Westermo RedFox Rail Manuale utente

www.westermo.com

RedFox Rail

Ethernet switch and router

approved for railway usage

WeOS

6641-2223

General information

Legal information

The contents of this document are provided “as is”. Except as required by applicable law,

no warranties of any kind, either express or implied, including, but not limited to, the

implied warranties of merchantability and fitness for a particular purpose, are made in

relation to the accuracy and reliability or contents of this document. Westermo reserves

the right to revise this document or withdraw it at any time without prior notice.

Under no circumstances shall Westermo be responsible for any loss of data or income or

any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at the following Internet address:

www.westermo.com

Software tools

Related software tools are available in the folder software tools under technical support

on the Westermo website.

License and copyright for included Free/Libre Open Source Software

This product includes software developed by third parties, including Free/Libre Open

Source Software (FLOSS). The specific license terms and copyright associated with the

software are included in each software package respectively. Please visit the product web

page for more information.

Upon request, the applicable source code will be provided. A nominal fee may be charged

to cover shipping and media. Please direct any source code request to your normal sales

or support channel.

WeOS Management Guide

This product runs WeOS (Westermo Operation System). Instructions for quick start,

configuration, factory reset and use of USB port are found in the WeOS Management

Guide at www.wetermo.com.

6641-2223

Safety

Before installation:

Read this manual completely and gather all information on the unit. Make sure that

you understand it fully. Check that your application does not exceed the safe oper-

ating specifications for this unit.

This unit should only be installed by qualified personnel.

This unit should be built-in to an apparatus cabinet, or similar, where access is

restricted to service personnel only. The power supply wiring must be sufficiently

fused, recom mended fuse: 4 A slow. It must be possible to manually disconnect

power.

Ensure compliance to national installation regulations.

This unit relies on convection heating. Make sure that it is installed so that the

ambient temperature is within the specified temperature range, e.g. by avoiding

obstruction of the airflow around the unit.

Before mounting, using or removing this unit:

Prevent access to hazardous voltage by disconnecting the unit from all power supply.

WARNING

Do not open connected unit. Hazardous voltage may occur within this unit when

connected to power supply.

Before powering-up, a protective earthing conductor must be connected to the

protective earthing terminal and have a cross-sectional area of at least 1.5 mm².

When this unit is operated at an ambient temperature above +55°C (+131°F),

+55°C (+131°F), the External Surface of Equipment may exceed Touch

Temperature Limit according to EN/IEC/UL 60950-1.

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line

cord.

Care recommendations

Follow the care recommendations below to maintain full operation of unit and to fulfill

the warranty obligations.

This unit must not be operating with removed covers or lids.

Do not attempt to disassemble the unit. There are not any user serviceable parts inside.

Do not drop, knock or shake the unit. Rough handling above the specification may cause

damage to internal circuit boards.

Do not use harsh chemicals, cleaning solvents or strong detergents to clean the unit.

Do not expose the unit to any kind of liquids (rain, beverages, paint etc), unless all

connectors and the ventilation membrane are sufficiently protected.

Do not use or store the unit in dusty or dirty areas, unless all connectors and the

ventilation membrane are sufficiently protected.

Do not cover or bring mechanical force to the ventilation membrane on the back

of the unit.

If the unit is not working properly, contact the place of purchase, nearest Westermo

distributor office or Westermo Tech support.

6641-2223

Maintenance

No maintenance is required, as long as the unit is used as intended within the specified

conditions.

Product disposal

This symbol means that the product shall not be treated as

unsorted municipal waste when disposing of it. It needs to

be handed over to an applicable collection point for recy-

cling electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will

help to reduce hazardous substances and prevent potential

negative consequences to both environment and human

health, which could be caused by inappropriate disposal.

6641-2223

Type Approval / Compliance

EMC EN 50121-3-2, Railway applications – EMC: Rolling stock – Apparatus

EN 50121-4, Railway signalling and telecommunications apparatus

EN 61000-6-1, Immunity residential environments

EN 61000-6-2, Immunity industrial environments

EN 61000-6-3, Emission residential, commercial and light-industrial

environments

EN 61000-6-4, Emission industrial environments

EN 50155, Railway applications, Approval/Compliance

Safety EN 60950-1, IT equipment

Agency approvals and standards compliance

Simplified EU declaration of conformity

Hereby, Westermo declares that the equipment is in compliance with EU directives. The

full EU declaration of conformity and other detailed information are available at the

respective product page at www.westermo.com.

6641-2223

Type tests and environmental conditions

Electromagnetic Compatibility

Phenomena Standard Description Test Levels

ESD EN 61000-4-2 Enclosure contact

discharge immunity

±6 kV

Enclosure air discharge

immunity

±8 kV

RF field AM modulated EN 61000-4-3 Enclosure RF immunity 20 V/m, 80 – 2700 MHz

10 V/m, 2700 – 600 MHz

Fast transients EN 61000-4-4 Signal port immunity ±2 kV

Power port immunity ±2 kV

Surges EN 61000-4-5 Power port immunity ±2 kV (L-E)

±1 kV (L-L)

EN 50155:2001 Power port immunity ±8.4 kV (L-E)

±8.4 kV (L-L)

Conducted RF immunity EN 61000-4-6 Signal port immunity 10 V/m, 0.15 – 80 MHz

Power port immunity 10 V/m, 0.15 – 80 MHz

Power frequency magnetic field EN 61000-4-8 Enclosure immunity 300 A/m, 0, 16.7, 50 Hz

