VPI Industries PLAYER Manuale utente

VPI Player

Turntable Manual

Setup and Instruction Manual

VPI Industries, Inc., 77 Cliffwood Ave. #5D, Cliffwood, NJ 07721

http://www.vpiindustries.com

Player Turntable Packing List

Serial #:________________

Player Chassis

Cartridge Installed

Instruction Manual

Drive Belt

Power Supply

Platter

Tonearm

Date: __________

Final Check by: ____________________

PLAYER SPECIFICATIONS:

Type Belt drive (manual turntable)

Motor 24 VAC Synchronous AC Motor

Turntable Platter Machined MDF

Diameter 11.81" (30.0 cm)

Turntable Speeds 33-1/3 RPM and 45 RPM

Wow and Flutter 0.06% WOW (In accordance with DIN specification)

0.04% Flutter (In accordance with DIN specification)

Rumble <-80dB (IEC 98A Unweighted)

Effective Arm Length 240.7 mm

Overhang 0.65" (16.4 mm) Lofgren A

Offset Angle 21.8°

Arm Mass 10g (without cartridge)

Stylus Pressure Adjustment Range 0 - 3g (with 4 g cartridge)

Cartridge Ortofon 2M Red

Output 5.5 mV @ 1 KHz

Phono Preamplifier Gain 35 db

Cartridge Loading 150 pF Across 47K Ohms

Frequency Response 20 Hz –20 Khz (-0.5 db at 20 Hz)

Low Frequency Rolloff -1.4 db @ 10 Hz

Output Voltage (on RCA Jacks) 287 mV @ 1 KHz

Headphone Amplifier Gain 10 db

Frequency Response 20 Hz –20Khz (-0.4 db at 20 KHz)

Output Level 395 mW per Channel @ 150 Ohm

165 mW per Channel @ 32 Ohm

Power Supply 24 VAC @ 50 - 60Hz

Power Consumption 7.7W at full output with 32 Ohm headphones

Dimensions 18.5" (470 mm) W x 13.5" (343 mm) D x 4.3" (109 mm) H

Weight 12.9 lbs. (5.9 kg)

IMPORTANT: READ BEFORE PROCEEDING!

Read and follow the SAFETY INSTRUCTIONS below.

Save all packing materials. The Player should only be moved or shipped in its original packaging to

reduce the risk of damage in transit.

The Player must be placed on a flat, level surface. This will make setup easy, provide better sound

quality, and put less strain on the main bearing.

SAFETY INSTRUCTIONS:

Follow the instructions below to reduce risk of electrical hazard or

injury.

1. To avoid electrical shock, do not open the motor cover.

2. If the power cord provided with the Player does not reach an outlet, use a heavy-duty, grounded

extension cord.

3. To avoid electrical shock, always plug the Player into a grounded outlet.

4. Do not expose the Player to rain or excessive moisture.

INTRODUCTION:

The VPI Player is a high-end entry level turntable. The Player comes complete with a headphone

amplifier, phonostage, and pre-mounted Ortofon 2M Red cartridge on a 9 inch Gimbaled/Yoke bearing, it

is the perfect solution to enjoy your records! It also has standard RCA connections giving the ability to

hook up to a standard amplifier and desktop/floor standing speakers. The Player turntable is a precision

instrument. It has been thoroughly tested.

WARNING: The Player’s phonostage is defeat-able but must be disengaged before being plugged

into another phonostage. Doing so could result in serious damage to your speakers. See your

local dealer or check online for directions to disengage your internal phonostage.

OPENING THE BOX:

The VPI Player is protected by custom designed foam packaging to make it easy to remove and begin

your listening experience. All foam parts easily lift off from the box. Make sure to save all packaging in

the event you ever need to safely ship your Player table.

Setting up the Player

The Player must be placed on a flat, level surface. This will make setup easy, provide better sound

quality, and put less strain on the main bearing.

1. Place the turntable chassis on the shelf or stand where it will be used. The better isolation you

provide the Player, the better it will sound. We highly recommend a 1 to 3 inch thick maple shelf

sitting on rubber isolator feet for this purpose.

2. Remove the turntable platter and place the platter on the tapered spindle. The platter bearing is

lubricated; no additional lubrication is needed for at least one year. If you need to lubricate the

bearing place 3 drops of 40 weight motor oil in the spindle hole.

3. Connect the power cord to turntable.

4. Place the drive belt around the platter and around the pulley on the motor. The belt does not have to

be level on the platter. It will self-level when the platter starts rotating.

5. For 33 RPM operation, place the belt on the upper part of the pulley. For 45 RPM operation, place the

belt on the lower, wider part of the pulley. The center groove in each diameter is the correct speed.

To determine the precise speed, use a strobe disc. The VPI Synchronous Drive System speed

controller provides the ultimate speed accuracy and best sound. Check with your dealer about

availability.

REMOVING THE CARTRIDGE GUARD

The Ortofon 2M Red cartridges pre-mounted on the Player comes with a

cartridge guard to protect the stylus. To remove the guard (while facing the

Player) gently press the tab of the guard towards you to release and remove.

Arm Height and Azimuth

Both your arm height and azimuth is already factory set for you! All adjustments are optional. If you want

to make your own adjustments you can adjust the height of the arm from underneath your turntable under

the arm base, and the azimuth using the two small screws located on the right hand side of the arm tube.

Optional adjustment for arm height (VTA) as follows:

Loosen the nut under the tone arm-base, remove the ground wire, then you may adjust the height by

turning the brass nut.

Optional adjustment for the azimuth as follows:

You may adjust azimuth by loosening the side screws and turning the armtube.

CHANGING SPEEDS:

The VPI Player comes with a two speed pulley, 33 and 45. To adjust the speeds simply move the belt

from one pulley groove to another.

CONNECTING TO THE PREAMPLIFIER/AMPLIFIER

Only use interconnects that are shielded and properly grounded. Non-shielded can hum.

The ground connection is available to eliminate hum if necessary. If hum is present, first connect a

ground lead from the connector block to the preamplifier or amplifier to which the output cable is

connected. If this does not eliminate the hum, run a ground wire from the turntable chassis to the

connector block as well. The block's connector will accept bare wires, spade lugs, or ring tongue

connectors.

Do NOT plug the Player into an external phonostage

unless you have disengaged your internal phonostage!

Doing so could possibly damage your speakers!

PLAYING RECORDS

Make sure the VPI slip mat that comes standard with the Player is secure.

If using headphones, plug your headphones into the headphone amplifier located in the front left of

the Player. Be sure to set your volume at a preferred level before listening.

Press the power button and sit down and enjoy listening to your records with.

GENERAL USE

Allow at least 20 hours of break-in time.

The motor will make some low-level noise. This will not get into the system. The motor and bearings

will become quieter as you use your Player.

RECOMMENDED UPGRADES (SEE YOUR LOCAL DEALER)

HR-X Center Weight

Scout aluminum feet

HR-X mini feet

JMW 9 Unipivot Tonearm

Aluminum platter

Defeat-able Phonostage –You can upgrade as you grow with your system

Ortofon 2M Blue, Bronze, or Black (other cartridges can be used but the 2M series is compatible

and easy to use with the Player)

VPI Industries, Inc. Limited Warranty

VPI Industries, Inc. (VPI) warrants this unit against defects in materials and/or workmanship for one (1)

year from the date of purchase by the original retail purchaser. VPI’s sole obligation under this warranty is

limited to the repair or replacement, at VPI’s option, of any part(s) found to be defective. VPI’s obligation

to repair or replace defective parts is the purchaser’s sole and exclusive remedy, and VPI shall not be

liable for any direct or indirect injury and/or property damage arising out of the use of the product or

defect in or failure of the product.

This warranty does not extend to any unit whose serial number has been defaced or altered. Any product

that VPI determines causes a defect or malfunction due to incorrect installation, modification, misuse, or

servicing by the purchaser, or service technician not authorized by VPI to perform such service will not be

warranted. This warranty does not cover trivial or cosmetic defects that do not impair the unit’s normal

function.

VPI reserves the right to make changes in this product without assuming any obligation to install such

change in any product previously manufactured. This warranty to repair or replace defective parts is in

lieu of all other express or implied warranties of merchantability or fitness for a particular purpose. There

are not warranties that extend beyond the description herein.

Some states do not allow exclusion of implied warranties or limitation of incidental or consequential

damages, so the above exclusion or limitations may not apply to you. This warranty gives you specific

legal rights, and you may also have other rights that vary from state to state.

http://vpiindustries.com/warranty/

Indice

Altri manuali VPI Industries Giradischi

VPI Industries

VPI Industries VPI Classic 1 Manuale

VPI Industries

VPI Industries Signature DS Manuale utente

VPI Industries

VPI Industries Classic Manuale

VPI Industries

VPI Industries Classic Direct Manuale

VPI Industries

VPI Industries Classic 3 Manuale

VPI Industries

VPI Industries VPI JMW-3D Manuale

VPI Industries

VPI Industries Scoutmaster Manuale utente

VPI Industries

VPI Industries JMW 10 Manuale

VPI Industries

VPI Industries Scoutmaster Manuale

VPI Industries

VPI Industries TNT-5 Manuale

VPI Industries

VPI Industries JMW-9T Manuale utente

VPI Industries

VPI Industries HW-19 JR Manuale

VPI Industries

VPI Industries Nomad Manuale

VPI Industries

VPI Industries HW-19 MK-4 Manuale

VPI Industries

VPI Industries Signature 21 Manuale utente

VPI Industries

VPI Industries ARIES Guida utente

VPI Industries

VPI Industries JMW-9 Scout Tonearm Manuale utente

VPI Industries

VPI Industries Scout Jr. Manuale

VPI Industries

VPI Industries TNT HR-X Manuale

VPI Industries

VPI Industries ARIES 3 Guida utente

VPI Industries

VPI Industries Scout 2/JMW-9T Manuale

VPI Industries

VPI Industries TNT-4 AIR Manuale

VPI Industries

VPI Industries JMW-9 Manuale

Manuali Giradischi popolari di altre marche

Gemini

Gemini CDT-05 MKII Manuale utente

Rotel

Rotel RP-820 Manuale utente

Shuman

Shuman MC-250BT Manuale utente

Stanton

Stanton STR8-150 Manuale utente

Audio Technica

Audio Technica AT-LPW40WN Manuale utente

Crosley

Crosley McQueen CR7011-GY Manuale utente

Reloop

Reloop SMP-1 Manuale utente

auna

auna TT-Classic Plus Manuale utente

COMO AUDIO

COMO AUDIO Turntable Analog Manuale utente

Dual

Dual 1009 F Manuale utente

REED

REED Muse3C Manuale utente

AXIOMTEK

AXIOMTEK OPS883-H Series Manuale utente

Pioneer

Pioneer PL-71 Manuale utente

Vestax

Vestax PDX-a1 Manuale utente

Denon

Denon DP-400 Manuale utente

Dual

Dual 504 Manuale utente

Audio-Techica

Audio-Techica AT-LP60XBT Manuale utente

Goldring

Goldring G99 Manuale utente