Webasto Telestart T100 HTM Manuale utente
Operating Instructions
EN
Telestart T100 HTM
1About this document
1.1 Purpose of the document
These operating instructions are part of the product and provide the user with
information on the safe operation of the Telestart T100 HTM.
All the functions of the control element are explained in these operating in-
structions.
NOTE
Carefully read through and follow the heater operating instructions and
the safety information contained therein.
NOTE
The actual availability of these functions depends on each installed
heater.
1.2 Using this document
–Before operating the Telestart T100 HTM, carefully read and follow these
operating instructions as well as the operating instructions for the heater.
–Hand over the quick start guide(s) to the subsequent device owner or user.
1.3 Use of symbols and highlighting
Texts with the symbol refer to separate documents which are enclosed or
are available from Webasto at https://dealers.webasto.com.
–Texts with the symbol refer to technical features.
–Texts with the symbol or refer to possible material damage, risk of ac-
cident or injury.
–Texts with the symbol describe a requirement for the following neces-
sary action.
–Texts with the symbol describe an action.
2Warranty and liability
Webasto shall not assume liability for defects or damage that are the result of
the installation and operating instructions being disregarded. This liability exclu-
sion particularly applies for:
–mechanical damage to the equipment
–Maintenance by untrained personnel
–failure to comply with inspection and service instructions
–repairs not carried out by a Webasto service workshop
–conversion of the unit without permission from Webasto
2
–improper use
3General safety information
DANGER
Danger of explosion
In environments with combustible vapours, flammable dust and haz-
ardous goods (e.g., petrol stations, tank facilities, fuel store, coal
bunkers, timber yard or grain warehouses).
uDo not switch on or operate the heater.
DANGER
Danger of poisoning and suffocation
Do not operate the heater in closed rooms that do not have an exhaust
extraction unit.
uDo not switch on or operate the heater, also not with programmed
heating start.
DANGER
Danger of fire
Flammable materials or liquids in the hot air flow.
uKeep the hot air flow free.
DANGER
Risk of injury from the defective unit
Do not operate a defective Telestart T100 HTM and put it out of service
by removing the fuse:
- prolonged heavy smoke development
- unusual burner noise
- smell of fuel
- permanent fault switch-offs with error messages (flash code)
- damaged heater.
uContact a Webasto service workshop.
3
4Intended use
The control element Telestart T100 HTM is currently approved for the following
applications:
Switching Webasto water heaters on and off.
5Overview
1
2
3
4
5
6
7
Housing with transmitter
Display
Arrow push button : Select
the Settings menu
Push button : Switch on
heater or ventilation
Battery housing cover
Arrow push button : Select
the Settings menu
Push button : Switch off
heater or ventilation
NOTE
The following generally applies: Press the and buttons at the
same time to navigate from the information display to the correspond-
ing setting mode. The respective symbol flashes. Change the setting by
pressing and/or . Press buttons and at the same time
again to exit the Setting mode and apply the set values.
5.1 Explanation of the display symbols
Sym-
bol
Function Sym-
bol
Function
Battery empty (full: no battery
symbol display)
Reception display (when trans-
mitting)
Battery at half capacity (full: no
battery symbol display)
HTM Heating Time Manage-
ment
Start-out time Heating
Comfort mode (example of
comfort level 4, area 1 to 5)
Time
4
Sym-
bol
Function Sym-
bol
Function
Operating time Ventilation
6Functional description
The heating time management (HTM)
system calculates the heating time and
the heater switch-on time depending
on the passenger compartment tem-
perature of the vehicle and the selec-
ted comfort level. Follow the setting
options described below.
An optimum signal transmission is achieved in an open area or from elevated
locations. This makes it possible to operate the parking heater at distance of
approximately 1000 m from the vehicle.
When pressing the transmitter, hold it vertically upwards and do not cover the
top (see figure). If a radio transmission takes place between the Telestart T100
HTM transmitter and the receiver, this is indicated by the symbol in the upper
left corner of the display.
If you determine, since there is no feedback, that the operating signal has not
reached the vehicle, it frequently helps to change your location by a few
meters. Reception in built-upareas is limited accordingly.
NOTE
When retrofitting heaters that are installed ex-works, the range of
functions may be limited. Please consult your installation partner about
this.
NOTE
: The signal has been received and forwarded to the heater.
: Error during signal transmission. Move to a different location
and repeat procedure.
5
7Setting up a vehicle heating system
uBefore switching on the heater (with the ignition on), set the vehicle heating
system to “warm”.
uSet the vehicle fan to the lowest setting (lower power consumption).
NOTE
Depending on the type of vehicle, the air-conditioning system can per-
form these settings automatically or partly autonomously. Ask your
specialist dealer to explain the optimum settings.
8Time
8.1 Call up time
Necessary action Indicator
uPress the push button once
until the time is displayed.
8.2 Setting the time
Necessary action Indicator
üThe time is called up.
uPress the and buttons
simultaneously.
uPress the or push button. Set the desired hour.
uPress the and buttons simultaneously.
uPress the and buttons simultaneously. The symbol stops flash-
ing. The heating time is set.
Necessary action Indicator
uPress the or push but-
ton. Set the desired minutes.
uPress the and buttons simultaneously. The symbol stops flashing.
The time is set.
6
9Operating mode
9.1 Calling up the operating mode
NOTE
The ventilation function is optional.
Necessary action Indicator
uPress the push button
three times until the heating
or ventilation symbol is
displayed.
9.2 Setting the operation mode
Necessary action Indicator
üThe heating or ventilation operat-
ing mode is selected.
uPress the and buttons
simultaneously. The indicator
flashes.
uPress the or button. Select heating or ventilation .
uPress the and buttons simultaneously. The operating mode is set.
10 Heating time
10.1 Calling up the heating time
Necessary action Indicator
uPress the push button
four times until the heating
time is displayed.
7
10.2 Setting the heating time
Necessary action Indicator
uPress the and buttons
simultaneously.
uPress the or push
button. Set the desired minutes.
uPress the and buttons simultaneously. The symbol stops flash-
ing. The heating time is set.
11 Switch on the heater
11.1 Hand-held transmitter
Necessary action Indicator
uPress the button.
: The signal has been received
and forwarded to the heater.
As a switch-on check, the display shows the symbol for operation and the re-
maining operation time (heating time in the example is 30 minutes).
12 Switching off the heater
Necessary action Indicator
uPress the button.
The heating or ventilation
symbol goes out.
12.1 Switching on and off with the push button
üThe parking heater or parking ventilation mode is
displayed on the push button.
uPress the push button (switch the heater or vent-
ilation on or off).
8
13 Pairing the hand-held transmitter
The hand-held transmitter Telestart T100 HTM must be paired with the Tele-
start receiver in the vehicle.
13.1 Determining the installation position of the fuse
Depending on the heater and its installation or application, the Telestart fuse is
installed in the engine compartment or the vehicle interior.
13.2 Teaching the unit
uInsert battery in the battery compartment of the
hand-held transmitter.
> 1 s
uPress the OFF push button (hold it for at least 1
s). The hand-held transmitter has now been
taught.
14 HTM Heating-Time-Management
Information regarding the heating time:
We recommend matching the heating time to the driving time (heating
time = driving time)
Example: for a driving time of approx. 20 min. (in one direction), we re-
commend not exceeding a switch-on time of 20 min.
Heating time management / enables automatic preheating (not ventila-
tion) of the vehicle for a selected start-out time.
The system determines the preheating time of the parking heater depending
on the passenger compartment temperature of the vehicle.
The passenger compartment temperature reached at the start-out time can be
influenced by 5 comfort levels (C1 to C5). C1 is the lower comfort temperature
(short operating time) and C5 is the higher comfort temperature (long operat-
ing time). The start-out time can be activated up to 24 hours in advance.
14.1 Displaying the comfort level
9
Necessary action Indicator
uPress the push button three
times until the comfort level is dis-
played.
14.2 Changing the comfort level
NOTE
The start-out time must first be deactivated. See "Deactivating the
start-out time on page 11".
Necessary action Indicator
üThe comfort level has been selec-
ted.
uPress the and buttons
simultaneously. The comfort level
symbol flashes
uPress the or push button. Set the desired
comfort level.
uPress the and buttons simultaneously. The comfort level symbol
stops flashing.
The comfort level is set.
14.3 Calling up the start-out time
Necessary action Indicator
uPress the push button two
times until the start-out time
is displayed.
10
Altri manuali per Telestart T100 HTM
2
Indice
Altri manuali Webasto Telecomando
Webasto
Webasto ThermoConnect TCon2 Manuale utente
Webasto
Webasto Telestart T70 Manuale utente
Webasto
Webasto Telestart T100 HTM Manuale utente
Webasto
Webasto Telestart T91 Manuale
Webasto
Webasto Telestart T91 Holiday Manuale utente
Webasto
Webasto Telestart T91 Manuale utente
Webasto
Webasto BlueHeat T91 Manuale utente
Webasto
Webasto Telestart T91 Manuale utente
Webasto
Webasto ThermoCall TC4 Manuale utente
Webasto
Webasto Telestart T91 Manuale utente
