Vivotek FD8335H Manuale utente

EN - 1

English

Power off the Network Camera as

soon as smoke or unusual odors are

detected.

Contact your distributor in the event of

occurrence.

Refer to your user's manual for the

operating temperature.

Warning Before Installation

Do not place the Network Camera on

unsteady surfaces.

Do not touch the Network Camera

during a lightning storm.

Do not insert sharp or tiny objects

into the Network Camera.

Do not drop the Network Camera.

EN - 2

Software CD

FD8335H

Quick Installation Guide /

Warranty Card

Alignment Sticker /

Ceiling Hole Template Sticker

Mounting Plate

Package Contents

L-type Hex Key Wrench / Moisture

Absorber / Screws / Hex Nut / Double-

sided Tape / AV Cable

Waterproof Connector & Bushing

EN - 3

English

IR LEDs (18 units, effective up

to 15m)

Physical Description

Inner View Lens

Tilt Adjustment Screw

Black Cover

1. There is no internal microphone. Only external microphone is applicable.

2. The Focus Assist button takes effect when using a hand-held monitor or camera

tester with a BNC connector. Press the button and use the focus and zoom

adjustment pullers to tune the image until the "BEST FOCUS" message is

shown.

Ethernet 10/100

RJ45 Socket

Audio/Video

Out (green)

Microphone In

(pink) General I/O Terminal

Block

Jumpers

Microphone Video Output

Internal

External

NTSC

60Hz

PAL

50Hz

Micro SD/SDHC Card Slot

Reset

Button

Focus Assist Button

LCD Monitor/

Camera tester

AV Out

Focus Assist

Button

EN - 4

First, use the included T20 hex key wrench to loose the four screws and detach the dome cover from the

camera base. Follow the steps below to install the camera either to a ceiling or a wall.

Hardware Installation

Top View Dome Cover

Dome Cover Retainer

IMPORTANT! Dome cover should be removed because if it should fall during the installation

process, physical injury could occur to your co-workers.

Record the MAC address

under the camera base

before installing the camera.

Replace the side opening cover with the

included side outlet bushing if you want to

route cables from the side of camera. The 1/2"

protection conduits and tubing are separately

purchased.

EN - 5

English

Connect power lines and if you have external devices such as sensors and alarms, make the connection

from the general I/O terminal block.

87654321

Cabling Assembly

Pin Denitions

1 AC24V_2

2 AC24V_1

3 DI3+

4 DI2+

5 DI1+

6 DI-

7 DO-

8 DO+ (12V)

For Ethernet

Cable For Power & IO Cables

Top View

Power and IO cables pass through a waterproof connector. The

Ethernet cable should be routed through a rubber seal plug. All

cables are user-supplied.

1. Disassemble the components of the waterproof

connector into parts (A) ~ (F) as shown above.

2. Place the screw nut (E) on the Power and GPIO

opening.

3. Feed the power cables through the waterproof

connector (F --> E --> D --> B --> A) as the

illustration shows. Then connect the power

cables to the power source. Note: There are 8

holes on the seal (D), and the widest holes with

a crack on the side are specic for power cables.

4. If you have external devices such as sensors

and alarms, feed the cables through the

Assembling Steps

Sealing Nut (A)

Housing (B)

Seals (C)

Seal (D)

Screw Nut (E)

Hex Nut (F)

Waterproof Connector (A)

(B)

(D)

(E)

(F)

waterproof connector (F --> E --> D --> B -->

A) as previously described. Refer to the pin

definition to connect them to the general I/O

terminal block. Note: The recommended cable

gauge is 2.0 ~ 2.8 mm.

5. Push the seal (D) into the housing (B).

6. Insert the seals (C) into unused holes on the

seal (D) to avoid moisture.

7. Secure the sealing nut (A) tightly and hex nut

(F) from the bottom of the camera.

EN - 6

RJ45 Cable Dimension (unit: mm)

2. Strip part of the sheath from the

Ethernet cable.

1. Drill a hole on the rubber seal

plug and insert an Ethernet cable

through the opening.

Rubber Seal

Plug

Assembling Steps

Recommended cable gauge: 24AWG (0.51 mm)

Connecting RJ45 Ethernet Cable

o: white/orange stripe

O: orange solid

g: white/green stripe

B: blue solid

b: white/blue stripe

G: green solid

br: white/brown stripe

BR: brown solid

3. You will need an RJ45 crimping tool to

attach the Ethernet wires to a connector.

When done, connect the cable to the

camera’s Ethernet RJ45 socket.

4. Press the Ethernet cable into the routing path at

the bottom of the camera so that the cable will not

get in the way when the metal mounting plate is

attached.

EN - 7

English

Wall mount

1. Attach the supplied alignment sticker to the wall.

2. Using the circle marks on the sticker, drill at least 2 pilot holes symmetrically on each side into the

wall. Then hammer the four supplied plastic anchors into the holes.

3. Through three or four holes on the mounting plate, insert the supplied screws into the corresponding

holes and secure the mounting plate with a screwdriver.

4. Feed the cables through the triangular cutout A or side opening B. If you want to use hole B, remove

the side cover using a screwdriver. Secure the camera base to the mounting plate with three supplied

screws.

5. Remove the black cover.

Black Cover

EN - 8

POWER C

OLLIS

ION

LINK

CEIVE

PARTITION

12345

Network Deployment

1. Connect RJ45 Ethernet cable to a switch.

Use a Category 5 Cross Cable when your

network camera is directly connected to PC.

2. Connect the AC cables from the terminal

block as an alternate power source. The IO

cables are user-supplied.

Ethernet

Non-PoE Switch

Pin 1

Pin 2

AC 24V±10%

Black

Red

General Connection (without PoE)

Ceiling mount

1. Attach the supplied alignment sticker to the ceiling.

2. Using the circle marks on the sticker, drill at least 2 pilot holes symmetrically on each side into the

ceiling. Then hammer the four supplied plastic anchors into the holes.

3. Through three or four holes on the mounting plate, insert the supplied screws into the corresponding

holes and secure the mounting plate with a screwdriver.

4. Feed the cables through the triangular cutout A or side opening B. If you want to use hole B, remove

the side cover using a screwdriver. Secure the camera base to the mounting plate with three supplied

screws.

5. Remove the black cover.

Black Cover

EN - 9

English

Power over Ethernet (PoE)

POWER COLLISION

LINK

RECEIVE

PARTITION

12345

PoE Switch

When using a PoE-enabled switch

The Network Camera is PoE-compliant, allowing transmission of power and data via a single Eth-

ernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch

via Ethernet cable.

POWER COLLISION

LINK

RECEIVE

PARTITION

12345

When using a non-PoE switch

Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE

switch.

PoE Power Injector

(optional)

Non-PoE Switch

Altri manuali per FD8335H

Indice

Altri manuali Vivotek Telecamera di sicurezza

Vivotek

Vivotek SUPREME MA9321-EHTV Manuale utente

Vivotek

Vivotek TS6346-EHL Manuale utente

Vivotek

Vivotek IB9365-EHT Manuale utente

Vivotek

Vivotek FD8136 Manuale utente

Vivotek

Vivotek IP7133 Manuale utente

Vivotek

Vivotek IP8337H-C Manuale utente

Vivotek

Vivotek FE8173 Manuale utente

Vivotek

Vivotek Supreme MD8563-DEH Manuale utente

Vivotek

Vivotek FD9187 Series Manuale utente

Vivotek

Vivotek PT3117 Manuale utente

Vivotek

Vivotek IP7138 Manuale utente

Vivotek

Vivotek Supreme IP8151 Manuale utente

Vivotek

Vivotek Supreme MD8563-EH Manuale utente

Vivotek

Vivotek PZ7111 Manuale utente

Vivotek

Vivotek PZ8111 Manuale utente

Vivotek

Vivotek FE8172V Manuale utente

Vivotek

Vivotek IP8371E Manuale utente

Vivotek

Vivotek FD8166A-N Manuale utente

Vivotek

Vivotek IP8161 Manuale utente

Vivotek

Vivotek Supreme MS8392-EV Manuale utente

Vivotek

Vivotek FD8163 Manuale utente

Vivotek

Vivotek PD8136 Manuale utente

Vivotek

Vivotek IB9387-LPR Manuale utente

Vivotek

Vivotek 2M Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente

Lumens

Lumens VC-A50PNW Manuale utente