Wavecom WCM-TT040-50BB Manuale utente

Wavecom

User Manual

+ Certiﬁcate of Warranty and Product Support Information

WCM-TT040-50BB

Bluetooth Ready Battery Powered Printer

WCM-TT-040-40BB User Manual Wavecom

Printer Diagram 3

Charging the Printer 4

Operating the Printer 5

Loading Print Media 6

Loading Print Ribbon 7

Printer Functions 8

LED & Button Functions 8

Power on Utilities 8

Gap/Black Mark Sensor Calibration 9

Gap/Black Mark Calibration, Self-test and Dump Mode 9

Dump mode 10

Printer Initialization 10

Set Black Mark Sensor as Media Sensor and Calibrate the Black Mark Sensor 11

Set Gap Sensor as Media Sensor and Calibrate the Gap Sensor 11

Troubleshooting 12

Maintenance 14

Wavecom Tags 15

WCM-TT-040-40BB User Manual Wavecom

2422 23

Wavecom Thermal Transfer Printer

The TT040-50-BB printer is powered by a Lithium Ion Battery and features Bluetooth connectivity.

Important: Do not turn o the rear power switch on the TT040-50-BB. Always use the Power Button on the

side of the printer (7).

1. LED Indicator

2. Media view window

3. Feed Button

4. Label Exit Chute

5. Top Cover

Release Lever

6. Battery Indicator

7. Power Button

8. Power Socket

9. Isolation Switch

10. Power Switch

(Leave On)

11. Battery-Printer Power

Cable

(Do not remove)

12. USB-B Port

13. Bluetooth Module

14. Ribbon Rewind Hub

15. Print Head

16. Ribbon Rewind Gear

17. Ribbon Supply Hub

18. Gap Sensor

(Receiver)

19. Gap Sensor

(Transmitter)

20. Platen Roller

21. Black Mark Sensor

22. Media Guide

23. Media Guide Adjuster

Knob

24. Media Holders

25. Top Cover Hinge

26. Top Cover

27. Ribbon Access Cover

21 25 26 27

6 7 8 9 10 11 12 13

WCM-TT-040-40BB User Manual Wavecom

Charging the Printer

Using this method to charge the printer will avoid any issues with inrush current when the charging cable is

plugged in, which can occur if the battery is not isolated. Ensure the isolation switch is turned on once the

charging cable is plugged in, otherwise the battery will not charge.

The TT040-50-BB battery will take approximately eight hours to fully charge. Do not leave unattended while

charging.

1. Turn off the battery isolation switch on the side of

the printer.

3. Plug the charging cable into the power point.

5. Turn on the isolation switch on the side of the

printer.

2. Turn off the switch at the power point.

4. Plug the charging cable into the printer.

6. Turn on the switch at the power point.

WCM-TT-040-40BB User Manual Wavecom

Operating the Printer

Turning on the Printer

1. Before turning on the printer, ensure the battery is charged, and the battery isolation switch on the side of the

printer is switched ON.

2. Press and hold the power button on the side of the printer for three to ﬁve seconds. The Battery Status indicator

(next to the power button) will light up when the printer has turned on.

Connecting the Printer via the WinPATS App

Once the printer is on, you can connect your printer to your tablet via the WinPATS app.

1. First, ensure the Bluetooth module on the rear of the printer is displaying a green light, indicating that the module is

powered. If the module isn’t powered, ensure it has not unplugged by gently pressing it into the rear of the printer.

2. Open the WinPATS App, and tap the PRINT icon at the top of the screen.

3. You will be prompted to connect to a printer via Bluetooth - select your printer from the popup menu.

4. The printer should connect - you can verify this connection by checking the Bluetooth module on the rear of the

printer, which should display a Blue light. There should also be a Blue line under the Print icon in the WinPATS app, at

the top of the screen.

5. Once you have connected your printer, you will be able to print tags directly from your tablet, either from the

Inventory or during your test procedures.

WCM-TT-040-40BB User Manual Wavecom

Loading the media

Loading media into the TT-040-50 Printer is quick and easy. To begin, open the printer top cover by pulling the tabs

located on each side towards the front of the printer, and then lift the top cover to the maximum open angle.

1. Separate the Label Holders by gently

pulling them in opposite directions 2. Insert the media between the label holders as

shown

3. Using the Media Guide Adjuster Knob,

adjust the Media Guide until it is ﬂush but

not tight against the media.

4. To shut the printer, push the support hinge in,

then gently shut the printer, ensuring it latches

shut. Press the Feed button on the printer before

printing, to ensure the tag is printed correctly.

WCM-TT-040-40BB User Manual Wavecom

Loading the Ribbon

To begin, open the printer top cover by pulling the tabs located on each side towards the front of the printer,

and then lift the top cover to the maximum open angle. You will also need to remove the old ribbon (which will

be spooled under the top cover shown in step 1) before loading a new ribbon. To remove this ribbon, simply

hold the ribbon roll and move it to the right (away from the blue gear).

1. Open the top cover of

your Printer

4. Push the ribbon into the right

axle (black), then align the

notches on the left and insert

the ribbon onto the gear (blue)

2. Insert an empty core between the

gear and the axle - ensure the

notches align as shown

3. Open the printer. and get the

thermal transfer ribbon ready.

Ensure the ribbon unwinds from

underneath as shown in Step 5

6. Attach the ribbon to the empty roll uising a piece of

tape - try to attach the ribbon as straight as possible.

5. Next, gently pull the ribbon out, up and over the print head,

around to the empty core.

7. Use the ribbon rewind gear to tighten the ribbon

against the print head, then close the printer.

WCM-TT-040-40BB User Manual Wavecom

Printer Functions

LED and Button Functions

This printer has one button and one three-colour LED indicator. By indicating the LED with different colour and

pressing the button, printer can feed labels, pause the printing job, select and calibrate the media sensor, print

printer self-test report, reset printer to defaults (initialization). Please refer to the button operation below for

different functions.

LED Colour Description

Solid Green This indicates that the power is on and the device is ready to use.

Flashing Green This indicates that the system is downloading data from PC to memory or the printer is paused.

Amber This indicates that the system is clearing data from printer.

Solid Red This illuminates printer head open, cutter error.

Flashing Red This indicates a printing error, such as head open, paper empty, paper jam or memory error etc.

Regular Button Function

Feed labels

When the printer is ready, press the button to feed one label to the beginning of next label.

Pause the printing job

When the printer is printing, press the button to pause a printing job. When the printer is paused, the LED will

be green ﬂashing. Press the button again to continue the printing job.

Power on Utilities

There are six power-on utilities to set up and test printer hardware. To use these utilies follow this procedure:

1. Turn off the power switch.

2. Hold the Feed button then turn on the power switch.

3. The printer LED will cycle through the following options. Release the button when the LED reaches the

relevant utility.

LED Colour & Action

Functions Amber Red

(5 Flashes) Amber

(5 Flashes) Green

(5 Flashes)

Green/

Amber

(5 Flashes)

Red/

Amber

(5 Flashes)

Solid

Green

Gap/Black Mark Sensor

Calibration Release

Gap/Black Mark Sensor

Calibration, Self Test and Enter

Dump Mode Release

Printer Initialisation Release

SetBlackMarkSensorasMedia

Sensor and Calibrate the Black

Mark Sensor Release

SetGapSensorasMediaSensor

and Calibrate the Gap Sensor Release

Skip AUTO.BAS Release

WCM-TT-040-40BB User Manual Wavecom

Gap/Black Mark Sensor Calibration

Gap/black mark sensor sensitivity should be calibrated in the following circumstances:

1. A brand new printer

2. Change label stock

3. Printer initialization

Please follow the steps below to calibrate the gap/black mark sensor.

1. Turn off the power switch.

2. Hold on the button then turn on the power switch.

3. Release the button when LED becomes red and ﬂashing. (Any red will do during the 5 ﬂashes).

4. It will calibrate the gap/black mark sensor sensitivity.

• The LED colour will be changed as following order:

1. Amber

2. Red (5 ﬂashes)

3. Amber (5 ﬂashes)

4. Green (5 ﬂashes)

5. Green/amber (5 ﬂashes)

6. Red/amber (5 ﬂashes)

7. Solid green

Note: Sensor calibration can be done by the power on utility.

Note: Please select gap or black mark sensor type prior to calibrate the sensor.

Gap/Black Mark Calibration, Self-test and Dump Mode

While calibrating the gap/black mark sensor, printer will measure the label length, print the internal

conﬁguration (self-test) on label and then enter the dump mode. To calibrate gap or black mark sensor

depends on the sensor setting in the last print job.

Please follow the steps below to calibrate the sensor.

1. Turn off the power switch.

2. Hold on the button then turn on the power switch.

3. Release the button when LED becomes amber and ﬂashing. (Any amber will do during the 5 ﬂashes)

• The LED colour will be changed as following order.

1. Amber

2. Red (5 ﬂashes)

3. Amber (5 ﬂashes)

4. Green (5 ﬂashes)

5. Green/amber (5 ﬂashes)

6. Red/amber (5 ﬂashes)

7. Solid green

4. The printer will calibrate the sensor and measure the label length and then print the internal settings.

Then it enter Dump Mode.

Note: Sensor calibration can be done by power on utility.

Note: Please select gap or black mark sensor type prior to calibrate the sensor.

WCM-TT-040-40BB User Manual Wavecom

Dump mode

Printer will enter dump mode after printing printer conﬁguration. In the dump mode, all characters will be

printed in 2 columns as following. The left side characters are received from your system and right side data

are the corresponding hexadecimal value of the characters. It allows users or engineers to verify and debug the

program. Dump mode requires 2” wide paper width.

Note:

1. Turn off / on the power to resume printer for normal printing.

2. Press FEED button to go back to the previous menu.

Printer Initialization

Printer initialization is used to clear DRAM and restore printer settings to defaults. Printer initialization is

activated by the following procedures.

1. Turn off the power switch.

2. Hold on the button then turn on the power switch.

3. Release the button when LED turns green after 5 amber ﬂashes. (Any green will do during the 5 ﬂashes).

• The LED colour will be changed as following:

1. Amber

2. Red (5 ﬂashes)

3. Amber (5 ﬂashes)

4. Green (5 ﬂashes)

5. Green/amber (5 ﬂashes)

6. Red/amber (5 ﬂashes)

7. Solid green

Printer conﬁguration will be restored to defaults as below after initialisation.

Parameter Default setting Parameter Default setting

Speed 127 mm/sec (5 ips) (203DPI) 76.2

mm/sec (3 ips) (300DPI) Tear Mode On

Density 8Peel o Mode Off

Label Dimensions 2” (50.8 mm) x 2” (50.8 mm) Cutter Mode Off

Sensor Type Gap sensor Serial Port Settings 9600 bps, none parity, 8 data

bits, 1 stop bit

Gap Setting 0.12” (3.0 mm) Code Page 850

Print Direction 0Country Code 001

Reference Point 0,0 (top left corner) Clear Flash Memory No

Oset 0IP Address DHCP

Indice

Altri manuali Wavecom Stampante

Wavecom

Wavecom TT04- 50 Manuale utente

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente