Vulcan-Hart V SERIES Manuale utente

F-37418 (12-09) Rev 2

VULCAN-HART

DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC

WWW.VULCANHART.COM

3600 NORTH POINT BLVD.

BALTIMORE, MD 21222

TOPS

Open Top

Hot Top

Griddle Top

Work Surface

BASES

Standard Oven

Convection Oven

Cabinet Base

ONE POWERFUL PACKAGE

SERVICE MANUAL

V SERIES HDR

GAS RANGES

- NOTICE -

This manual is prepared for use by trained service technicians and

should not be used by those not properly qualified. If you have

attended a service school for this product, you may still be qualified to

perform the procedures described in this manual. This manual is not

intended to be all encompassing. If you have not attended a service

school for this product, you should read, in its entirety, the repair

procedure you wish to perform to determine if you have the necessary

tools, instruments and skills required to perform the procedure.

Procedures for which you do not have the necessary tools,

instruments and skills should be performed by a trained service

technician.

For additional information on Vulcan- Hart or to locate an authorized parts and service

provider in your area, visit our website at www.VulcanHart.com.

Page 2of 36

IMPORTANT FOR YOUR SAFETY

THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS

EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND

ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.

POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE

EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED

FROM THE LOCAL GAS SUPPLIER. IN THE EVENT OF A POWER FAILURE, DO NOT

ATTEMPT TO OPERATE THIS DEVICE.

IMPORTANT

IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN UNITS AT MAIN SHUTOFF

VALVE AND CONTACT THE LOCAL GAS COMPANY OR GAS SUPPLIER FOR SERVICE.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN

THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

WARNING: SHUT OFF THE GAS BEFORE SERVICING THE UNIT.

WARNING: PRIOR TO LIGHTING, CHECK ALL JOINTS IN THE GAS SUPPLY LINE

FOR LEAKS. USE SOAP AND WATER SOLUTION. DO NOT USE AN OPEN FLAME.

A. CHECK ALL JOINTS PRIOR TO THE GAS VALVE (SOLENOID)

BEFORE LIGHTING UNIT.

B. CHECK ALL JOINTS BEYOND GAS VALVE (SOLENOID)

AFTER UNIT IS LIT.

WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR

MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THE

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS THOROUGHLY

BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.

WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH

THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR

OTHER LOCAL ELECTRICAL CODES.

WARNING: APPLIANCES EQUIPPED WITH A FLEXIBLE ELECTRIC SUPPLY CORD

ARE PROVIDED WITH A THREE-PRONG GROUNDING PLUG. IT IS IMPERATIVE

THAT THIS PLUG BE CONNECTED INTO A PROPERLY GROUNDED THREE-PRONG

RECEPTACLE. DO NOT REMOVE THE GROUNDING PRONG FROM THIS PLUG.

IN THE EVENT OF A POWER FAILURE, DO NOT ATTEMPT TO OPERATE THIS DEVICE.

Page 3of 36

TABLE OF CONTENTS

GENERAL

Introduction

Installation

Operation

Cleaning

Lubrication

Tools

Specifications

REMOVAL AND REPLACEMENT OF PARTS

Electrical Lockout / Tagout Procedure

Gas Lockout / Tagout Procedure

Units Mounted On Casters

Covers and Panels

Manifold Cover

Kick Panel

Component Removal

Oven Control Panel(S Model)

Oven Control Panel (C Model)

Pilot Safety Valve and temperature Control Assembly (S Model)

Pilot Safety Valve (S Model)

Temperature Control (S Model)

Temperature Control (C Model)

Solenoid, Pilot Safety and Manual Gas Shut-Off Valve Assembly (C Model)

Solenoid (C Model)

Pilot Safety Valve (C Model)

Manual Gas Shut-Off Valve (C Model)

Oven Pilot Assembly

Oven Burner Assembly

Oven Burner Nozzle and Gas Orifice

Pilot Quick Disconnect Valve

Top Section Burner (Open Top)

Top Section Burner (Char Broiler)

Top Section Burner (French/Hot Top and Griddle)

Top Section Burner Valve

Fan Control Switch (C Model)

Convection Motor (C Model)

Oven Door Microswitch (C Model)

SERVICE PROCEDURES AND ADJUSTMENTS

Gas Leak Check

Gas Pressure Check

Gas Pressure Regulator Adjustment

Oven Pilot Flame Check and Adjustment

Oven Burner Nozzle and Gas Orifice Check

Air Shutter Adjustment

Page 4of 36

Top Burner Adjustment

Oven Burner Adjustment

Oven Door Microswitch Test

Fan Control Switch Test (C Model)

Convection Oven Motor Test (C Model)

Solenoid Test (C Model)

ELECTRICAL OPERATION

Component Function

Sequence of Operation

Wiring Diagrams

120V C Model

208V C Model

TROUBLESHOOTING

Troubleshooting Chart

CONDENSED SPARE PARTS LIST

Page 5of 36

GENERAL

INTRODUCTION

Procedures in this manual will apply to all models unless specified. Pictures and illustrations can

be of any model unless the picture or illustration needs to be model-specific.

Before performing maintenance on the equipment, thoroughly read this manual and carefully

follow the instructions in the order given.

Installation

Refer to the Installation and Operation manual for detailed installation instructions.

Operation

Refer to the Installation and Operation manual for specific operating instructions.

Cleaning

Refer to the Installation and Operation manual for cleaning instructions.

Lubrication

The convection motor has sealed bearings and requires no additional lubrication.

TOOLS

Standard

Standard set of hand tools.

VOM with A.C. current tester (Any quality VOM with sensitivity of at least 20,000 ohms

per volt can be used).

Special

Hazardous gas leak tester.

Manometer.

SPECIFICATIONS

Electrical

Voltage - 120/60/1 or 208/60/1 (optional)

Amps -15 Amps

Frequency - 50/60 Hz

Page 6of 36

Gas Line Pressures

Operating Pressures

Natural - Recommended (in. W.C.) 6.0

Propane - Recommended (in. W.C.) 10.0

Incoming Pressure

Natural - Recommended (in. W.C.) 7.0 min.

Propane - Recommended (in. W.C.) 11.0 min

REMOVAL AND REPLACEMENT OF PARTS

ELECTRICAL LOCKOUT/TAGOUT

Electrical Lockout/Tagout procedures are used to protect personnel working on an electrical

appliance. Perform the following steps when performing any type of maintenance or service on

an electrically operated appliance.

WARNING: Always perform the Lockout/Tagout procedure before removing any sheet

metal panels or attempting to service this equipment. Failure to comply with this

procedure can cause property damage, injury or death.

1. In electrical box, place the unit's circuit breaker to the OFF position.

2. Place a lock or other device on the electrical box cover to prevent someone from placing

the circuit breaker ON.

3. Place a tag on the electrical box cover to indicate that the unit has been disconnected for

service and that power should not be restored until the tag is removed by maintenance

personnel.

4. Disconnect the unit power cord from electrical outlet.

5. Place a tag on the power cord to indicate that oven has been disconnected for service

and power should not be restored until the tag is removed by maintenance personnel.

Page 7of 36

GAS LOCKOUT/TAGOUT

The Gas Lockout/Tagout procedure is used to protect personnel working on a gas appliance.

Before performing any maintenance or service that requires gas disconnections, follow these

steps:

WARNING: All gas joints disturbed during servicing must be checked for leaks. Do not

use an open flame. Use a hazardous gas tester or a soap and water solution (Bubbles

indicate a gas leak). Failure to comply can cause property damage, injury or death.

WARNING: Do not operate a gas-fueled appliance if a gas leak is present.

1. Locate the gas valve or inlet.

2. Place the valve in the OFF position.

3. Place a tag on the valve indicating that service is being performed on the equipment and

that the gas must remain off until service is complete.

4. Place a locking device on the gas valve or inlet, preventing connection until the lock is

removed.

5. On the appliance, make sure all flame sources are extinguished and/or removed.

6. Bleed residual gas from the unit inlet line and allow time for the gas to dissipate before

beginning service on the appliance.

UNITS MOUNTED ON CASTERS

WARNING: Units mounted on casters must use a flexible connector (not supplied by

manufacturer) that complies with the Standard for Connectors for Movable Gas

Appliances, ANSI Z21.69, CSA 6.16 and a quick-disconnect device that complies with the

Standard for Quick-Disconnect Devices for Use with Gas Fuel, ANSI-Z21.41, CSA 6.9.

WARNING: If disconnection of the restraint is necessary, turn off the gas supply before

disconnection. Reconnect restraint prior to turning the gas supply on and returning the

unit to its operating location.

NOTE: The unit must be releveled front to back and side to side if it is moved for any reason.

COVERS AND PANELS

Manifold Cover (All Models)

WARNING: Always perform the Electrical Lockout/Tagout procedure before removing

any sheet metal panels or attempting to service this equipment. Failure to comply with

this procedure can cause property damage, injury or death.

Page 8of 36

WARNING: Perform the GAS LOCKOUT/TAGOUT procedure before servicing the unit.

1. Perform the ELECTRICAL LOCKOUT/TAGOUT Procedure.

2. Rotate the yellow gas shut-off knob to the OFF position.

Figure 1: Gas Shut-Off Valve Knob

3. Loosen the setscrew in the burner control knobs and remove the knobs.

4. Remove the two (2) drive screws securing the manifold cover in place and remove the

manifold cover.

5. Reverse the procedure to install the manifold cover.

Figure 2: Manifold Cover Removal

Kick Panel (All Models)

WARNING: Always perform the Electrical Lockout/Tagout procedure before removing

any sheet metal panels or attempting to service this equipment. Failure to comply with

this procedure can cause property damage, injury or death.

WARNING: Perform the GAS LOCKOUT/TAGOUT procedure before servicing the unit.

1. Perform the ELECTRICAL LOCKOUT/TAGOUT procedure.

2. Open the kick panel.

3. Remove the two (2) screws securing the left hinge and remove the hinge.

4. Slide the kick panel to the left to disengage it from the hinge.

5. Reverse the procedure to install the kick panel.

Figure 3: Kick Panel Removal

Page 9of 36

COMPONENT REMOVAL

Oven Control Panel (S Model)

WARNING: Always perform the Electrical Lockout/Tagout procedure before removing

any sheet metal panels or attempting to service this equipment. Failure to comply with

this procedure can cause property damage, injury or death.

WARNING: Perform the GAS LOCKOUT/TAGOUT procedure before servicing the unit.

1. Perform the ELECTRICAL LOCKOUT/TAGOUT procedure.

2. Perform the GAS LOCKOUT/TAGOUT procedure.

3. Rotate the yellow gas shut-off knob to the OFF position.

Figure 4: Gas Shut-Off Valve Knob

4. Open the kick panel to gain access to the screw securing the control panel.

5. Loosen the setscrew from the yellow gas shut-off knob and remove the knob.

6. Loosen the setscrew from the temperature control knob and remove the knob.

7. Remove the oven knob ring.

8. Remove the screw securing the control panel.

9. Remove the control panel by lifting the bottom up and removing it from the tab located at

the top of the control panel.

10. Reverse the procedure to install the oven control panel.

11. Test the oven to verify proper operation.

Figure 5: S Model Control Panel Removal

Oven Control Panel (C Model)

WARNING: Always perform the Electrical Lockout/Tagout procedure before removing

any sheet metal panels or attempting to service this equipment. Failure to comply with

this procedure can cause property damage, injury or death.

WARNING: Perform the GAS LOCKOUT/TAGOUT procedure before servicing the unit.

1. Perform the ELECTRICAL LOCKOUT/TAGOUT procedure.

2. Perform the GAS LOCKOUT/TAGOUT procedure.

Page 10 of 36

3. Rotate the yellow gas shut-off knob to the OFF position.

Figure 6: Gas Shut-Off Valve Knob

4. Open the kick panel to gain access to the screw securing the control panel.

5. Loosen the setscrew from the yellow gas shut-off knob and remove the knob.

6. Loosen the setscrew from the temperature control knob and remove the knob.

7. Remove the oven knob ring.

8. Remove the two (2) screws from the temperature control mount bracket located in the

front of the control panel.

9. Remove the screw securing the control panel.

10. Raise the lower end of the control panel to gain access to the fan control switch tabs.

11. Remove the fan control switch by compressing the tabs and pulling the switch out of the

front of the control panel.

12. Tag and disconnect the fan control switch electrical connectors.

13. Remove the control panel by lifting the bottom up and removing it from the tab located at

the top of the control panel.

14. Reverse the procedure to install the oven control panel.

15. Test the oven to verify proper operation.

Figure 7: C Model Control Panel Removal

Pilot Safety Valve and Temperature Control Assembly (S Model)

WARNING: Always perform the Electrical Lockout/Tagout procedure before removing

any sheet metal panels or attempting to service this equipment. Failure to comply with

this procedure can cause property damage, injury or death.

WARNING: Perform the GAS LOCKOUT/TAGOUT procedure before servicing the unit.

1. Perform the OVEN CONTROL PANEL removal procedure for the standard oven.

2. Disconnect the flex line(s) from the pilot safety valve

3. Disconnect the 3/8" union from the bottom of the pilot safety valve.

4. Disconnect the flex line from the top of the temperature control.

Altri manuali per V SERIES

Indice

Altri manuali Vulcan-Hart Allineare

Vulcan-Hart

Vulcan-Hart VG36 Manuale utente

Vulcan-Hart

Vulcan-Hart RG-6 Manuale utente

Vulcan-Hart

Vulcan-Hart G260 Manuale

Vulcan-Hart

Vulcan-Hart MG12 ML-52549 Manuale utente

Vulcan-Hart

Vulcan-Hart Value Series V36-1 Manuale utente

Vulcan-Hart

Vulcan-Hart E12FP Manuale utente

Vulcan-Hart

Vulcan-Hart GH Manuale utente

Vulcan-Hart

Vulcan-Hart VG24 Manuale utente

Vulcan-Hart

Vulcan-Hart MG12 Manuale utente

Vulcan-Hart

Vulcan-Hart G481L Manuale utente

Vulcan-Hart

Vulcan-Hart E36LC SERIES Manuale utente

Vulcan-Hart

Vulcan-Hart 36L Manuale utente

Vulcan-Hart

Vulcan-Hart VG260 Manuale utente

Vulcan-Hart

Vulcan-Hart 148L Manuale utente

Vulcan-Hart

Vulcan-Hart GH30 Manuale utente

Vulcan-Hart

Vulcan-Hart V-24S SERIES Manuale utente

Vulcan-Hart

Vulcan-Hart VGM36 Manuale utente

Vulcan-Hart

Vulcan-Hart GH45 Manuale utente

Vulcan-Hart

Vulcan-Hart GH30 Manuale utente

Vulcan-Hart

Vulcan-Hart G60CB-10T Manuale utente

Vulcan-Hart

Vulcan-Hart E12FP Manuale utente

Vulcan-Hart

Vulcan-Hart GH60 Manuale utente

Vulcan-Hart

Vulcan-Hart V6B36S Manuale utente

Vulcan-Hart

Vulcan-Hart G60CB-4FT36 Manuale utente

Manuali Allineare popolari di altre marche

Samsung

Samsung FCQ321HTUW Manuale utente

Kenmore

Kenmore 790.45712 Manuale utente

Wolf

Wolf CHR CHSSR Manuale utente

Smeg

Smeg Built-in Microwave Oven Manuale di istruzioni

Zanussi

Zanussi ZCG054G Manuale utente

Whirlpool

Whirlpool 8575985-W Manuale elenco delle parti

Frigidaire

Frigidaire 316000635 Manuale utente

GE JCSS630 Manuale utente

Samsung

Samsung NX58M9960P series Manuale utente

Hotpoint

Hotpoint RB524R Guida all'installazione

Whirlpool

Whirlpool Roper FGP305KW3 Manuale utente

Amana

Amana ART6610 SERIES Manuale utente

Maytag

Maytag MERH770WB Manuale utente

Fulgor Milano

Fulgor Milano SOFIA Manuale utente

Premier

Premier EF-4358GH Manuale utente

Kenmore

Kenmore 790.9010 Series Manuale utente

KitchenAid

KitchenAid KESC300 Manuale utente

Frigidaire

Frigidaire FFEF3012LS Guida utente