Westermo MRD-315 Manuale utente

©Westermo Teleindustri AB

MRD-315, MRD-355 & MRD-455

Industrial Mobile Broadband Router

GSM / GPRS / EDGE / 3G /

HSDPA / HSUPA / HSPA / 4G LTE

www.westermo.com

User Guide

6623-2250

Legal information

The contents of this document are provided “as is”. Except as required by applicable

law, no warranties of any kind, either express or implied, including, but not limited to,

the implied warranties of merchantability and fitness for a particular purpose, are made

in relation to the accuracy and reliability or contents of this document. Westermo

reserves the right to revise this document or withdraw it at any time without prior

notice.

Under no circumstances shall Westermo be responsible for any loss of data or income

or any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at the following Internet address:

http://www.westermo.com

6623-2250

Safety

Before using this unit:

Read this manual completely and gather all information on the unit. Make sure

that you understand it fully. Check that your application does not exceed the safe

operating specifications for this unit.

Hazardous voltages may occur within this unit when connected to a power supply.

Prevent access to hazardous voltages by disconnecting the unit from its power

supply.

Prevent damage to internal electronics from electrostatic discharges (ESD) by

discharging your body to a grounding point (e.g. use of wrist strap).

Before installation:

This unit should only be installed by qualified personnel.

This unit should be built-in to an apparatus cabinet, or similar, where access is

restricted to service personnel only.

The power supply wiring must be sufficiently fused, and if necessary it must be

possible to disconnect manually from the power supply. Ensure compliance to

national installation regulations.

This unit uses convection cooling. To avoid obstructing the airflow around the unit,

follow the spacing recommendations (see Installation section).

Care recommendations

Follow the care recommendations below to maintain full operation of unit and to fulfil

the warranty obligations.

This unit must not be operated with covers or lids removed.

Do not attempt to disassemble the unit. There are no user serviceable parts inside.

Do not drop, knock or shake the unit, rough handling beyond the specification may cause

damage to internal circuit boards.

Do not use harsh chemicals, cleaning solvents or strong detergents to clean the unit.

Do not paint the unit. Paint can clog the unit and prevent proper operation.

Do not expose the unit to any kind of liquids (rain, beverages, etc). The unit is not

waterproof. Keep the unit within the specified humidity levels.

Do not use or store the unit in dusty, dirty areas, connectors as well as other mechanical

part may be damaged.

If the unit is not working properly, contact the place of purchase, nearest Westermo

distributor office or Westermo Tech support.

GSM specific safety

Please read and follow the guidelines listed below. The precautions must be observed

during all phases of the operation. Breaking these rules may be dangerous, illegal or affect

performance of the unit and/or invalidate the unit’s approval and/or warranty.

6623-2250

General

Remember to follow any special regulations and warnings in force in any area and never

use the unit whenever it’s forbidden to use it. Do not use the unit when it may cause

interference or danger. A wireless device exposed to interference above specified limits

could result in deteriorated performance.

Hospitals or other Medical environment

Do not use the unit in a medical environment such as health care facilities. Follow any

regulations or rules that instruct you to not use the unit.

Pacemakers

The Health Industry Manufacturers Association recommends that a minimum separation

of six (6”) inches be maintained between cellular wireless equipment and a pacemaker to

avoid potential interference with the pacemaker. These recommendations are consistent

with the independent research by and recommendations of-Wireless Technology

Research.

Persons with pacemakers:

… Should ALWAYS keep the the unit and its antenna more than six inches from their

pacemaker when the unit is turned ON.

… If you have any reason to suspect that interference is taking place, turn your wireless

equipment OFF immediately.

Hearing Aids

Some digital wireless equipment may interfere with some hearing aids. In the event of

such interference, you may want to consult your service provider [or call the customer

service line to discuss alternatives.]

Other Medical Devices

If you use any other personal medical device, consult the manufacturer of your device to

determine if they are adequately shielded from external RF energy.-Your physician may be

able to assist you in obtaining this information.

Turn the wireless equipment OFF in health care facilities when any regulations posted

in these areas instruct you to do so. Hospitals or health care facilities may be using

equipment that could be sensitive to external RF energy.

Aircraft

Do not use the unit in an aircraft. The use of a wireless unit in an aircraft may be

dangerous to the operation of the aircraft, disrupt the wireless network, and may be

illegal.

Failure to observe these instructions may lead to suspension or denial of cellular services

to the offender, legal action, or both.

Vehicle

If the unit is incorrectly installed in a vehicular environment, the operation of the unit

could interfere with the vehicle electronics. Faulty installation and/or operation can

constitute a safety hazard.

