Vitek VTC-TTAT2HR2F Manuale utente
VITEK
VITEK
FEATURES
• 1/3” 2.1 MegaPixel CMOS Sensor
• HD-TVI & AHD/CVBS Video Output
• 2.8~12mm Varifocal Lens (VTC-TTAT2HR2V) or 3.6mm
Fixed Lens Options (VTC-TTAT2HR2F)
• 2 High Power Infrared LED’s with 100’ IR Range (VTC-
TTAT2HR2V) / 65’ IR Range (VTC-TTAT2HR2F)
• Digital Wide Dynamic Range (D-WDR)
• True Mechanical Day/Night function by ICR
• 3D-DNR Noise Reduction
• IP66 Weather Resistance
• Supports Up The COAX Control
• Over 1500’ HD Video Transmission (Depending on cable
characteristics and integrity)
• Optional Junction Box Mount Available (VT-TJB01) / Wall
Mount (VT-TWM03) Also Available for VTC-TTAT2HR2V
• 12VDC Operation
VTC-TTAT2HR2F
VTC-TTAT2HR2V
2.1 Megapixel Outdoor HD-TVI/
AHD/CVBS IR Turret Cameras
2 3
Safety Precaution
CAUTION: TO REDUCE THE RISK OF ELECTICAL
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
To prevent electrical shock and risk of fire hazards, do not expose this unit
to rain or moisture and only use specified power source..
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
their own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Main power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power interruptions, it is
recommended that the device be powered from an uninterruptible power supply
(UPS).
The symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electrical shock.
3
Components and Accessories
Overview
This camera series supports both fixed and varifocal lenses. Please note
that the zoom and focus features mentioned below are not features of the
fixed lens version.
Focus
Zoom
3
4
1
2
5
6
7
8
Lens
Focus*
Zoom*
Lock Screws
Power Cable
AHD/CVBS Switch
AHD/CVBS Output
HD-TVI Output
1
2
3
4
5
6
7
8
*VTC-TTAT2HR2V Only
Focus
Zoom
Camera
User Manual
Screws
Hex Wrench
Mounting Plate
4 5
Video Connection
Monitor
Video
Fo cus
Zo om
Power
12VDC
Fo cus
Zo om
Power Connection
Connect the power connecter to a 12 VDC power adaptor.
Connect the HD-TVI Video or AHD/CVBS video connector to a BNC
patch cable, then to DVR.
AHD/CVBS Switch:
Switch to CVBS Mode: Press & Hold the Switch for 5 seconds
Switch to AHD Mode: Press & Release the Switch quickly
5
Installation
Before you begin, please make sure that the wall or ceiling is strong
enough to withstand 3 times the weight of the camera. The mounting
steps are as follows:
1. Attach the drill template to
the place where you want to
install the camera, then drill
3 screw holes and 1 cable
hole (if you want to route the
cables through the mounting
base) according to the drill
template
.
2. Route the cables and
connect the power & video
cables, then secure the
mounting base to the ceiling
or wall with screws.
3. Loosen the lock screws, then
adjust the camera to obtain
the optimium viewing angle.
Confirm the correct viewing
angle with a monitor. (See
next page for location of lock
screws)
Fo c us
Zoom
6 7
Installation
4. Tighten the lock screws to secure the viewing angle adjustments.
5. Adjust the Focus and Zoom screws to achieve a clear image (if
your camera has a fixed lens, please skip this step).
6. Carefully remove the protective film from the lens to complete the
installation.
Focus
Zo o m
Foc us
Fo cus
Zoom
Foc u s
Zo om
Zoo m
Fo c u s
Zoom
7
Camera OSD Menu
The following menu toolbar will pop up by right-clicking the mouse
when using VITEK Transcendent Series HD-TVI DVRs.
The Transcendent HD-TVI/AHD camera series must be connected to a
DVR which supports HD-TVI/AHD video signal input and COC protocol
to access the OSD setup menu. Different DVRs manufacturers may
have different modes of menu operation.
You will see the following interface by clicking the button.
Click “Iris +” to go to the main menu. You can also select preset NO.
