Vision Express S5 Manuale utente
© 2018 Vision Engraving & Routing Systems
Vision Express Engraver S5
Installation Guide
Revised: 11/5/2018Part number 12-1084-01
All rights reserved. No parts of this work maybe reproduced in anyform or byanymeans - graphic, electronic, or
mechanical, including photocopying, recording, taping, or information storage and retrieval systems - without the
written permission of the publisher.
Products that are referred to in this document maybe either trademarks and/or registered trademarks of the
respective owners. The publisher and the author make no claim to these trademarks.
While everyprecaution has been taken in the preparation of this document, the publisher and the author assume no
responsibilityfor errors or omissions, or for damages resulting from the use of information contained in this
document or from the use of programs and source code that mayaccompanyit. In no event shall the publisher and
the author be liable for anyloss of profit or anyother commercial damage caused or alleged to have been caused
directlyor indirectlybythis document.
Revised: 11/5/2018
Vision Express Engraver S5 Installation
Guide
© 2018 Vision Engraving & Routing Systems
3Contents
3
© 2018 Vision Engraving & Routing Systems
Table of Contents
Part I Introduction 4
................................................................................................................................... 51 Computer Requirements
................................................................................................................................... 62 General Electrical and Facility Requirements
................................................................................................................................... 63 Vision ExpressEngraver Installation Layout
Part II Vision Software Installation 7
Part III Machine Setup 18
................................................................................................................................... 201 Direct Connection to Computer
................................................................................................................................... 262 Network Connection
Vision Express Engraver S5 Installation Guide4
© 2018 Vision Engraving & Routing Systems
1 Introduction
This guide contains information to prepare the new owner of a Vision Express for the proper installation of
their machine. It is the customer's responsibility to read through this guide and make sure the work area,
electrical and computer requirements are met. If for any reason, there are questions about these
requirements, please call your Vision representative as soon as possible.
In the following sections, the complete machine and Vision software installation will be outlined.
Please call your distributor or the service department at Vision for assistance if you have any questions
with this procedure.
FOR MORE DETAILED INFORMATION, PLEASE REFER TO THE USER GUIDE FOR YOUR MACHINE
INSTALLED WITH THE VISION SOFTWARE. USER GUIDES ARE ALSO AVAILABLE ONLINE AT
http://www.visionengravers.com/support/vision-engraver-manuals.html
Important Note:
The Vision software is available in two versions; one with a dongle, and one
that is "dongle-less" and is loaded on to a USB Memory stick. If your machine
was delivered with, or you currently have the white/blue or orange software
dongle, DO NOT LOSE IT!
The Vision software will NOT run without the dongle plugged into the computer.
Introduction 5
© 2018 Vision Engraving & Routing Systems
1.1 Computer Requirements
Minimum System
Requirements:
CPU:
Dual Core (2.0GHz or higher)
Hard Drive:
750 GB free space
RAM:
1GB + OS Requirements
Operating System:
Windows 10 (32/64 bit)
Windows 8 (32/64 bit)
Windows 7 SP.1 (32/64 bit) ***Requires Service Pack 1
Ports:
USB port for security dongle
Local or network Ethernet port to connect machine
Suggested System
Requirements
CPU:
Core i3 (or faster)
Hard Drive:
1 TB (or more)
RAM::
4GB + OS Requirements
Operating System:
Windows 10 (32/64 bit)
Windows 8 (32/64 bit)
Windows 7 SP.1 (32/64 bit) ***Requires Service Pack 1
Ports
USB port for security dongle
Local or network Ethernet port to connect machine
Vision Express Engraver S5 Installation Guide6
© 2018 Vision Engraving & Routing Systems
1.2 General Electrical and Facility Requirements
Machine Model
Requirements
Express
One 110 VAC 15 Amp or One
220 VAC 10 Amp Single Phase
Optional Equipment
Engraving Vacuum Chip Removal System
One 110 VAC 15 Amp
NOTE: In addition to the above requirements, a standard outlet is required for the
computer.
1.3 Vision Express Engraver Installation Layout
Vision Express Engraver Installation Layout
Introduction 7
© 2018 Vision Engraving & Routing Systems
2 Vision Software Installation
Insert the Vision USB dongle into the USB port on the computer. Navigate to the Devices and Drives
area on your PC. Double click on the Vision icon to open the files on the USB dongle.
Select the Start or Start.exe file to begin.
Click on the Install Vision Software button.
Vision Express Engraver S5 Installation Guide8
© 2018 Vision Engraving & Routing Systems
The Vision S5 Software Wizard will guide you through the process of installing the software. Press Next
to continue.
Press Install to continue
Vision Software Installation 9
© 2018 Vision Engraving & Routing Systems
Setup wizard will install the program.
Select Finish to continue the software installation.
Choose your preferred language and click ok.
Vision Express Engraver S5 Installation Guide10
© 2018 Vision Engraving & Routing Systems
The Vision 10 Setup Screen will appear. Press Next.
After accepting the license agreement, click on the Next button.
Altri manuali per Express S5
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Vision Incisore
Vision
Vision VE810 4 Series Manuale utente
Vision
Vision MAX Pro Manuale utente
Vision
Vision Multi Axis Manuale utente
Vision
Vision 1612 Manuale utente
Vision
Vision SP Series Manuale utente
Vision
Vision VE-810 Manuale utente
Vision
Vision MaxPro Manuale utente
Vision
Vision 5 Series Manuale utente
Vision
Vision 1624R Manuale utente
Vision
Vision Express S5 Manuale utente
Vision
Vision PHOENIX TABLE Manuale utente
Vision
Vision MAX Pro Manuale utente
Vision
Vision VE810 S5 Manuale utente
Vision
Vision Phoenix 1212 Manuale utente
Vision
Vision 16 Series Manuale utente
Vision
Vision Phoenix 1212 S5 Manuale utente
Vision
Vision 5 Series Manuale utente
Vision
Vision Cylindrical Manuale utente