6623-2250

For Vehicles equipped with an airbag

An air bag inflates with great force. DO NOT place objects, including either installed or

portable wireless equipment, in the area over the air bag or in the air bag deployment

area. If in-vehicle wireless equipment is improperly installed and the air bag inflates,

serious injury could result.

Blasting areas

Do not use the unit where blasting is in progress or in “blasting areas”. Observe

restrictions and follow any regulation or rules.

Explosive atmospheres

Do not use the unit in any area with a potentially explosive atmosphere. Potentially

explosive areas are often, but not always, clearly marked. They include fuelling areas such

as petrol stations, below decks on boats, fuel or chemical transfer or storage facilities,

and areas where the air contains chemicals or particles, such as grain, dust, or metal

powder.

RF energy

The unit is a low power radio transmitter and receiver. When it is ON, it receives

and also sends out radio frequency (RF) signals. Most modern electronic equipment is

shielded from RF signals. However, certain electronic equipment may not be shielded

against the RF signals from the wireless unit. All radio-transmitting devices send signals,

which may cause interference in different electronic devices. To avoid interference, place

the units antenna a sufficiently long distance from other electronics.

Critical applications

Cellular units operate using radio signals and cellular networks cannot be guaranteed to

connect in all conditions. Therefore you should never rely solely on a wireless device for

essential communications, for example medical emergencies.

Backup copies

Remember to make backup copies of all important data, for example PIN/PUK codes,

contents of SIM card etc.

Antenna care

Use only the supplied or an approved replacement antenna. Unauthorized antennas,

modifications, or attachments could damage the unit and may violate current regulations.

Do not touch the antenna unnecessarily when the unit is in use. Contact with the

antenna affects call quality and may cause the unit to operate at a higher power level

than otherwise needed.

Maintenance

No maintenance is required, as long as the unit is used as intended within the specified

conditions.

6623-2250

Type Approval/Compliance

EMC

EN 55022, EN 55022 A1,

Information technology equipment.

Radio disturbance characteristics.

Limits and methods of measurement

EN 55024, EN 55024 A1, EN 55024 A2,

Electromagnetic compatibility – Immunity IT equipment

Safety IEC/EN 60950-1, IT equipment

R&TTE

Article 3.1a EN 60950-1 Safety

EN 50385 EMF exposure

Article 3.1b EN 301 489-1 ERM/EMC

EN 301 489-7 ERM/EMC GSM

EN 301 489-24 ERM/EMC 3G

Article 3.2 EN 301 908-1 ERM 3G

EN 301 908-2 ERM 3G

EN 301 511 GSM

Agency approvals and standards compliance

6623-2250

Declaration of Conformity, MRD 315

Westermo Teleindustri AB

Declaration of conformity

Org.nr/

Postadress/Postal address

Tel.

Telefax

Postgiro

Bankgiro

Corp. identity number

Registered office

S-640 40 Stora Sundby 016-428000 016-428001 52 72 79-4 5671-5550 556361-2604 Eskilstuna

Sweden Int+46 16428000 Int+46 16428001

The manufacturer Westermo Teleindustri AB

SE-640 40 Stora Sundby, Sweden

Herewith declares that the product(s)

Type of product Model Art no

3G Cellular Modem / Router MRD 315 3623-0050

is in conformity with the following EC directive(s).

No Short name

1999/5/EC Radio equipment and Telecommunications terminal equipment (R&TTE)

2011/65/EU Restriction of the use of certain hazardous substances in electrical and electronic equipment

(RoHS)

References of standards applied for this EC declaration of conformity.

No Title Issue

EN 50385 Product standard to demonstrate the compliance of radio base stations and fixed

terminal stations for wireless telecommunication systems with the basic

restrictions or the reference levels related to human exposure to radio frequency

electromagnetic fields (110 MHz - 40 GHz) - General public

2002

EN 50581 Technical documentation for the assessment of electrical and electronic products

with respect to the restriction of hazardous substances

2012

EN 60950-1 Information technology equipment. Safety. General requirements 2006

+A11:2009

+A1:2010

+A12:2011

+A2:2013

EN 301 489-1

EN 301 489-7

EN 301 489-24

Electromagnetic compatibility and radio spectrum matters (ERM);

Electromagnetic compatibility (EMC) standard for radio equipment and services

Part 1: Common technical requirements

Part 7: Specific conditions for mobile and portable radio and ancillary equipment

of digital cellular radio telecommunications systems (GSM and DCS)

Part 24: Specific conditions for IMT-2000 CDMA Direct Spread (UTRA) for

Mobile and portable (UE) radio and ancillary equipment

2012 (V1.9.2)