95, then click the button（call preset NO.95）to go to the follow-
ing main menu.
8 9
You can select the menu by clicking (U) or (D) key on the
direction area. Click (L) or (R) key to select the menu on the
left. The menu with arrow icon which means it has sub-menu. You
can select the menu and click “Iris +” or call preset NO.95 to enter
the sub-menu. To return to the previous menu or exit the main
menu, please select “RET” or “Save & END” by clicking U or D key
and then click “Iris +” or call preset NO.95.
9
Detailed Specifications VTC-TTAT2HR2F VTC-TTAT2HR2V
Image Sensor
Resolution
Effective Pixels
Signal System
Video Output
Lens
Day/Night
S/N Ratio
Auto Gain Control
Min Illumination
IR LEDs
IR Distance
Color-B/W Auto Switch
Electronic Shutter
White Balance
WB Range
BLC
WDR
Transmission Distance
Up the COAX Control
Noise Reduction
Weather Resistance
Power Supply
Working Environment
Weight
Dimensions
1/3” 2.1 MegaPixel CMOS Sensor
1080p (2.1 MegaPixel)
1920(H) x 1080(V)
PAL/NTSC
1x HD-TVI (BNC) & 1 AHD/CVBS (BNC)
True Day/Night by ICR
>52dB (AGC OFF)
OFF ~ 44.8dB
0 Lux (LED ON)
Yes
1/50s~ 1/67500s
AWB
2300~9600K
Yes
Digtial WDR
Up to 1500’ (Depending on cable characteristics & integrity)
YES
Yes
IP66
12VDC
-4~122 / 10%~90% Humidity
3.6mm Fixed
2 x High Power
65’
13.05 oz. / 0.82 lbs. / 370g
3.43” x 4.25” (87 × 108mm) Dia x H
2.8~12mm (Vari-Focal)
2 x High Power
100’
24.30 oz. / 1.52 lbs. / 689g
4.29” x 5.12” (109 × 130mm) Dia x H
10 11
VT-TWM03
Wall Mount for Transcendent
30 IR LED Vandal Domes and
Varifocal Turret Cameras
OPTIONAL ACCESSORIES FOR
TRANSCENDENT CAMERAS
VT-TR4K
Passive Video Balun Transmitter/
Receiver pair (2ea included) for
TVI/AHD/CVI for distances from
680 to 1400’. Built in Surge
suppression and 60dB noise
immunity
VT-TR4VPK
Video & Power Balun
Transmitter/Receiver pair (2ea
included) for TVI/AHD/CVI for
distances from 680 to 1400’.
Built in Surge suppression and
60dB noise immunity
VT-TJB01
Optional Junction Box for Cable
Management for use with all
Transcendent Bullet and Turret
Style Cameras
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Vitek Telecamera di sicurezza
Vitek
Vitek VT-PIRC2H Manuale utente
Vitek
Vitek VTC-T4T3HR2MD Manuale utente
Vitek
Vitek VTC-IRT40-2812 Manuale utente
Vitek
Vitek VTC-IR1600 Manuale utente
Vitek
Vitek VTC-C2NZ Manuale utente
Vitek
Vitek Virtuoso Series 8 Manuale utente
Vitek
Vitek VTC-C770WS Manuale utente
Vitek
Vitek VTC-IR62NZ922 Manuale utente
Vitek
Vitek VTD-MD5CH Manuale utente
Vitek
Vitek Transcendent Series Manuale utente
Vitek
Vitek VTC-TNT4RFS Manuale utente
Vitek
Vitek VTD-T4D6HR2MD Manuale utente
Vitek
Vitek Transcendent VTC-TNB8RFEA-2 Manuale utente
Vitek
Vitek VIRTUOSO Manuale utente
Vitek
Vitek Alpha Series Manuale utente
Vitek
Vitek VTC-C2BAZE Manuale utente
Vitek
Vitek VTC-TNT2HR3F2 Manuale utente
Vitek
Vitek VTC-HD713A Manuale utente
Vitek
Vitek Transcendent VT-TPT23HR-WM Manuale utente
Vitek
Vitek VTD-TND5RMS Manuale utente