Pulsed magnetic field EN 61000-4-9 Enclosure immunity 300 A/m

Voltage interruption EN 50155 Residual voltage 0% 10 ms

Supply overvoltage and undervoltage EN 50155 Overvoltage 140%

Residual voltage 60%

100 ms & 1000 ms

100 ms

Radiated emission EN 55011

Limits: EN 50121-3-2

Enclosure measurement 40 dBµV/m QP

30 – 230 MHz

47 dBµV/m QP

230 – 1000 MHz

56 dBµV/m AVG

1000 – 3000 MHz

60 dBµV/m AVG

3000 – 6000 MHz

Conducted emission EN 55011

Limits: EN 50121-3-2

Power port

measurement

99 dBµV QP

0.15 – 5 MHz

93 dBµV QP

5 – 30 MHz

Signal port

measurement

99 dBµV QP

0.15 – 5 MHz

93 dBµV QP

5 – 30 MHz

Environmental

Temperature EN 60068-2-1

EN 60068-2-2

Operating –40 to +70°C

(–40 to +158°F)

Storage & Transport –40 to +85°C

(–40 to +185°F)

Humidity EN 60068-2-30 Operating 5 to 95% relative humidity

Storage & Transport 5 to 95% relative humidity

Altitude Operating 2 000 m / 70 kPa

Reliability prediction (MTBF) MIL-HDBK- 217F Operating 305,000 hours

Vibration IEC 60068-2-64 Operating Vertical 2.0 m/s² Transverse

2.0 m/s² Longit. 2.0 m/s²

Non operating 11.4 m/s²

Shock IEC 60068-2-27 Operating 10 g, 30 ms Half sine ±3 shocks

IEEE 1478 Operating 20 g, 11 ms Saw tooth ±3 shocks

Packaging

Dimension W x H x D 175 x 100 x 144 mm

Weight 2295 g

Degree of protection IEC 529 Enclosure IP65

Cooling Convection

Mounting Rear panel wall mounting

6641-2223

Description

Functional description

RFR-212-FB is a switch developed for rail on board and industrial applications, approved

according to EN 50155. To meet the environmental requirements from rail and harsh

industrial applications the switch is equipped with rugged M12 Ethernet connectors and

full metal housing and it fulfills IP 65 ingress protection. The unique FRNT (Fast Recovery

of Network Topology) technology is the fastest protocol on the market to re-configure

a network in the event of any failure of a link or hardware. RFR-212-FB supports QoS

(Quality of Service) with four priority queues and strict priority scheduling as well as

HoL (Head of Line Blocking Prevention), in order to assure a deterministic behaviour

of the network. In the event of power loss or other switch failure, the RFR-212-FB is

equipped with dual by-pass relays which can maintain communication through the switch

of dual backbone links.

6641-2223

Interface specifications

Power

Rated voltage 24 to 110 VDC

Operating voltage 16.8 to 143 VDC

(14.4 to 154 VDC for 100 ms)

Rated current

(using Westermo USB plug)

470 mA @ 24 VDC

130 mA @ 110 VDC

Inrush current 5 mA²s @ 24 VDC

79 mA²s @ 110 VDC

Startup current

(Power source capability)

600 mA @ 24 VDC

250 mA @ 110 VDC

Polarity Reverse polarity protected

Redundant power input No

Isolation to All interfaces and chassis

Galvanic connection to None

Connection M12 A-coded male

Connector size 0.2 – 2.5 mm² (AWG 24 – 13)

Shielded cable Not required

Miscellaneous –

M12 A-Coded Power Connector

Position Direction Description

2 1

3 4

1 U+ Positive supply voltage

2 – –

30 V 0 V

4 – –

Housing Shield Chassis of product (ground)

6641-2223

Ethernet TX (both switch, router and coupler ports)

Electrical specification IEEE std 802.3. 2000 Edition

Data rate 10 Mbit/s or 100 Mbit/s, manual or auto

Protocol –

Duplex Full or half, manual or auto

Circuit type TNV-1

Transmission range 100 m (328 ft)

Isolation to All interfaces and chassis

Galvanic connection to None

Connection M12 D-coded

Shielded cable Ye s

Conductive housing Ye s

Miscellaneous –

FRNT reconfiguration time Typically below 20 ms

Number of ports 12

M12 D-coded, 10/100Base-TX

Position Direction Description

1 Out Transmit Data +

2 In Receive Data +

3 Out Transmit Data –

4 In Receive Data –

Housing Shield Chassis of product (ground)

Indice

Altri manuali Westermo Router di rete

Westermo

Westermo SDI-550 Manuale utente

Westermo

Westermo DR-250 Manuale utente

Westermo

Westermo Viper 008 Manuale utente

Westermo

Westermo Ibex-RT-630 Series Manuale utente

Westermo

Westermo RedFox Manuale utente

Westermo

Westermo Lynx 5600 Series Manuale utente

Westermo

Westermo Viper-12 Series Manuale utente

Westermo

Westermo SDW-500 Manuale utente

Westermo

Westermo Ibex-330 Series Manuale utente

Westermo

Westermo Viper 108 Manuale utente

Westermo

Westermo Lynx L106-F2G Manuale utente

Westermo

Westermo Lynx DSS Manuale utente

Westermo

Westermo DR-200 Manuale utente

Westermo

Westermo MRD-315 Manuale utente

Westermo

Westermo Lynx Plus Manuale utente

Westermo

Westermo Falcon Series Manuale utente

Westermo

Westermo Lynx DSS L208-F2G-S2-EX Manuale utente

Westermo

Westermo MDI-110-F3G Manuale utente

Westermo

Westermo LRW-112 Series Manuale utente

Westermo

Westermo SDW-541-F1G-T4G Manuale utente

Westermo

Westermo ADSL-350 Manuale utente

Westermo

Westermo MRD-415 Manuale utente

Westermo

Westermo Viper 408 Manuale utente

Westermo

Westermo SDI-880/862 Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza