Weidmüller IE-SW-BL05-5GT Manuale

Gigabit Ethernet Switch – Basic Line

IE-SW-BL05-5GT

Hardware Installation Guide

Third Edition, July 2011

1243380000/02/07.11

Please note:

This document and any further product information - if

available - can be downloaded at the internet link:

http://www.weidmueller.com/downloads

Reproduction without permission is prohibited.

Overview

The IE-SW-BL05-5GT is equipped with 5 Gigabit Ethernet ports, making it an

ideal and economical solution for demanding, high bandwidth Gigabit Ethernet

applications. In addition, the built-in relay warning function alerts system

administrators when power failures or port breaks occur. The switches have

passed a 100% burn-in test to ensure that they fulfill the special needs of

industrial automation control and can be easily installed with DIN-Rail

mounting as well as distribution boxes.

Package Checklist

Your Ethernet Switch is shipped with the following items. If any of these items

is missing or damaged, please contact your Weidmüller customer service for

assistance.

yEthernet Switch

yHardware Installation Guide

Features

High Performance Network Switching Technology

y10/100/1000BaseT(X) (RJ45), auto negotiation speed, F/H duplex mode

yIEEE 802.3/802.3u/802.3ab.

yStore and Forward switching process type, 8K MAC address entries.

Industrial Grade Reliablity

yPower failure, port break alarm by relay output

yRedundant dual 12/24/48VDC power inputs

Rugged Design

yStandard operating temperature range from 0 to 60°C or extended

operating temperature of -40 to 75°C for (-T) models

yIP30, rugged high-strength case

yDIN-Rail or panel mounting ability

- 2 -

Panel Layout of

IE-SW-BL05-5GT

1. Grounding screw

2. Terminal block for power input

(PWR1, PWR2) and relay output

3. Power input PWR1 LED

4. Power input PWR2 LED

5. Fault LED

6. TP port’s 10/10/1000 Mbps LED

7. Port number

8. 10/100/1000BaseT(X) Port

9. Article Number

10. DIP switches

11. Heat dissipation orifices

12. Screw hole for wall mounting kit

13. DIN-Rail Kit

- 3 -

Mounting Dimensions (unit = mm)

DIN-Rail Mounting

The aluminum DIN-rail attachment plate should already be fixed to the back

panel of the Ethernet Switch when you take it out of the box. If you need to

reattach the DIN-rail attachment plate, make sure the stiff metal spring is

situated towards the top, as shown in the figures below.

STEP 1:

Insert the top of the DIN-rail into the

slot just below the stiff metal spring.

STEP 2:

The DIN-rail attachment unit will

snap into place as shown below.

metal

spring

DIN-Rail

metal

spring

DIN-Rail

To remove the DIN-rail from the Ethernet Switch, simply reverse Steps 1 and

Wall Mounting (optional)

For some applications, you will find it convenient to mount the Ethernet

Switch on the wall, as illustrated below.

STEP 1:

Remove the aluminum

DIN-rail attachment plate

from the Ethernet Switch

rear panel, and then attach

the wall mount plates, as

shown in the figure. ⇒

- 4 -

STEP 2:

Mounting the Ethernet S

screws. Use the switch, wit

as a guide to mark the corr

The heads of the screws sho

diameter, and the shafts sh

diameter, as shown in

witch on the wall requires 4

h wall mount plates attached,

ect locations of the 4 screws.

uld be less than 6.0 m

ould be less than 3.5 mm

the figure at the right.

m in

6.0 mm

3.5 mm

NOTE Before tightening screws into the wall, make sure the screw head

and shank size are suitable by inserting the screw into one of the

keyhole-shaped apertures of the Wall Mounting Plates.

Do not screw the screws in all the way—leave about 2

sliding the wall mount panel between the wall and the scre

STEP 3:

Once the screws are fixed in

mm to allow room for

ws.

insert the four screw

apertures

Ethernet

en the four

the wall,

heads thr

of the key

ough the large parts

hole-shaped

, and then slide the

Switch downwards, ⇒

as indicated. Tight

screws for added stability.

II 3G

ATE

Certificate number DEM

X Information

1. KO 11 ATEX 150192X

2. Ambient range (-40°C ≤Tamb ≤75°C)

3. Certification string (Ex nC nL IIC T4)

4. Standards covered (EN60079-0:2006, EN60079-15:2005)

The conditions of safe usage:

• These products must be mounted in an IP54 enclosure.

• Install in an area of pollution degree 2 or less.

• A 4mm2 conductor must be used when connection to the external

grounding screw is utilized.

• PROVISIO

APPARATU FROM

URBANCES OF

NS SHOULD BE MADE, EXTERNAL TO

S, TO PREVENT THE RATED VOLTAGE

THE

BEING EXCEEDED BY TRANSIENT DIST

MORE THAN 40 %.

- 5 -

Wiring Requirements

WARNING

Safety First!

Turn the power off before disconnecting modules or wires. Th

proper power supply

the voltage of your power

voltage is listed on the product label. Check

source to make sure you are using the

correct voltage. Do NOT use a voltage greater than what is

specified on the product label.

These devices must be supplied by an AELV source as defined in

the Low Voltage Directive 2006/95/EC and 2004/108/EC.

WARNING

Safety First!

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

Use separate paths to route wiring for power and devices. If power wiring

and de s must cross, make sure the wires are perpendicular

at the intersec

NOTE al or communications wiring and power wiring in

the sam

charac

yYou can use the type of signal tran mine

which h

similar

Keep input wiring and output wiring separated.

stem

ele

gro onnecting devices.

You should also p

ay attention to the following items:

vice wiring path

tion point.

: Do not run sign

e wire conduit. To avoid interference, wires with different signal

teristics should be routed separately.

smitted through a wire to deter

wires should be kept separate. The rule of thumb is that wiring wit

electrical characteristics can be bundled together.

It is strongly advised that you label wiring for all devices in the sy

when necessary.

rounding Ethernet Switch

ounding and wire routing help limit the effects of noise due to

ctromagnetic interference (EMI). Run the ground connection from the

und screw to the grounding surface prior to c

ATTENTION

This product is intended to be mounted to a well-grounded

mounting surface, such as a metal panel.

- 6 -

Wiring the Alarm Contact

The Alarm Contact consists of the two middle contacts of the terminal blo

the Ethernet Switch top panel. You may refer to the next section for detaile

instructions on how to connect the wires to the terminal block conne

ck on

ctor, and

how to attach the terminal block connector to the terminal block receptor.

In this sec meaning of the two contacts used to connect the

Alarm Con

tion, we explain the

tact.

FAULT: The two m

FAULT

Top View

Front View

If neither of these two conditions is satisfied,

iddle contacts of the

6-contact terminal block connector are used to

detect both power faults and port faults. The

two wires attached to the Fault contacts form

an open circuit when:

s lost power from one of

ts.

the Fault circuit will be closed.

Wiring the Redu

The top two contacts and the bo

block connector on the Ethernet Switch the Ethernet

Switch DC inputs. Top and fron

are shown here.

1. Ethernet Switch ha

the DC power inpu

2. The PORT ALARM DIP switch for one o

the ports is set to ON, but the port is not

connected properly.

ndant Power Inputs

ttom two contacts of the 6-contact terminal

top panel are used for

t views of one of the terminal block connectors

STEP 1: Insert the negative/positive DC

wires into the V-/V+ terminals.

STEP 2: To keep the DC wir

Top View

Front View

connector prongs into the terminal block

receptor, which is located on Ethernet

Switch top panel.

es from

inal block

connector.

pulling loose, use a small flat-blade

screwdriver to tighten the wire-clamp

screws on the front of the term

STEP 3: Insert the plastic terminal bloc

ATTENTION

Before connecting the Ethernet Switch to the DC power inputs,

make sure the DC power source voltage is stable.

- 7 -

Communication C

IE-SW-BL05-5GT has 5 10/100/10 BaseT(X) Ethernet ports

10/100/1000BaseT(X

Connection

The 10/100/1000BaseT(X) ports lo

used to connect to Ethernet-enabled will choose to

configure these ports for Auto MDI

pinouts are adjusted automatically d

used (straight-through or cross-over

HUB/Switch-type) conne d to the

what follows, we give pinouts for ype) ports and MDI-X

type) ports. We also give cable wiring diagrams for

straight-thr er Ethernet cables.

10 /100Ba

MDI Port Pinouts MDI-X Port Pinouts 8-pin RJ45

Pin Signal Pin Signal

onnections

) Ethernet Port

cated on Ethernet Switch’s front panel are

evices. Most users

/MDI-X mode, in which case the port’s

epending on the type of Ethernet cable

), and the type of device (NIC-type or

port.

both MDI (NIC-t

cte

(HUB/Switch-

ough and cross-ov

se T(x) RJ45 Pinouts

1 Tx+ 1 Rx+

2 Tx- 2 Rx-

3 Rx+ 3 Tx+

6 Rx- 6 Tx-

1000BaseT RJ45 Pinouts

Pin MDI MDI-X

1 BI_DA+ BI_DB+

2 BI_DA- BI_DB-

3 BI_DB+ BI_DA+

4 BI_DC+ BI_DD+

5 BI_DC- BI_DD-

6 BI_DB- BI_DA-

7 BI_DD+ BI_DC+

8 BI_DD- BI_DC-

- 8 -

RJ45 n) (8 ight-Through Cable Wiring

(8-pi to RJ45 -pin) Stra

Straight-Through Cable

Pin 1

RJ45 Plug

Switch

onne RJ45

Connecto

Port

J45

C ctor

Tx+

Tx-

Rx+

Rx-

DD+

DD-

DC+

DC-

NIC Port

le Wiring

Cab Rx+

Rx-

Tx+

Tx-

DC+

DC-

DD+

DD-

J45 (8-pin) to RJ45 (8-pin) Cross-Over Cable WiringR

Cross-Over Cable

RJ45 Plug Pin 1

Switch Port

(NIC Port)

RJ45

Connector RJ45

Connector

Tx+

Tx-

Rx+

Rx-

(Rx+)

(Rx-)

(Tx+)

(Tx-) DC+

DC-

DD+

DD-

(DD+)

(DD-)

(DC+)

(DC-)

(Tx+)

(Tx-)

(Rx+)

(Rx-)

Switch Port

(NIC Port)

Cable Wiring

Rx+

Rx-

Tx+

Tx- (DC+)

(DC-)

(DD+)

(DD-)

DD+

DD-

DC+

DC-

Redundant Power Inputs

Both power inputs can be connected simultaneously to live DC power sources.

If one power source fails, the other live source acts as a backup, and

automatically supplies all of the Ethernet Switch power needs.

Alarm Contact

The Ethernet Switch has one Alarm Contact located on the top panel. For

detailed instructions on how to connect the Alarm Contact power wires to the

two middle contacts of the 6-contact terminal block connector, see the Wiring

be to connect

the Fault circuit to a warning light located in the control room. The light can be

set up to switch on when a fault is detected.

The Alarm Contact has two terminals that form a Fault circuit for connecting to

an alarm system. The two wires attached to the Fault contacts form an open

circuit when (1) Ethernet Switch has lost power from one of the DC power

inputs, or (2) one of the ports, for which the corresponding PORT ALARM

DIP switch is set to ON, is not properly connected.

If neither of these two conditions occurs, the Fault circuit will be closed.

the Alarm Contact section on page 6. A typical scenario would

- 9 -

DIP Switch Settings

BSP

----

ONOFF

ON DIP

12345

PORT

ALARM

OFF ON

DIP Switch Setting

The default setting for each DIP switch is OFF. The

following table explains the effect of setting the

switches to the ON positions.

Description

DIP

ON Enables broadcast storm protection

BSP OFF Disables broadcast storm protection

ON Enables jumbo frame function

----

refers to Jumbo

Frame OFF Disables jumbo frame function

. If

the port’s link fails, the relay will form an

open circuit and the fault LED will light up.

Enables the corresponding PORT Alarm

PORT Alarm Disables the corresponding PORT Alarm.

y will form a closed circuit and the

D will never light up.

OFF The rela

Fault LE

ATTENTION

To actively update DIP switch settings, power off and then power

on the Ethernet Switch.

- 10 -

Indice

Altri manuali Weidmüller Interruttore

Weidmüller

Weidmüller 2682340000 Manuale

Weidmüller

Weidmüller IE-SW-AL08M-8TX Manuale

Weidmüller

Weidmüller IE-SW-EL10-8GT-2GESFP Manuale

Weidmüller

Weidmüller Gigabit Advanced IE-SW-AL06M-4GTPoE-2GESFP Manuale

Weidmüller

Weidmüller IE-SW-BL05-4GT-1GS Manuale

Weidmüller

Weidmüller IE-SW-AL08M-8GT Manuale

Weidmüller

Weidmüller 2682340000 Manuale

Weidmüller

Weidmüller Gigabit Advanced IE-SW-AL08M-8GTPoE Manuale

Weidmüller

Weidmüller Substation IE-SW-SL26M-24TX-2GC Manuale utente

Weidmüller

Weidmüller IE-SW-EL08-8GT Manuale

Weidmüller

Weidmüller IE-SW-SL28M Manuale utente

Weidmüller

Weidmüller Value Line IE-SW-VL05M Series Manuale

Weidmüller

Weidmüller Premium Line IE-SW-PL08M Series Manuale

Weidmüller

Weidmüller IE-SW-AL08M-8GT Manuale

Weidmüller

Weidmüller Basic Line IE-SW-BL05-4GTPoE Series Manuale

Weidmüller

Weidmüller IE-SW-EL05-5TX Manuale

Weidmüller

Weidmüller PV Next Series Manuale utente

Weidmüller

Weidmüller IE-SW-EL16-14TX-2FESFP Manuale

Weidmüller

Weidmüller IE-SW-EL08-6TX-2SC Manuale

Weidmüller

Weidmüller IE-SW-AL08M-8GT Manuale utente

Weidmüller

Weidmüller Premium Line IE-SW-PL10M Series Manuale

Weidmüller

Weidmüller Premium Line IE-SW-PL10M Series Manuale

Weidmüller

Weidmüller IE-SW-EL08-8GTPoE Manuale

Weidmüller

Weidmüller IE-SW-EL10-8GTPoE-2GESFP Manuale

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente