Weaver W10-HD Manuale utente

W10-HD Installation & Operation Manual

10,000 lb. Capacity Overhead

Asymmetric Two Post Lift

Derek Weaver Company, Inc.

2950 SE Loop 820

Fort Worth, TX 76140

817-560-9510

www.derekweaver.com

CONTENTS

Product Features and Specifications ..............................................1

Installation Requirement .............................................................4

Steps of Installation ……………………………………………………………………………….6

Exploded View ...........................................................................25

Test Run ...................................................................................33

Operation Instruction .................................................................35

Maintenance .............................................................................35

Trouble Shooting .......................................................................36

Lift disposal ......................................................................................37

I. PRODUCT FEATURES AND SPECIFICATIONS

CLEAR-FLOOR DIRECT-DRIVED MODEL FEATURES

Model W10-HD (See Fig. 1)

·Direct-drived design, minimize the lift spare parts and breakdown ratio

·Dual hydraulic cylinders, designed and made as ANSI standards, utilizing imported oil

seal in cylinder

·Self- lubricating UHMW Polyethylene sliders and bronze bush

·Single-point safety release, and dual safety design

. Clear-floor design, provide unobstructed floor use

. Overhead safety shut-off device prevents vehicle damage

·Super-asymmetric arms design can fit extremely wide vehicles, stackable rubber pads

. Standard adjustable heights accommodate varying ceiling heights

W10-HD SPECIFICATIONS

Model

Style

Lifting

Capacity

Lifting

Time

Lifting Height

Overall Height

Overall

Width

Between

Columns

Minimum

Pad Height

Motor

W10-HD

Clear-floor

Direct-drived

10,000 lbs

56S

71 1/2’’-84 1/2’’

142-1/2”/150-1/2”

135”

112 1/4”

3 1/2’’-12 1/2’’

2.0 HP

Fig. 1

Please read carefully

before operation!

Arm Swings View

Attention! Please make sure to place the arms in correct

position before car drive in!

Car in

Fig 3

Fig 2

II. INSTALLATION REQUIREMENT

A. TOOLS REQUIRED

Rotary Hammer Drill (Φ19)

Hammer

Level Bar

English Spanner (12")

Ratchet Spanner with Socket (28#)

Wrench set

(8#, 10#, 13#, 14#, 17#, 19#, 24#)

Carpenter’s Chalk

Screw Sets

Tape Measure (7.5m)

Pliers

Socket Head Wrench (3#, 5#, 8#)

Lock Wrench

Fig.4

B. Equipment storage and installation requirements.

The equipment should be stored or installed in a shady, normal temperature,

ventilated and dry place.

C. The equipment should be unload and transfer by forklift.

D. SPECIFICATIONS OF CONCRETE (See Fig. 6)

Specifications of concrete must be adhered to the specification as following.

Failure to do so may result in lift and/or vehicle falling.

1. Concrete must be thickness 6” minimum and without reinforcing steel bars, and

must be dried completely before the installation.

2. Concrete must be in good condition and must be of test strength 3,000psi

minimum.

3. Floors must be level and no cracks.

E. POWER SUPPLY

The electrical source must be 2.0HP minimum. The source cable size must be 2.5mm²

and in good condition of contacting with floor.

Fig. 6

Concrete must be 3,000psi

minimum

Fig.5

6’’

III.STEPS OF INSTALLATION

A. Location of Installation

Check and insure the installation location (concrete, layout, space size etc.) is

suitable for lift installation.

B. Use a carpenter’s chalk line to establish installation layout of base-plate (See Fig.7).

C. Check the parts before assembly.

1. Packaged lift and power unit (See Fig. 8).

2. Move aside the lift with fork lift or hoist, and open the extension packing carefully, take

off the lifting arms and parts box from upper and inside the column, then move them

to location nearby installation site, check the parts according to the shipment parts

list (See Fig.9).

Shipment Parts list

Top Connecting

Assy.

Parts box

Aluminum

Name plate

Extension Column

（Outer Column）

Lifting Arm

Fig. 7

Fig. 8

Fig. 9

Click a line

135”

3. Loose the screws of the upper package stand, take off the upper extension columns,

take out the parts in the inner column and remove the package stand.

4. Move aside the parts and check the parts according to the shipment parts list.

(See Fig.10, 11).

5. Open the bag 1 of parts and check the parts according to parts box list (See Fig. 12).

6. Open the bag 2 of parts and check the parts according to parts bag list (See Fig. 13).

Fig. 10

Parts in the shipment parts list

Fig. 12

Fig. 11

Parts in the parts box (50)

Fig. 13

D. Install parts of extension columns (See Fig. 14).

E. Position powerside column

Lay down two columns on the installation site paralleled, position the power-side

column according to the actual installation site. Usually, it is suggested to install

power-side column on the front-right side from which vehicles are driven to the lift.

This lift is designed with 2-Section columns. Adjustable height according to the ceiling

height and connecting the inner and extension columns.

W10-HD: Not suitable for installation when the height of the workshop is less than

143-4 / 4 "; only low setting installation for height between 143-5 / 4" -151-5 / 8 ";

the height of the workshop is greater than 151 -5/8 ", installation can be in both high

and low setting;

Fig. 14

Indice

Altri manuali Weaver Sistema di sollevamento

Weaver

Weaver W-1500 Manuale utente

Manuali Sistema di sollevamento popolari di altre marche

morse

morse 82H-124 Manuale utente

Braun

Braun NL955 Series Manuale utente

haacon

haacon 1889.10 Manuale utente

Protekt

Protekt AT 252 Manuale utente

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuale utente

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuale utente

Genie

Genie Z-60/34 Manuale utente

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuale utente

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuale utente

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuale di programmazione

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuale di programmazione

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuale di programmazione

BERG

BERG BeNomic EasyLeaf Manuale utente

Powermate

Powermate LiftGate LG-3 Manuale utente

Snorkel

Snorkel TM12 Series Manuale utente

Terberg

Terberg OMNIDEKA Manuale utente

Harmar Mobility

Harmar Mobility AL625 Istruzioni operative

Rotary

Rotary SPO16 Manuale utente