITOTRANS 300 Manuale utente

Viessmann

Viessmann VITOCELL 300B Istruzioni operative

Viessmann

Viessmann VITOTHERM EI5 Series Manuale utente

Manuali Scaldabagno popolari di altre marche

Kenmore

Kenmore 153.582400 Manuale utente

Applimo

Applimo Edel AIR Manuale utente

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Manuale utente

clage

clage E-Mini Series Manuale utente

Toyotomi

Toyotomi Oil Miser OM-180 Manuale utente

Bradford White

Bradford White EF Series Manuale utente

Eccotemp

Eccotemp 40-H Manuale utente

Dimplex

Dimplex ECSd125-580 Guida

Dux

Dux 32FCR6N Manuale utente

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Guida alla risoluzione dei problemi

Noritz

Noritz N-132M Manuale di istruzioni

TESY

TESY GCV7/4S 10047 Scheda tecnica

A.O. Smith

A.O. Smith Gphe 50 Manuale utente

Koryo

Koryo KWHZF15Y Manuale utente

Pentair

Pentair PSC-14-4-02 Manuale utente

GE 40M06AAG Istruzioni per il montaggio

Thermor

Thermor AEROMAX SPLIT 2 Manuale utente

American Hometec

American Hometec AHQ-B03X Manuale utente