Vitek VTC-TNT30R3F Manuale utente

VITEK

FEATURES

• 1/3” 3.0 Megapixel Progressive Scan CMOS image sensor

• Up to 30fps live view @ 1920x1080 (2MP) / 15fps live

view @ 2048x1536 (3MP)

• 2.8~12mm Varifocal Lens (VTC-TNT30R3V) / 3.6mm

Fixed Iris Lens (VTC-TNT30R3F)

• 30 Infrared LED’s with 100’ IR Range

• Wide Dynamic Range (WDR)

• True Mechanical Day/Night function by ICR

• 3D-DNR Noise Reduction

• On Board Motion Detection

• H.264/MJPEG Dual Streaming

• Onvif Compliance

• Remote Viewing via CMS, Web Browser, and iOS & Android

Apps

• Minimal Latency with up to 10 simultaneous user

connections

• IP66 Weather Resistance

• 12VDC & PoE (Power over Ethernet) Operation

VTC-TNT30R3F

VTC-TNT30R3V

3.0 Megapixel Indoor/Outdoor

WDR IP IR Turret Cameras

QUICK START GUIDE

*Refer to included CD for complete detailed User’s Manual.

2 3

Overview

Components and Accessories

Camera

Quick Guide

Screws

Hex Wrench

Drill Template

Product Manual CD

Waterproof Cap

Focus

Zoom

This camera series supports both fixed and varifocal lenses. Please note

that the zoom and focus features mentioned below are not features of the

fixed lens version.

Focus

Zoom

*Optional

Lens

Focus*

Zoom*

Lock Screws

RJ-45 Ethernet

Power Cable

Focu s

Zoom

Fo c u s

Zo o m

Network Cable & Power Connections

Cable / Network Configuration

First connect the Waterproof Cap to an Ethernet patch cable, then

connect the cameras ethernet adaptor. If not powering the camera with

PoE, also connect the power Cable to an approved 12VDC Power

Supply.

12VDC

Optional 12VDC

Power Connection.

Not needed with PoE

12VDC

Router

Internet

Modem

Computer

Network Cable

4 5

Installation

Before start, please make sure that the wall or ceiling is strong enough

to withstand 3 times the weight of the camera. The mounting steps are

as follows:

1. Attach the drill template to

the place where you want to

install the camera, then drill

3 screw holes and 1 cable

hole (if you want to route the

cables through the mounting

base) according to the drill

template

2. Route the cables and

connect the power & video

cables, then secure the

mounting base to the ceiling

or wall with screws.

3. Loosen the lock screws, then

adjust the camera to obtain

the optimium viewing angle.

Confirm the correct viewing

angle with a monitor. (See

next page for location of lock

screws)

Fo c u s

Zoom

Installation

4. Tighten the lock screws to secure the viewing angle adjustments.

5. Adjust the Focus and Zoom screws to achieve a clear image (if

your camera has a fixed lens, please skip this step).

6. Carefully remove the protective film from the lens to complete the

installation.

Focus

Zoom

Fo cu s

Fo c us

Zoom

Foc u s

Zo o m

Zo om

Fo c u s

Zoo m

6 7

LAN Configuration

The camera can be accessed on the local network either using the

IP-Tool or directly in a web browser.

1. Attach the drill template to the place where you want to install the

camera, then drill 3 screw holes and 1 cable hole (if you want to

route the cables through the mounting base) according to the drill

template

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.

2. Locate the IP-Tool installer on the included Product Documentation

CD, then install on the PC. Open the installed application.

3. Modify the IP address. The default IP address is 192.168.226.201.

Click the information of the camera listed in the above table to show

the network information on the right side. Modify the IP address and

gateway of the camera and make sure its network address is in the

same local network segment as the computer’s. Please modify the

IP address of your device according to the practical situation.

For example, the IP address of your computer

is 192.168.13.4. So the IP address of the

camera shall be changed to 192.168.13.X.

After modification, please input the password

of the administrator and click “Modify” button

to modify the setting.

** Default admin password: “123456".

4. Double-click the IP address and then the system will pop up the web

browser to connect IP-CAM . IE browser will download the Active X

control automatically. After downloading, a login window will pop up

as shown below:

Input the user name and password to log in.

Default user name: admin / Default password: 123456.

Directly Access Through a Web Browser

The default network settings are as shown below:

IP address: 192.168.226.201 HTTP: 80

Subnet Mask: 255.255.255.0 Data Port: 9008

Gateway: 192.168.226.1

You may use the above default settings when you log in the camera for

the first time.

1. Manually set the IP address of the PC and the network segment

should be as the same as the default settings of IP-CAM. Open the

network and share center. Click “Local Area Connection” to pop up

the following window.

Select “Properties” and then select Internet protocol according to the

actual situation (for example: IPV4). Next, click “Properties” button to

set the network of the PC.

2. Open the IE Browser and input the default address of IP-CAM and

confirm. The IE browser will download Active X control automatical-

ly.

3. After downloading Active X control, the login dialog box will pop up.

4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the

camera via LAN and go to System Congfig→Network Config→Port

menu to set up the port number.

2. Enter System Config→Network Config→IP Address menu to modify

the IP address.

4. Open the web browser and input its WAN IP and HTTP port to

access the IP-CAM.

3. Go to the router’s management interface through IE browser to

forward the IP address and port of IP-CAM in the “Virtual Server”.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Vitek Telecamera di sicurezza

Vitek

Vitek Transcendent VTD-TND8RMS Manuale utente

Vitek

Vitek VTC-C544 Manuale utente

Vitek

Vitek VTD-TND4RFA4 Manuale utente

Vitek

Vitek VTD-MH2910 Manuale utente

Vitek

Vitek VTD-HOCR2812 Manuale utente

Vitek

Vitek VTD-VPH266 Manuale utente

Vitek

Vitek VT-PTZ40WH Manuale utente

Vitek

Vitek Alpha VTD-A4F/I Manuale utente

Vitek

Vitek VIRTUOSO Manuale utente

Vitek

Vitek VTC-EB25C Manuale utente

Vitek

Vitek VTC-IRLED30A Manuale utente

Vitek

Vitek VT-IR1B/24 Manuale utente

Vitek

Vitek Alpha Series Manuale utente

Vitek

Vitek VTC-C770WS Manuale utente

Vitek

Vitek VTC-C01 Manuale utente

Vitek

Vitek Transcendent Series Manuale utente

Vitek

Vitek VTC-TNT4RMAD Manuale utente

Vitek

Vitek VT-PIRC1 Manuale utente

Vitek

Vitek Transcendent VTD-TND8RMEA Manuale utente

Vitek

Vitek TRANSCENDENT VTC-TNB4LPRN Manuale utente

Vitek

Vitek XPRESS SERIES Manuale utente

Vitek

Vitek VT-TPTZ25HRAN-8PNL Manuale utente

Vitek

Vitek VTC-C770/WDR Manuale utente

Vitek

Vitek VTD-TNMD4RFS Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Lumens

Lumens VC-A50PNW Manuale utente