Westermo Viper 108 Manuale utente

Managed 8-port

Ethernet Switch

www.westermo.com

©Westermo Teleindustri AB

User Guide

6641-2201

Viper

108 and 408

26641-2201

Legal information

The contents of this document are provided “as is”. Except as required by applicable

law, no warranties of any kind, either express or implied, including, but not limited to,

the implied warranties of merchantability and fitness for a particular purpose, are made

in relation to the accuracy and reliability or contents of this document. Westermo

reserves the right to revise this document or withdraw it at any time without prior

notice.

Under no circumstances shall Westermo be responsible for any loss of data or income

or any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at the following Internet address:

http://www.westermo.com

6641-2201

Safety

Before installation:

Read this manual completely and gather all information on the unit. Make sure that

you understand it fully. Check that your application does not exceed the safe oper-

ating specifications for this unit.

This unit should only be installed by qualified personnel.

This unit should be built-in to an apparatus cabinet, or similar, where access is

restricted to service personnel only.

The power supply wiring must be sufficiently fused (e.g. Littlefuse 0461 1.25), and

if necessary it must be possible to disconnect manually from the power supply. If

fault contact is used, make sure that fault contact wiring is sufficiently fused.

This unit uses convection cooling. To avoid obstructing the airflow around the unit,

follow the spacing recommendations (see Cooling section).

Before mounting, using or removing this unit:

Prevent access to hazardous voltage by disconnecting the unit from power supply.

Warning! Do not open connected unit. Hazardous voltage may occur within this

unit when connected to power supply.

Care recommendations

Follow the care recommendations below to maintain full operation of unit and to fulfil

the warranty obligations.

This unit must not be operating with removed covers or lids.

Do not attempt to disassemble the unit. There are no user serviceable parts inside.

Do not drop, knock or shake the unit, rough handling above the specification may cause

damage to internal circuit boards.

Do not use harsh chemicals, cleaning solvents or strong detergents to clean the unit.

Do not paint the unit. Paint can clog the unit and prevent proper operation.

Do not expose the unit to any kind of liquids (rain, beverages, etc). The unit is not water-

proof. Keep the unit within the specified humidity levels.

Do not use or store the unit in dusty, dirty areas, connectors as well as other mechanical

part may be damaged.

If the unit is not working properly, contact the place of purchase, nearest Westermo dis-

tributor office or Westermo Tech support.

Do not cover or bring mechanical force to the ventilation membrane on the back of the

unit.

Maintenance

No maintenance is required, as long as the unit is used as intended within the specified

conditions.

46641-2201

Agency approvals and standards compliance

Type Approval / Compliance

EMC EN 61000-6-1, Immunity residential environments

EN 61000-6-2, Immunity industrial environments

EN 55024, Immunity IT equipment

EN 61000-6-3, Emission residential environments

EN 61000-6-4, Emission industrial environments

EN 50121-3-2, Railway applications - EMC: Rolling stock – Apparatus

FCC part 15 Class B

EN 50121-4, Railway signalling and telecommunications apparatus

IEC 62236-4, Railway signalling and telecommunications apparatus

E-Mark, Road Vehicles, E1 no: 10 R - 0472161

Safety EN 60950-1, IT equipment

Note 1 _ Applicable only for 3641-6360

FCC Part 15.105 Notice: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a partic-

ular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

… Reorient or relocate the receiving antenna

… Increase the separation between the equipment and receiver

… Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

… Consult the dealer or an experienced radio/TV technician for help.

6641-2201

Declaration of Conformity

Westermo Teleindustri AB

Declaration of conformity

Org.nr/

Postadress/Postal address

Tel.

Telefax

Postgiro

Bankgiro

Corp. identity number

Registered office

S-640 40 Stora Sundby 016-428000 016-428001 52 72 79-4 5671-5550 556361-2604 Eskilstuna

Sweden Int+46 16428000 Int+46 16428001

The manufacturer

Westermo Teleindustri AB

SE-640 40 Stora Sundby, Sweden

Herewith declares that the product(s)

Type of product Model Art no

Unmanaged Ethernet switch Viper-008 3641-0340

Managed Ethernet switch

Viper-408 3641-0360

Viper-408 E-mark 3641-6360

is in conformity with the following EC directive(s).

No Short name

2004/108/EC Electromagnetic Compatibility (EMC)

2006/95/EC Low Voltage (LVD)

2011/65/EU Restriction of the use of certain hazardous substances in electrical and electronic

equipment (RoHS)

References of standards applied for this EC declaration of conformity.

No Title Issue

EN 55022 Information technology equipment - Radio disturbance characteristics - Limits

and methods of measurement

2006

+A1:2007

EN 55024 Information technology equipment - Immunity characteristics - Limits and

methods of measurement

1998

+A1:2001

+A2:2003

EN 61000-6-1 Electromagnetic compatibility - Generic standards - Immunity for residential,

commercial and light-industrial environments

2007

EN 61000-6-2 Electromagnetic compatibility - Generic standards - Immunity for industrial

environments

2005

EN 61000-6-3 Electromagnetic compatibility – Emission for residential environments 2007

EN 61000-6-4 Electromagnetic compatibility - Generic standards - Emission standard for

industrial environments

2007

EN 50121-3-2 Railway applications – Electromagnetic compatibility – Rolling stock -

Apparatus

2006

EN 50121-4 Railway applications – Electromagnetic compatibility – Emission and immunity

of the signaling and telecommunications apparatus

2006

EN 60950-1 Information technology equipment – Safety – General requirements 2006

The last two digits of the year in which the CE marking was affixed: 14

Pierre Öberg

Technical Manager

12th Mars 2014

66641-2201

Type tests and environmental conditions

Phenomena Test Description Test levels

ESD EN 61000-4-2 Enclosure contact ± 6 kV (crit A)

Enclosure air ± 8 kV (crit A)

RF field AM modulated IEC 61000-4-3 Enclosure 20 V/m 80% AM (1 kHz),

80 – 2500 MHz (crit A)

Fast transient EN 61000-4-4 Ethernet ports ± 2 kV (crit A)

Power port ± 2 kV (crit A)

Earth port ± 2 kV (crit A)

Surge EN 61000-4-5 Fault port ± 2 kV line to earth (crit A)

Ethernet ports ± 2 kV line to earth (crit A)

Power port ± 2 kV line to earth, ± 2 kV line to line

(crit A)

RF conducted EN 61000-4-6 Ethernet ports 10 V 80% AM (1 kHz), 0.15 – 80 MHz

(crit A)

Power port 10 V 80% AM (1 kHz), 0.15 – 80 MHz

(crit A)

Power frequency magnetic

field

EN 61000-4-8 Enclosure 1000 A/m 50 Hz

300 A/m 16.7 Hz, 60 Hz, DC (crit A)

Pulse magnetic field EN 61000-4-9 Enclosure 300 A/m (crit A)

Voltage dips and interruption EN 50155 DC power ports 10 ms interruption, 100 ms ±40% voltage

variation

Radiated emission EN 55022 Enclosure Class B

FCC part 15 Class B

Conducted emission EN 55022 DC power port &

Ethernet ports

Class B

FCC part 15 DC power port Class B

Dielectric strength EN 50155 Ethernet ports to other

isolated ports

707 VDC 1 min

Power & Fault port to

other isolated ports

2121 VDC 1 min

Temperature Operating –40 to +70ºC

Storage & Transport –40 to +70ºC

Humidity Operating 5 to 95% relative humidity

Storage & Transport 5 to 95% relative humidity

Altitude Operating 2000 m / 70 kPa

Reliability prediction (MTBF) MIL-HDBK- 217F Operating Ground Benign:

103 years @ 20ºC

100 years @ 40ºC

90 years @ 60ºC

Ground Mobile:

5.92 years @ 20ºC

5.91 years @ 40ºC

5.88 years @ 60ºC

Service life Operating 10 year

Vibration, random simulated

long life

IEC 60068-2-64,

Cat. 1 class B

(EN 61373)

Not Operating Vertical: 7.9 m/s2

Transverse: 7.9 m/s2

Longitudinal: 7.9 m/s2

3 x 5 h

Vibration, random functional IEC 60068-2-64,

Cat. 1 class B

(EN 61373)

Operating Vertical: 1.0 m/s2

Transverse: 1.0 m/s2

Longitudinal: 1.0 m/s2

3 x 10 min

6641-2201

Phenomena Test Description Test levels

Shock, half sine pulses IEC 60068-2-27,

Cat. 1 class B

(EN 61373)

Operating Vertical: 50 m/s2

Transverse: 50 m/s2

Longitudinal: 50 m/s2

30 ms, 3 x 6 shocks

Shock, sawtooth IEC 60068-2-27,

Cat. 1 class B

(IEEE1478-2001)

Operating Vertical: 100 m/s2

Transverse: 100 m/s2

Longitudinal: 100 m/s2

11 ms, 3 x 6 shocks

Enclosure UL 94 Nickel coated zinc Flammability class V-1

Dimension W x H x D 175 x 100 x 50 mm

Weight 0.8 kg

Degree of protection IEC 529 Enclosure IP 65 when all ports are protected/

connected else IP 40

Cooling Convection

Mounting Wall mounted

86641-2201

Description

Functional description

Viper is a range of switches consisting of two different function levels developed for

rail and industrial applications. To meet the environmental requirements from rail and

harsh industrial applications the switch has rugged M12 Ethernet connectors and full

metal housing. The switch fullfill IP 65 degree of protection when all ports are protected/

connected else IP 40. Our unique FRNT (Fast Recovery of Network Topology) technol-

ogy is the fastest protocol on the market to re-configure a network in the event of any

failure of a link or hardware. Real-time properties are implemented in the Viper108 and

408 in order to achieve determinism for real time critical applications. The Viper-switches

supports QoS (Quality of Service) with four priority queues and strict priority scheduling

as well as HoL (Head of Line Blocking Prevention). All to assure that the data network is

deterministic.

6641-2201

Interface specifications

Power and fault relay port PWR

Rated voltage 24 to 110 VDC

Operating voltage 24 to 110 VDC ±40%

Rated current 40 mA @ 110 VDC

140 mA @ 24 VDC

Rated frequency DC

Inrush current, I2t Max 0.02 A2s @ 24 – 110 VDC

Startup current * 7 Apeak @ 24 – 110 VDC

Polarity Reverse polarity protected

Redundant power input No

Isolation to Connections X1 – X8 and to ground, 1500 VAC.

Fault relay belongs to the same isolation group as the power

supply lines (fault relay signals are also contained within

PWR).

Connection 4 pin male M12 connector with A-code

Connector size M12, recommended cable area 0.5 mm2 recommended

(minimum 0.25 mm2), cable dimensions depend on choice of

M12 connector

Shielded cable Not required, twisted pair is recommended

Fault relay resistance < 10 Ω

Operating voltage Up to 110 VDC

Max continuous current 250 mA

* If external power supply is used it must meet specified startup current.

M12 A-Coded

Power

Connector

Position Direction Description

1 U+ Positive supply voltage

2 Out Alarm relay (status) +

3 0 V Negative supply voltage

4 Out Alarm relay (status) –

Housing Shield Chassis of product (ground)

10 6641-2201

Fault Contact

The Viper switch is equipped with a potential free normally closed fault contact.

The fault contact is a solid state component (relay) that requires power to work and it

is transient protected. Additionally, the fault contact is opened when any of the following

conditions is met:

No voltage on the power supply pin, a voltage level outside the legal voltage range •

or current limitation on the voltage source is applied on the power input.

Link alarm i.e. missing link on any Ethernet port that has link alarm enabled. •

Redundancy Mode activated i.e. one or more FRNT link is down.•

Description of how connection to the fault contact could be done is shown below.

The relay is closed when the unit is OK and open at failure. The relay is of semiconduc-

tor type (no moving parts). It is specified for max current 250 mA continuous,

500 mA peak (10 ms), operational voltage up to 110 V, protected by a 150 VDC-varistor,

ON-resistance less than 10 Ohm, and leakage current max 1 µA.

External relay

+24/48 VDC +

1 kΩ

Viper

2 2

4 4

Viper

To logic input

Input on PLC

Service port

The Service Port should not be used by non other than the Westermo Technical Support

team. Do not connect any device or cable to the Service Port.

Altri manuali per Viper 108

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Westermo Router di rete

Westermo

Westermo Lynx 5600 Series Manuale utente

Westermo

Westermo SDI-880/862 Manuale utente

Westermo

Westermo SDW-500 Manuale utente

Westermo

Westermo DDW-02-B1 Manuale utente

Westermo

Westermo DR-250 Manuale utente

Westermo

Westermo DR-200 Manuale utente

Westermo

Westermo MRD-350 Manuale utente

Westermo

Westermo BRD-355 Manuale utente

Westermo

Westermo MDI-110-F3G Manuale utente

Westermo

Westermo ADSL-350 Manuale utente

Westermo

Westermo SDI-550 Manuale utente

Westermo

Westermo Ibex-330 Series Manuale utente

Westermo

Westermo MRD-315 Manuale utente

Westermo

Westermo Ibex-630 Series Manuale utente

Westermo

Westermo RedFox Manuale utente

Westermo

Westermo Lynx L106-F2G Manuale utente

Westermo

Westermo DR-260 Manuale utente

Westermo

Westermo Viper 008 Manuale utente

Westermo

Westermo Lynx DSS Manuale utente

Westermo

Westermo RedFox Rail Manuale utente

Westermo

Westermo MDI-118 Series Manuale utente

Westermo

Westermo SDW-550 E-mark Manuale utente

Westermo

Westermo MRD-315 Manuale utente

Westermo

Westermo Viper 408 Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza