Warmup StickyMat 3D Manuale utente

StickyMat 3D™

Installation Manual

Electric

Heating System

Technical Helpline

0345 345 2288

Experience MyHeating™

Download now for iOS and Android

Easy to use

Simple and secure

set up with 24/7

support

Unique to Warmup:

Natural Language Programming™

Programming that speaks your language

Please scan the QR code

for more information

The world’s best-selling floor heating brand™

Over 2 million installations in

more than 60 countries

EasySwitch™

Always on the best

tari, automatically

SmartGeo™

Smarter geo-fencing.

Reduce energy usage

by up to 25%

Contents

Quick Install Guides��4

Components Required for Installation�� 8

Do’s & Don’ts �� 9

Step 1 - Electrical Supply �� 10

Step 2 - Substrate Considerations �� 12

Step 3 - Layout Planning�� 14

Wall Applications

Step 4 - Install StickyMat 3D™�� 16

Step 5 - Select Wall Covering�� 19

Step 6 - Apply the Wall Covering�� 20

Floor Applications

Step 4 - Install StickyMat 3D �� 22

Step 5 - Select Floor Covering�� 25

Step 6 - Lay the Floor Covering�� 26

Step 7 - Connect the Thermostat�� 28

Troubleshooting�� 29

Performance Troubleshooting �� 31

How to test the heater & floor sensor�� 33

Layout Plan �� 34

Control Card�� 35

Warranty�� 36

Technical Specifications �� 38

WARNING

Your Warmup heating system has been designed so that installation

is quick and straight forward, but as with all electrical systems,

certain procedures must be strictly followed. Please ensure that you

have the correct heater(s) for the area you wish to heat. Warmup plc,

the manufacturer of the Warmup StickyMat 3D System, accepts no

liability, expressed or implied, for any loss or consequential damage

suered as a result of installations which in any way contravene the

instructions that follow.

It is important that before, during and aer installation that all

requirements are met and understood. If the instructions are

followed, you should have no problems. If you require help at any

stage, please contact our helpline.

You may also find a copy of this manual, wiring instructions and other

helpful information on our website:

www.warmup.co.uk

Wall Heating - Quick Install Guide

Quick Install Guide - The full installation instructions in this

manual must be followed�

•We recommend installing

Warmup insulation boards for

optimum performance.

•Test the resistance of the

heater ensuring it is within the

range set out in the Reference

Resistance Band tables.

•Cut, turn and aix the mat

to the substrate using self-

adhesive mesh or double

sided tape.

•Make electrical provision for

the heater (30 mA RCD, 35 mm

deep electrical back boxes,

trunking).

•Mark on the boards where any

penetrating fixtures are likely

to be such as, mirrors, shower

screens, towel rails etc.

•The cable should be installed

40 mm in from the edge of the

heated area or penetrations

through the substrate.

Wall Heating - Quick Install Guide

•Test the resistance of the

heater aer installation and

check against the previous

value to ensure no damage

has occurred.

•Test the resistance of the

heating cable aer tiling and

check against previous values

to ensure no damage has

occurred.

•Connect your Warmup

thermostat.

DO NOT install the thermostat

on the same wall as the

heater.

•Channel a groove in the

boards for the coldtail &

termination joints, enabling

them to fit flush with the top

of the heater. DO NOT tape

over these joints!

•Install the sensor probe

centrally between two runs of

the heater.

•Lay the adhesive and tiles over

the system. Use flexible grout

when grouting.

•If a plaster finish is required,

apply a minimum cover of

10 mm.

• The heater, including its joints,

must be wholly within the

adhesive/plaster and not

exposed.

Floor Heating - Quick Install Guide

Quick Install Guide - The full installation instructions in this

manual must be followed�

•Ensure the subfloor is smooth,

dry and free from dust.

•Mark on the subfloor where

fixed objects, kitchen units etc.

are likely to be.

•The cable should be installed

40 mm in from the edge of the

heated area or penetrations

through the floor.

•Make electrical provision for

the heater (30 mA RCD, 35mm

deep electrical back boxes,

trunking).

•We recommend installing

Warmup insulation boards for

optimum performance.

•Test the resistance of the

heater ensuring it is within the

range set out in the Reference

Resistance Band.

Floor Heating - Quick Install Guide

•Channel a groove in the

subfloor for the coldtail &

termination joints, enabling

them to fit flush with the top of

the heater. DO NOT tape over

these joints!

•Install the floor sensor

centrally between two runs of

the heater.

•Lay tiles or levelling compound

over the system.

•The heater, including its

joints, must be wholly within

the adhesive or levelling

compound and not exposed.

•Use flexible grout when

grouting.

•Connect your Warmup

thermostat.

•Cut, turn and aix the mat

to the subfloor using self-

adhesive mesh or double

sided tape

•Any loose heating cable

removed from the mesh must

be installed at no less than

50 mm intervals and tab taped

in place.

•Test the resistance of the

heating cable aer installation

and check against the

previous value to ensure no

damage has occurred.

•Test the resistance of the

heating cable aer tiling and

check against previous values

to ensure no damage has

occurred.

Components Required

for Installation

Components available from Warmup

Warmup Insulation BoardsWarmup StickMat 3D™ System

Warmup Thermostat & Sensor

Probe

Additional components needed as part of your Warmup heating

installation:

30 mA Residual Current Device (RCD), required as part of all

installations.

Digital Multi-meter required for testing the resistance of the

heater and sensor probe.

Electrical tape to secure the sensor probe.

Electrical housing, back boxes and junction boxes.

Electrical trunking/conduit for housing the power leads.

Flexible tile adhesive and flexible grout.

Staple gun.

Do’s & Don’ts

Ensure that the control card at the back of the manual is

completed and fixed at the consumer unit along with any

plans and electrical test records as per the current edition of

BS7671�

Ensure the termination and coldtail joints are within a full bed

of adhesive/plaster directly beneath the heated floor or wall

finish�

Ensure the heat output of the floor or wall meets your

requirements�

Install the sensor probe centrally between two parallel runs of

heating cable and away from other heat sources such as hot

water pipes, lighting fixtures etc�

Use adhesives and grouts suitable for use with heating�

Ensure all furniture installed over underfloor heating has feet,

creating a minimum 50 mm ventilated space beneath it to

allow heat flow into the room�

Ensure that during the course of the installation no damage is

caused to the heater by falling or sharp objects�

Cut or shorten the heating element at any time�

Leave surplus heater rolled up under units or fixtures, use the

correct size heater�

Connect two heaters in series, only connect heaters in

parallel�

Attempt a DIY repair if you damage the heater, contact

Warmup for assistance�

Tape over manufactured joints or the sensor probe tip�

Install items above the heating system which have a

combined resistance of more than 1�5 tog in floor applications

or 1 tog in wall applications, as this may cause overheating�

Bend the heating cable under 25mm radius�

Install the thermostat on the same wall as the heating mat in

wall heating applications�

Install penetrating fixtures into the heated wall such as

shower screens, towel rails, mirrors etc�

DON’T

Step 1 -

Electrical Supply

Install the RCD

Install a dedicated 30 mA RCD or use an existing RCD. No more than

7.5 kW of heating should be connected to each 30 milliamp RCD. For

larger loads, use multiple RCD’s.

NOTE: It is possible to run the heater(s) from an existing circuit

protected by a 30 mA RCD. It should be calculated whether or not the

circuit can handle the additional load.

NOTE: A junction box is required if more than two heaters are being

connected to a single Warmup thermostat.

NOTE: When conducting an insulation resistance test on the supply

to the thermostat the thermostat and heaters must be isolated or

disconnected.

Warmup

Thermostat

13 amp fused

spur or RCD spur

supplying power to

the thermostat

Floor Sensor 300 mm into

heated area. Floor sensor

connected to thermostat

Coldtail & Termination

Joint recessed into

the subfloor. Coldtail

connected to the

thermostat

Indice

Altri manuali Warmup Sistema di riscaldamento

Warmup

Warmup DWS300 Manuale utente

Warmup

Warmup WHP1 Manuale utente

Manuali Sistema di riscaldamento popolari di altre marche

aerauliqa

aerauliqa QR350ABP Manuale utente

WatchGas

WatchGas ATEX BEACON Manuale utente

Viessmann

Viessmann Vitoligno 300-H Istruzioni operative

Lampoassa

Lampoassa 203GT Manuale utente

MSA

MSA SOA-1022 Manuale utente

nilan

nilan Compact P Manuale utente

ITR

ITR OASIS NE-S Manuale utente

Carrier

Carrier 48LJD Dimensioni e guida di installazione

aldes

aldes EVEREST XV Manuale utente

Kober

Kober C22SPV23MEF Manuale utente

Oxygen

Oxygen X-Air V400 Manuale utente

Carrier

Carrier FB4CNF Manuale utente

Kroll

Kroll HM200 Manuale

Kroll

Kroll HM200 Manuale

NuAire

NuAire XBOXER XBC Series Manuale utente

Trane

Trane VR104GD-U Series Manuale utente

Vents

Vents VUT V mini Manuale utente

Viessmann

Viessmann Divicon Manuale utente