2006 (V1.3.1)

2010 (V1.5.1)

EN 301 511 Global system for mobile communications (GSM); Harmonized standard for

mobile stations in the GSM 900 and DCS 1800 bands covering essential

requirements under Article 3(2) of the R&TTE Directive (1999/5/EC)

2003 (V9.0.2)

EN 301 908-1

EN 301 908-2

IMT cellular networks; Harmonized EN covering the essential requirements of

article 3.2 of the R&TTE Directive;

Part 1: Introduction and common requirements

Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)

2013 (V6.2.1)

2014 (V6.2.1)

The last two digits of the year in which the CE marking was affixed: 15

Pierre Öberg

Technical Manager

Mars 2015

6623-2250

Declaration of Conformity, MRD 355

Westermo Teleindustri AB

Declaration of conformity

Org.nr/

Postadress/Postal address

Tel.

Telefax

Postgiro

Bankgiro

Corp. identity number

Registered office

S-640 40 Stora Sundby 016-428000 016-428001 52 72 79-4 5671-5550 556361-2604 Eskilstuna

Sweden Int+46 16428000 Int+46 16428001

The manufacturer Westermo Teleindustri AB

SE-640 40 Stora Sundby, Sweden

Herewith declares that the product(s)

Type of product Model Art no

3G Cellular Modem / Router MRD-355 3623-0250

is in conformity with the following EC directive(s).

No Short name

1999/5/EC Radio equipment and Telecommunications terminal equipment (R&TTE)

2011/65/EU Restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS)

References of standards applied for this EC declaration of conformity.

No Title Issue

EN 50385

Product standard to demonstrate the compliance of radio base stations and fixed

terminal stations for wireless telecommunication systems with the basic restrictions

or the reference levels related to human exposure to radio frequency

electromagnetic fields (110 MHz - 40 GHz) - General public

2002

EN 50581

Technical documentation for the assessment of electrical and electronic products

with respect to the restriction of hazardous substances

2012

EN 60950-1

Information technology equipment. Safety. General requirements 2006

+A11:2009

+A1:2010

+A12:2011

+A2:2013

EN 301 489-1

EN 301 489-7

EN 301 489-24

Electromagnetic compatibility and radio spectrum matters (ERM); Electromagnetic

compatibility (EMC) standard for radio equipment and services

Part 1: Common technical requirements

Part 7: Specific conditions for mobile and portable radio and ancillary equipment

of digital cellular radio telecommunications systems (GSM and DCS)

Part 24: Specific conditions for IMT-2000 CDMA Direct Spread (UTRA) for

Mobile and portable (UE) radio and ancillary equipment

2012 (V1.9.2)

2006 (V1.3.1)

2010 (V1.5.1)

EN 301 511

Global system for mobile communications (GSM); Harmonized standard for

mobile stations in the GSM 900 and DCS 1800 bands covering essential

requirements under Article 3(2) of the R&TTE Directive (1999/5/EC)

2003 (V9.0.2)

EN 301 908-1

EN 301 908-2

IMT cellular networks; Harmonized EN covering the essential requirements of

article 3.2 of the R&TTE Directive;

Part 1: Introduction and common requirements

Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)

2013 (V6.2.1)

2014 (V6.2.1)

The last two digits of the year in which the CE marking was affixed: 15

Pierre Öberg

Technical Manager

April 2015

6623-2250

Declaration of Conformity, MRD 455

Westermo Teleindustri AB

Declaration of conformity

Org.nr/

Postadress/Postal address

Tel.

Telefax

Postgiro

Bankgiro

Corp. identity number

Registered office

S-640 40 Stora Sundby 016-428000 016-428001 52 72 79-4 5671-5550 556361-2604 Eskilstuna

Sweden Int+46 16428000 Int+46 16428001

The manufacturer Westermo Teleindustri AB

SE-640 40 Stora Sundby, Sweden

Herewith declares that the product(s)

Type of product Model Art no

4G Cellular Modem / Router MRD-455 3623-0401

is in conformity with the following EC directive(s).

No Short name

1999/5/EC Radio equipment and Telecommunications terminal equipment (R&TTE)

2011/65/EU Restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS)

References of standards applied for this EC declaration of conformity.

