Wave Central AXTX3 Manuale utente
AXIS AXTX3 TRANSMITTER
with AXIS PAINT
Menu Guide
June 6, 2019
Wave Central LLC
99 Garden Parkway, Suite C., Carlisle, PA 17013
+1 888 736 9283 www.wavecentralrf.com
1Wave Central LLC AXTX3 with PAINT June 2019
FORWARD
This document provides detail for the menus used for the AXTX3
transmitter with AXIS Paint. It is recommended that the user reads the
Operations manual for the AXIS TX PICO PLUS TRANSMITTER and AXIS
PAINT. These are available at www.wavecentralrf.com in the product
manual section. Wave Central LLC acknowledges Domo Tactical
Communications (DTC) and Videosys Broadcast for their contributions to
these products.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. WAVE CENTRAL,
LLC IS NOT LIABLE FOR DAMAGES TO THIS OR ASSOCIATED EQUIPMENT CAUSED
BY ANY ERRORS OR OMMISSIONS CONTAINED HEREIN. FIMILIARIZATION OF THESE
MENUS IS ENCOURAGED. HOWEVER, ANY CHANGES THAT MAY AFFECT THE
OPERATION PARAMETER’S PRE-PROGRAMED BY WAVE CENTRAL PRIOR TO
SHIPMENT.THE PROGRAMMING GUIDE IS USE AT USERS OWN RISK.
2Wave Central LLC AXTX3 with PAINT June 2019
CAUTION
The HD/SDI Video input connector is 75 Ohms.
Ensure that the video cable(s) are fitted with
75 Ohm and NOT 50 Ohm connectors.
The illustration on the right is the correct
BNC connector.
Failure to do so will damage the BNC
connector(s). The customer is liable for any
damages for not adhering to this practice.
3Wave Central LLC AXTX3 with PAINT June 2019
TRANSMITTER MENU GUIDE
The AXTX3 transmitter has been turned
ON
and will enter the initialization cycle (boot
up).
CANCEL/BACK DISPLAY SCREEN SCROLL/ENTER
CONFIRM
There are two push buttons located adjacent to the OLED display screen. The function
of the button on the left is Cancel/Back.To select a menu header, press in on the
joystick button on the right. Using the joystick controller, scroll up or down through the
menu headings: STATUS / CONFIG RF / CONFIG VIDEO / CONFIG AUDIO / CONFIG
DATA / PRESET / PATTERN GENERATOR / UNIT. Select by pressing the right joystick
button in then scroll up or down to the sub-menu, press the button in again to backlight
a selection, and then scroll to the desired setting. Press the right button in again to
ENTER/CONFIRM setting.
Pressing the Cancel/Back button will restore the previous
setting prior to pressing ENTER/CONFIRM.
DEFAULT MENU
INITIALIZATING….
5850.000 PRESET: 11
RF: ON TEMP: 44
RLoD 1920X1080i 29fps
WAVE CENTRAL
4Wave Central LLC AXTX3 with PAINT June 2019
Select the “Status” menu. Press the right joystick button in to Enter/Confirm. Use the
right joystick button to scroll down and view the following parameters.
Press the left button (CANCEL/BACK) to return to the STATUS menu. Scroll down to the
next menu using the right joystick button.
STATUS
BAND: 8MHz
CONST: 16-QAM
FEC: 1/2
GUARD 1/32
Video Input: SDI
ASI Input: OFF
RLoD 1920X1080i 29fps
Source: EMBEDDED 1
Mode: STEREO
Encoder: MPEG-1 LAYER2
Bitrate: 192kbps
5Wave Central LLC AXTX3 with PAINT June 2019
CONFIGURATIONMENUS
There are four menus: RF / VIDEO / AUDIO / DATA. Press the right joystick button in and
then scrolling up or down, select which menu you want to view. By pressing the right
joystick button in again will enter the menu.
RF ON/OFF
RF POWER (HIGH-MED-LOW)
To change RF POWER, press the right joystick button in to highlight, and then scroll up
or down to select the power level. Then press the right joystick button in again to
ENTER/CONFIRM. Scroll down to the next menu.
CONFIG RF
RF POWER
HIGH
RF ON/OFF
ON
6Wave Central LLC AXTX3 with PAINT June 2019
RF FREQUENCY
BACKLIT FREQUENCY DISPLAY
CHANGE FREQUENCY BY USING THE LEFT, RIGHT, UP AND DOWN JOY STICK, SCROLL AND
THEN PRESS IN TO CONFIRM/ENTER EACH INTEGER CHANGED.
NEW FREQUENCY SET
RF FREQUENCY
5850.000
RF FREQUENCY
5850.000
RF FREQUENCY
5880.000
RF FREQUENCY
5880.000
7Wave Central LLC AXTX3 with PAINT June 2019
RF BANDWIDTH (6, 7 & 8 MHz)
RF CONSTELLATION (QPSK, 16-QAM OR 64-QAM)
RF FEC (1/2, 2/3, 3/4, 5/6 AND 7/8)
RF GUARD INT (1/32, 1/16, 1/8 AND 1/4)
RF CONSTELLATION
16-QAM
RF GUARD INT
1/32
RF FEC
2/3
RF BANDWIDTH
8MHz
8Wave Central LLC AXTX3 with PAINT June 2019
CONFIG VIDEO
CONFIG VIDEO (OFF, Composite 1, Composite 2, S-Video, SDI and HDMI)
VIDEO SOURCE
VIDEO FORMAT
The AUTO FORMAT mode will sense the input video source and format to that input.
(AUTO, PAL, NTSC, NTSC NP, 720p 50, 720p 59.94, 720p 60, 1080i 50,
1080i 59.95
, 1080i 60,
1080p 23.97, 1080p 24, 1080p 24, 1080p 29.97, 1080p30, 1080psf 23.976, 1080psf 24, 1080pfs
25, 1080psf 29.97, 1080psf 30, 1080p 50, 1080p 59, 1080p 60, 1080dl 50, 1080dl 59 and 1080dl
60.
VIDEO SOURCE
SDI
CONFIG VIDEO
VIDEO FORMAT
AUTO
9Wave Central LLC AXTX3 with PAINT June 2019
VIDEO FORMAT MANUALLY SELECTED
Scroll down to the VIDEO MODE; press in the right joystick button to highlight modes.
Scroll up or down to the mode that you want to operate then press in the joystick button
to ENTER/CONFIRM.
VIDEO MODE (STANDARD DELAY, LOW DELAY and ULTRA LOW DELAY)
Scroll down to the ASI ON/OFF Menu
ASI ON/OFF (ON & OFF)
Pressing the button on the left of the LED display will take you to the top menu level.
Scroll down using the right joystick button. The next menu heading is CONFIG AUDIO.
VIDEO MODE
ULTRA LOW DELAY
ASI ON/OFF
OFF
VIDEO FORMAT
1080i 59.95
10 Wave Central LLC AXTX3 with PAINT June 2019
Indice
Altri manuali Wave Central Trasmettitore
