WE-EF FLB141 #2 Manuale utente
Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.
WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Floodlight
FLB141 #2 LED
1
Floodlight
FLB141 #2
IP66, IK08. Class I. ta = 40°C
Weight kg
for FLB141 #2 LED 3.8
Windage area m²
for FLB141 #2 LED 0.0506
Orientation: all directions
2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
E\DVXLWDEO\TXDOLƂHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.
3
Installation
The product must be installed and maintained by a
VXLWDEO\TXDOLƂHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLƂHGE\DQ\ERG\RWKHU
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.
The installation on site must comply with local and/or
national health and safety regulations.
Important: When mounting luminaires on concrete
or surfaces containing limestone content, WE-EF
recommends using mounting accessories – a short
post or a ground spike to prevent galvanic corrosion.
In areas where mounting accessories are not
applicable, ensure the luminaire’s aluminium base is
separated from concrete and limestone using a plastic
or rubber sheet. Allow concrete to cure before
installation – DO NOT INSTALL ON WET CONCRETE!
Handling: (QVXUHWKHPRXQWLQJƃDQJHSODWHVDUH
handled with care, scratches and damage to the
coated surface can result in galvanic corrosion.
A WE-EF warranty does not cover any adverse reaction
or damage, due to improper installation and requests
that our recommendations are followed.
4
1) Switch off mains electrical supply.
Installation Procedure
'HWHUPLQHSRVLWLRQIRUƂ[LQJVFUHZVD.
Drill relevant holes Eand insert wall plug F.
Attention: Ensure not to damage any electric
cable, water pipe or other devices while drilling
holes.
5HPRYHPRXQWLQJƃDQJHAby loosening
screws B. Disconnect terminal connector C.
2) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
FLB141-LED 220-240V50-60/Hz
161-XXXX SOE XXXXXXX
LED 3000K 18W item no. XXX
07/18 IP66
5
7) Ensure that all surface are clean and dry. Position
OXPLQDLUHRYHUPRXQWLQJƃDQJHAand reconnect
terminal connector C. Turn luminaire towards
object to be illuminated. Tighten screw B.
5) Feed mains supply cable Gthrough the pres-
sure screw IZKLOHVHWWLQJPRXQWLQJƃDQJHA
LQSRVLWLRQ7RƂ[PRXQWLQJƃDQJHA, insert and
tighten screws D. Ensure nylon washers stay
in position. The pre-installed packing ring His
suitable for cable diameters 7 to 9.5 mm. For
larger cable diameters (9 to 12 mm) use the
auxiliary packing ring supplied.
6) Connect mains supply cable Gleads to
respective terminals in terminal connector C:
a) ON/OFF (L = Phase, N = Neutral,
= Earthing)
b) 1-10 V/DALI (L = Phase, N = Neutral,
= Earthing, DA/DA = DALI control line,
D–/D+ = 1-10 V control line).
Tighten pressure screw I.
8) Loosen screws Mslightly. Aim luminaire in
desired direction, retighten screws M.
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel +49 5194 909 0
Fax +49 5194 909 299
info.germany@we-ef.com
WE-EF LUMIERE
France
Tel +33 4 74 99 14 44
Fax +33 4 74 99 14 40
info.france@we-ef.com
WE-EF HELVETICA
Switzerland
Tel +41 22 752 49 94
Fax +41 22 752 49 74
info.switzerland@we-ef.com
WE-EF LIGHTING
United Kingdom
Tel +44 844 880 5346
Fax +44 844 880 5347
info.uk@we-ef.com
WE-EF LIGHTING
Thailand
Tel +66 2 738 9610
Fax +66 2 175 2174
LQIRDVLDSDFLƂF#ZHHIFRP
WE-EF LIGHTING
Australia
Tel +61 3 8587 0444
Fax +61 3 8587 0499
info.australia@we-ef.com
WE-EF LIGHTING
United States of America
Tel +1 724 742 0030
Fax +1 724 742 0035
info.usa@we-ef.com
TO9249W0121 © WE-EF 2019
7HFKQLFDOVSHFLƂFDWLRQVDUH
subject to change.
Indice
Altri manuali WE-EF Proiettore
WE-EF
WE-EF FLA730 LED Manuale utente
WE-EF
WE-EF FLB440 Manuale utente
WE-EF
WE-EF FLB400 Series Manuale utente
WE-EF
WE-EF FLC131 Manuale utente
WE-EF
WE-EF FLA740 LED Manuale utente
WE-EF
WE-EF FLC200 LED Series Manuale utente
WE-EF
WE-EF FLC240 BL Manuale utente
WE-EF
WE-EF FLC200-CC LED Series Manuale utente
WE-EF
WE-EF FLC220 LED Manuale utente
WE-EF
WE-EF FLA730 Manuale
WE-EF
WE-EF FLB141 1 LED Manuale utente
WE-EF
WE-EF FLB141 #2 LED Manuale utente
WE-EF
WE-EF FLB141 #6 LED Manuale utente
WE-EF
WE-EF FLC280 Manuale utente
WE-EF
WE-EF FLC210 LED Manuale utente
WE-EF
WE-EF ULC200 LED Manuale utente
WE-EF
WE-EF FLB141 Manuale utente
WE-EF
WE-EF FLA740 LED Manuale utente
WE-EF
WE-EF FLA740 Manuale utente
WE-EF
WE-EF FLB141 4 LED Specifiche tecniche