No Title Issue

EN 50385

Product standard to demonstrate the compliance of radio base stations and fixed

terminal stations for wireless telecommunication systems with the basic restrictions

or the reference levels related to human exposure to radio frequency

electromagnetic fields (110 MHz - 40 GHz) - General public

2002

EN 50581

Technical documentation for the assessment of electrical and electronic products

with respect to the restriction of hazardous substances

2012

EN 60950-1

Information technology equipment. Safety. General requirements 2006

+A11:2009

+A1:2010

+A12:2011

+A2:2013

EN 301 489-1

EN 301 489-7

EN 301 489-24

Electromagnetic compatibility and radio spectrum matters (ERM); Electromagnetic

compatibility (EMC) standard for radio equipment and services

Part 1: Common technical requirements

Part 7: Specific conditions for mobile and portable radio and ancillary equipment

of digital cellular radio telecommunications systems (GSM and DCS)

Part 24: Specific conditions for IMT-2000 CDMA Direct Spread (UTRA) for

Mobile and portable (UE) radio and ancillary equipment

2012 (V1.9.2)

2006 (V1.3.1)

2010 (V1.5.1)

EN 301 511

Global system for mobile communications (GSM); Harmonized standard for

mobile stations in the GSM 900 and DCS 1800 bands covering essential

requirements under Article 3(2) of the R&TTE Directive (1999/5/EC)

2003 (V9.0.2)

EN 301 908-1

EN 301 908-2

IMT cellular networks; Harmonized EN covering the essential requirements of

article 3.2 of the R&TTE Directive;

Part 1: Introduction and common requirements

Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)

2013 (V6.2.1)

2014 (V6.2.1)

The last two digits of the year in which the CE marking was affixed: 15

Pierre Öberg

Technical Manager

April 2015

6623-2250

Type tests and environmental conditions

Phenomena Test Description Test levels

ESD EN 61000-4-2 Enclosure contact ± 6 kV (crit A)*

Enclosure air ± 8 kV (crit A)*

RF field AM modulated IEC 61000-4-3 Enclosure 10 V/m (crit A)*

(80 – 2700 MHz)

Fast transient EN 61000-4-4 Signal ports ± 1 kV (crit A)*

Power ports ± 2 kV (crit A)*

Surge EN 61000-4-5 Ethernet ports ± 1 kV (direct) (crit B)*

Power ports ± 0.5 kV (line to earth) (crit B)*

± 0.5 kV (line to line) (crit B)*

RF conducted EN 61000-4-6 All ports 10 V/m, (crit A) *

(0.15 – 80 MHz)

Radiated emission EN 55022 Enclosure Class B

Conducted emission EN 55022 DC power ports Class B

Ethernet ports Class B

Temperature Operating –40 to +70ºC

Storage & Transport –40 to +85ºC

Humidity Operating 0 to 90% relative humidity non

condensing.

Storage & Transport 0 to 90% relative humidity non

condensing.

Altitude Operating 2000 m/70 kPa

MTBF MIL-217-F MRD-315 825 759 hours

MRD-355 689 933 hours

MRD-455 689 933 hours

Service life Operating 10 year

Dimension W x H x D 53 x 103 x 134 mm

Weight 0.40 kg

Degree of protection IEC 529 Enclosure IP 40

Cooling Convection

Mounting Horizontal on 35 mm DIN-rail

*crit A = no effect, crit B = restart without user intervention

Altri manuali per MRD-315

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Westermo Router di rete

Westermo

Westermo DR-250 Manuale utente

Westermo

Westermo Lynx 5600 Series Manuale utente

Westermo

Westermo Ibex-330 Series Manuale utente

Westermo

Westermo Viper 008 Manuale utente

Westermo

Westermo DR-260 Manuale utente

Westermo

Westermo Viper 108 Manuale utente

Westermo

Westermo DR-200 Manuale utente

Westermo

Westermo MDI-110-F3G Manuale utente

Westermo

Westermo SDW-550 E-mark Manuale utente

Westermo

Westermo SDI-550 Manuale utente

Westermo

Westermo Lynx L106-F2G Manuale utente

Westermo

Westermo Viper 408 Manuale utente

Westermo

Westermo LRW-112 Series Manuale utente

Westermo

Westermo Falcon Series Manuale utente

Westermo

Westermo Viper 008 Manuale utente

Westermo

Westermo Lynx DSS Manuale utente

Westermo

Westermo Lynx Plus Manuale utente

Westermo

Westermo MRD-415 Manuale utente

Westermo

Westermo RT-370 Manuale utente

Westermo

Westermo Lynx DSS L208-F2G-S2-EX Manuale utente

Westermo

Westermo BRD-355 Manuale utente

Westermo

Westermo MDI-118 Series Manuale utente

Westermo

Westermo Ibex-630 Series Manuale utente

Westermo

Westermo SDW-550 E-mark Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza