Weidmuller SpeedMarking-Laser Manuale utente
SpeedMarking-Laser
User's Manual
Foreword
5658600000/00/05.07 3
Foreword
Revisions
Version Date Modification
0.0 05/07 First release
Range of delivery
Please check to ensure that your SpeedMarking-
Laser is complete. Your SpeedMarking-Laser should
contain the following parts.
•Special packing SpeedMarking-Laser
•SpeedMarking-Laser
•Toner
•Parallel printer cable
•Power cord
•User's Manual
•CD with software and driver
Installation instructions
This manual contains important information for in-
stalling and initial start-up procedures for the
SpeedMarking-Laser.
You can find here information about the installation,
setup and remedy of defects of the SpeedMarking-
Laser.
For more information, useful tips, or the latest driv-
ers, check our homepage at:
www.weidmueller.com
Follow the Downloads →Printer Drivers →Speed
Marking Laser links.
You can also send us an e-mail at
Contact address
Weidmüller Interface GmbH & Co. KG
Postfach 3030
32720 Detmold
Klingenbergstraße 16
32758 Detmold, Germany
Phone +49 (0) 5231 14-0
Fax +49 (0) 5231 14-2083
E-Mail [email protected]
Internet www.weidmueller.com
Contents
4 5658600000/00/05.07
Contents
Foreword ............................................................................................................................3
Revisions.............................................................................................................................3
Range of delivery.................................................................................................................3
Installation instructions.........................................................................................................3
Contact address...................................................................................................................3
Contents.............................................................................................................................4
1. Safety instructions................................................................................................6
2. Printer installation.................................................................................................8
2.1 Printer components.................................................................................................8
2.2 Setting up the printer...............................................................................................9
2.3 Unpacking the printer............................................................................................10
2.4 Insertion of toner cartridge ....................................................................................10
2.5 Connection of printer cable ...................................................................................11
2.6 Connection of mains cable....................................................................................12
2.7 Installation of printer driver....................................................................................12
3. Basic information of the printer.........................................................................14
3.1 Printer functions....................................................................................................14
3.2 Operating panel.....................................................................................................15
3.3 Operating panel buttons........................................................................................15
3.4 LED displays.........................................................................................................16
3.5 Switch for printing SF markers..............................................................................17
3.6 Printer drivers........................................................................................................17
3.7 Accessories and ordering information...................................................................18
4. Printing jobs........................................................................................................19
4.1 Printing of adhesive backing markers ...................................................................19
4.2 Printing preparation...............................................................................................19
4.3 Printing jobs ..........................................................................................................20
Contents
5658600000/00/05.07 5
5. Printer tips and maintenance.............................................................................21
5.1 Improvement of printing ........................................................................................21
5.2 Extend the lifespan of the special-toner cartridge .................................................21
5.3 Maintenance of special-toner cartridge.................................................................21
5.4 Printer maintenance..............................................................................................22
6. Troubleshooting..................................................................................................23
6.1 Fuses....................................................................................................................23
6.2 Overheating shutoff...............................................................................................23
6.3 Remedy for congestion.........................................................................................23
6.4 Problems with the printing quality..........................................................................25
6.5 Checklist for troubleshooting.................................................................................26
7. Guarantees ..........................................................................................................28
7.1 Limited guarantee .................................................................................................28
7.2 Guarantee exclusions ...........................................................................................28
7.3 Restriction of liability .............................................................................................28
7.4 Customer support during and after the guarantee period......................................29
7.5 Packaging instructions..........................................................................................29
7.6 Guarantee for toner...............................................................................................29
8. Printer specifications..........................................................................................30
8.1 Environmental conditions......................................................................................30
8.2 Consumables........................................................................................................31
Safety instructions
6 5658600000/00/05.07
1. Safety instructions
Read the following instructions carefully be-
fore starting up the SpeedMarking-Laser.
Observe the warnings and notices on the
SpeedMarking-Laser at all times.
•The mains voltage must correspond to
the system voltage given on the Speed-
Marking-Laser type plate.
•Connect the device to a properly earthed
and fused socket outlet only. Do not use
a socket outlet already being used by
devices that are turned on and off at
regular intervals, such as photocopiers
or ventilators.
•Do not connect the SpeedMarking-Laser
to either a switched or a timer-controlled
socket outlet.
Do not use the computer system close to
potential electromagnetic disturbance
fields such as loudspeakers or base trans-
ceiver stations for mobile telephones.
If you connect the SpeedMarking-Laser to
the power supply via an extension cable,
ensure that the total nominal current of all
of the devices connected to the extension
cable does not exceed the capacity for that
extension cable. In addition, you should
ensure that the total nominal current of all
the devices plugged into the wall-mounted
socket outlet does not exceed the ampere
rating for that socket outlet.
Do not carry out repairs to the device your-
self.
•Never use damaged or worn out power
cables.
•Connect the device to the mains only
with cable described in this guide.
•Avoid the usage of multiple cables.
•Connect the network cable directly
(never via an extension cable) to the
power socket.
•Keep the mains cable undamaged and
keep it in its original state. Do not place
any heavy objects on it. Do not pull at it
with force and do not bend it more than
necessary. A disregard of these instruc-
tions can lead to electrocution or fire.
•Place the device close to an accessible
power socket in order to be able to pull
the mains plug in case of an emergency.
•Never connect or disconnect the mains
plug to the power socket with wet hands.
There is a risk of electrocution.
Disconnect the SpeedMarking-Laser and
contact a qualified service engineer if any
of the following occurs:
•The power cord or plug are worn or dam-
aged.
•A fluid has penetrated into the Speed-
Marking-Laser.
•The SpeedMarking-Laser is allowed to
fall or the enclosure is damaged.
•The SpeedMarking-Laser does not oper-
ate normally or the standard of perform-
ance varies noticeably.
Keep any moisture or dust off the device.
Otherwise, there is the danger of fire or
electrocution.
Safety instructions
5658600000/00/05.07 7
•Do not spill any fluids into the Speed-
Marking-Laser.
•Place the device onto a solid, flat sur-
face. Otherwise, it could fall down and
lead to possible danger to personnel.
•For installation in limited space, make
sure that there is sufficient ventilation for
the device.
•Do not block or cover openings of the
SpeedMarking-Laser.
•Do not insert any objects into these
openings.
This device is not to be operated with-
out supervision.
The internally-emitting radiation is kept in-
side the printer by the protective housing
and the external cover. The laser beam
cannot emit from the device during opera-
tion.
The printer cannot be used or maintained if
the protective cover is taken off the laser or
scanner unit. The reflective beam is invisi-
ble and can damage the eyes.
Warning signs (BGV A 8 (VBG 125) & DIN 4844)
WARNING
Mind your hands.
Do not reach inside.
WARNING
Hot surface.
Do not touch.
Printer installation
8 5658600000/00/05.07
2. Printer installation
This chapter is for the setup and installation of the
new SpeedMarking-Laser.
Follow after unpacking the printer the listed steps in
the checklist in its exact order. Each step is de-
scribed in detail with easily understandable specifi-
cations.
2.1 Printer components
A B
C
Figure 1 Front side
A Cover
B Operating panel
C Output
A B
Figure 2 Rear side
A Parallel interface
B On/Off switch and mains connection
A
Figure 3 Rear side
A Input
Printer installation
5658600000/00/05.07 9
2.2 Setting up the printer
•Place the device onto a solid, flat surface.
•Provide sufficient ventilation.
•The ambient conditions should be stable, e.g. the temperature and humidity fluctuations should be limited
(Temperature: 20 °C – 35 °C; Humidity: 55% – 75%).
•Avoid direct sunlight on the printer.
•The environment of the printer should be free of any chemicals.
The following dimensions show the space required for setting up the printer.
Figure 4 Space in front of and behind the printer
Figure 5 Space on both sides of the printer
Make sure that there is enough space in order:
•to open the upper cover
•to load material into the entry
•to empty the storage tray
•to be able to access the on/off switch
•to connect the mains and printer connection
•to use the operating panel
Printer installation
10 5658600000/00/05.07
2.3 Unpacking the printer
Store all packaging material.
In case of repairs you should return the
printer in its original packaging to avoid any
possible damage in transit.
2.4 Insertion of toner cartridge
Figure 6 Opening the upper cover
1 Open the upper cover
2 Remove the transport retainer that is situated be-
low the cover of the SpeedMarking-Laser.
3 Take the toner cartridge out of its packaging.
Figure 7 Removal of toner cartridge out of pack-
aging
4 Remove the alignment rod for the roller.
Figure 8 Remove alignment rod for the roller
Caution
To avoid any damages, the toner cartridge
should be exposed to the sunlight only for
a few minutes.
5 Follow for steps 5-6 the instructions on the roller.
Figure 9 Roller
6 Do not position the toner cartridge upside down
and do not shake it.
Indice
Altri manuali Weidmuller Stampante
