Warmup + Kit Manuale utente

Indice

Altri manuali Warmup Termostato

Manuali Termostato popolari di altre marche

EWELLY

EWELLY EW-181 Manuale utente

Prolon

Prolon T1100 Istruzioni per l'installazione

Computherm

Computherm Q20 Manuale utente

Heatmiser

Heatmiser neoStat Manuale utente

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuale utente

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuale utente

Saswell

Saswell SAS920XWHB-7-S-RF Guida

Aircalo

Aircalo TFP1-ET85P2 Manuale utente

Honeywell

Honeywell CM721 Manuale utente

Carrier

Carrier DEBONAIR 33CS Manuale utente

Lennox

Lennox iHarmony Zone Thermostat Istruzioni per il montaggio

Gemtech

Gemtech GT7000 Manuale di istruzioni

Rollei

Rollei Smartes 45000 Manuale utente

Sinope

Sinope TH1300RF Manuale utente

Honeywell

Honeywell RLV4305 Manuale utente

Honeywell

Honeywell Prestige 2.0 THX9421 Manuale utente

NuTone

NuTone NTBZ48 Istruzioni operative originali

Stelpro

Stelpro MAESTRO ASMT402AD Manuale utente

Kit

Installation Guide

+

Contents

2

Components ....................................................

Step 1 - Download the MyHeating App .....................

Step 2 - Install the Boiler Receiver ........................

Step 3 - Mounting..............................................

Step 4 - Pairing the 4iE to the Boiler Receiver............

Step 5 - LED Indications ......................................

Step 6 - Control in event of communication error .......

Step 7 - Address setting ......................................

Troubleshooting ...............................................

Technical Specications.......................................

3

5

7

12

15

17

18

19

22

23

Kit for use with the 4iE

Components

Power Base Stand Boiler Receiver

Power Adapter with 1m

USB Cable

3

+

Kit

Step 1 - Download the MyHeating App

+

The MyHeating app is available for iOS and Android devices via the App Store or Google Play. If

you have not done so already, download the MyHeating app to your tablet or smartphone.

Registration

After the app has been successfully downloaded you will need to set up your MyWarmup

account. The 4iE Device can be registered via the app or by visiting my.warmup.com

Kit for use with the 4iE

Step 1 - Download the MyHeating App

5

+

Kit

Step 2 - Install the Boiler Receiver

+

Kit for use with the 4iE

Step 2 - Install the Boiler Receiver (Electrician Required)

Before making any permanent xtures Warmup recommends progressing through to ‘Step 4 -

Pairing the 4iE & Boiler Receiver’upon identifying preferred locations for the Boiler Receiver

and Power Base. This will ensure the wireless connection is not subject to range or interference

issues once installed.

IMPORTANT INFORMATION: Installation of the Boiler Receiver should only be carried out by a

qualied electrician. It requires a permanent 230V supply.

The Boiler Receiver should be connected to the central heating fused spur or circuit breaker in

accordance with current wiring regulations such that there is a single point of isolation for all

interconnected devices.

Ensure that multi stranded wires are fully inserted into the terminals and secured tightly. Any

loose strands should be trimmed as they could cause a short-circuit.

This product uses mains voltage electricity and work should only

be carried out by a qualied electrician. Electrical installation

to be in accordance with latest edition of BS7671 Wiring

Regulations and appropriate Statutory Regulations.

!

7

+

Kit for use with the 4iE

Step 2 - Install the Boiler Receiver (Electrician Required)

The Boiler Receiver should be installed in the boilers vicinity. Large metal objects such as the

boiler, hot water cylinder or radiators, should be at least 300mm away from the Boiler Receiver

and not directly between it and the 4iE.

Loosen both screws at

the bottom of the Boiler

Receiver and remove

the backplate.

Fix the backplate to the

wall using xing screws

provided.

Make sure to avoid cables or pipes

which may be buried in the wall

!

8

+

1 2

Kit for use with the 4iE

Step 2 - Install the Boiler Receiver (Electrician Required)

Wiring Diagrams

9

+

1 2 3 4

3

Kit for use with the 4iE

Step 2 - Install the Boiler Receiver (Electrician Required)

After the Boiler Receiver has been wired correctly reattach the front panel to the back plate

and tighten both screws to secure.

Restore power to the

boiler. The LED on the

Boiler Receiver will ash

RED which means it has

to be paired to the Power

Base.

4

10

+

4