Westermo SDW-500 Manuale utente

www.westermo.com

SDW-500 series

Industrial Ethernet 5-port Switch

26644-2214

6644-2214

General information

Legal information

The contents of this document are provided “as is”. Except as required by applicable law,

no warranties of any kind, either express or implied, including, but not limited to, the

implied warranties of merchantability and fitness for a particular purpose, are made in

relation to the accuracy and reliability or contents of this document. Westermo reserves

the right to revise this document or withdraw it at any time without prior notice.

Under no circumstances shall Westermo be responsible for any loss of data or income or

any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at www.westermo.com

About This Guide

This guide is intended for installation engineers and users of the Westermo products.

It includes information on safety and regulations, a product description, installation

instructions and technical specifications.

46644-2214

Safety and Regulations

Warning signs are provided to prevent personal injuries and/or damages to the product.

The following levels are used:

Level of warning Description Consequence

personal injury

Consequence

material damage

WARNING

Indicates a potentially

hazardous situation

Possible death or

major injury

Major damage to the

product

CAUTION

Indicates a potentially

hazardous situation

Minor or moderate

injury

Moderate damage to

the product

NOTICE

Provides information

in order to avoid

misuse of the

product, confusion or

misunderstanding

No personal injury Minor damage to the

product

NOTE

Used for highlighting

general, but important

information

No personal injury Minor damage to the

product

6644-2214

Safety Information

Before installation:

Read this manual completely and gather all information on the product. Make sure that

you understand it fully. Check that your application does not exceed the safe operating

specifications for this product.

WARNING - SAFETY DURING INSTALLATION

The product must be installed and operated by qualified service

personnel and installed into an apparatus cabinet or similar, where

access is restricted to service personnel only.

During installation, ensure a protective earthing conductor is

first connected to the protective earthing terminal (only valid for

metallic housings). Westermo recommends a crosssectional area

of at least 4 mm2.

If the product does not have a protective earthing terminal,

then the DIN-rail must be connected to protective earth. Upon

removal of the product, ensure that the protective earthing

conductor, or the connection to earth via the DIN-rail, is

disconnected last.

WARNING - HAZARDOUS VOLTAGE

Do not open an energized product. Hazardous voltage may occur

when connected to a power supply.

WARNING - PROTECTIVE FUSE

The power supply wiring must be sufficiently fused. It must be

possible to disconnect manually from the power supply. Ensure

compliance to national installation regulations.

Replacing the internal fuse must only be performed by Westermo

qualified personell.

66644-2214

WARNING - REDUCE THE RISK OF FIRE

To reduce the risk of fire, use only telecommunication line cords

with a cable diameter of AWG 26 or larger. Regarding power

cable dimensions, see Interface Specifications.

CAUTION - CORROSIVE GASES

If the product is placed in a corrosive environment, it is important

that all unused connector sockets are protected with a suitable

plug, in order to avoid corrosion attacks on the gold plated

connector pins.

CAUTION - CLASS 1 LASER PRODUCT

Do not look directly info a fibre optical port or any connected

fibre, although the product is designed to meed the Class 1 Laser

regulations and complies with 21 CFR 1040.10 and 1040.11.

CAUTION - ELECTROSTATIC DISCHARGE (ESD)

Prevent electrostatic discharge damages to internal electronic

parts by discharging your body to a grounding point (e.g. use a

wrist strap).

CAUTION - FIBRE OPTIC HANDLING

Fibre optic equipment need special treatment. It is very sensitive

to dust and dirt. If the fibre is disconnected from the product, the

protective plugs on the transmitter/receiver must be connected.

The protective plugs must be kept on during transportation. The

fibre optics cables must be handled the same way.

6644-2214

Care recommendations

Follow the care recommendations below to maintain full operation of product and to

fulfil the warranty obligations:

• Do not drop, knock or shake the product. Rough handling above the specification may

cause damage to internal circuit boards.

• Use a dry or slightly water-damp cloth to clean the product. Do not use harsh

chemicals, cleaning solvents or strong detergents.

• Do not paint the product. Paint can clog the product and prevent proper operation.

If the product is used in a manner not according to specification, the protection provided

by the equipment may be impaired.

If the product is not working properly, contact the place of purchase, nearest Westermo

distributor office or Westermo technical support.

Cleaning of the optical connectors

In the event of contamination, the optical connectors should be cleaned by the use of

forced nitrogen and some kind of cleaning stick.

Recommended cleaning fluids:

• Methyl-, ethyl-, isopropyl- or isobutyl-alcohol

• Hexane

• Naphtha

Product disposal

This symbol means that the product shall not be treated

as unsorted municipal waste when disposing of it. It needs

to be handed over to an applicable collection point for

recycling electrical and electronic equipment.

By ensuring the product is disposed of correctly, you will

help to reduce hazardous substances and prevent potential

negative consequences to both environment and human

health, which could be caused by inappropriate disposal.

86644-2214

Article number, model and description

Article Model Description

3644-0001 SDW-550 10/100Base-T/TX: 5 ports

3644-6001 SDW-550 E-mark 10/100Base-T/TX: 5 ports

3644-0020 SDW-541-MM-SC2 10/100Base-T/TX: 4 ports 100Base-FX: 1 port

3644-0022 SDW-541-SM-LC15 10/100Base-T/TX: 4 ports 100Base-FX: 1 port

3644-0023 SDW-541-MM-LC2 10/100Base-T/TX: 4 ports 100Base-FX: 1 port

3644-0024 SDW-541-SM-SC15 10/100Base-T/TX: 4 ports 100Base-FX: 1 port

3644-0030 SDW-532-MM-SC2 10/100Base-T/TX: 3 ports 100Base-FX: 2 port

3644-0032 SDW-532-SM-LC15 10/100Base-T/TX: 3 ports 100Base-FX: 2 port

3644-0033 SDW-532-MM-LC2 10/100Base-T/TX: 3 ports 100Base-FX: 2 port

3644-0034 SDW-532-SM-SC15 10/100Base-T/TX: 3 ports 100Base-FX: 2 port

3644-0035 SDW-532-SM-LC40 10/100Base-T/TX: 3 ports 100Base-FX: 2 port

Simplified EU declaration of conformity

Hereby, Westermo declares that the equipment is in compliance with EU directives.

The full EU declaration of conformity and other detailed information are available at the

respective product page at www.westermo.com.

6644-2214

Agency approvals and standards compliance

Type Approval / Compliance

EMC EN 61000-6-2, Immproducty industrial environments

EN 61000-6-31, Emission residential environments

EN 61000-6-42, Emission industrial environments

E-Mark, Road Vehicles, 10R-04 72163

Safety UL 60950-1, IT Equipment

Marine DNV GL rules for classification – Ships and offshore products4

Note 1 _ Applicable only for 3644-x001

2 _ Applicable only for 3644-0019, 3644-002x and 3644-003x

3_ Applicable only for 3644-6001

4– Applicable only for 3644-0001, 3644-0022 , 3644-0023, 3644-0025,

3644-0032, 3644-0033, 3644-0035

CAUTION - CORROSIVE GASES

If the product is placed in a corrosive environment, it is important

that all unused connector sockets are protected with a suitable

plug, in order to avoid corrosion attacks on the gold plated

connector pins.

Corrosive

environment:

This product has been successfully tested in a corrosion test according to

IEC 60068-2-60, method 3. This means that the product meets the requirements

to be placed in an environment classified as ISA-S71.04 class G3.

10 6644-2214

Environmental conditions

Isolation between interfaces

Power Interface to all other 2.8 kV DC 2.0 kV RMS @ 50 Hz and 60 s duration

TX signal Interface to all other 2.1 kV DC 1.5 kV RMS @ 50 Hz and 60 s duration

TX shield Interface to all other 1.5 kV DC 1.0 kV RMS @ 50 Hz and 60 s duration

Environmental

Temperature, operating –25 to +70°C (SDW-550),

–25 to +65°C (SDW-541)

–25 to +60°C (SDW-532)

Temperature, storage and transportation –25 to +70°C

Relative humidity, operating 5 to 95% (non-condensing)

Relative humidity,

storage and transportation

5 to 95% (condensation allowed outside packaging)

Altitude, operating 2000 m/70 kPa

Mechanical

Dimension (W x H x D) 35 x 121 x 119 mm

Weight 0.2 kg

Mounting DIN-rail

Degree of protection IP21

Configuration

Auto configured (auto-negotiation) or manually setting of speed and duplex of individual TX port,

by DIP-switches.

Port mirror function is possible to set with DIP-switch. With the port mirror function active the

switch will copy all outgoing traffic to port 1. This can be used to monitor all traffic going out

from the switch. Packets may be discarded if the total throughput exceeds the port speed of port

Fibre optic power budget

Model Multimode

MM-xx2

Singlemode

SM-SC15

Singlemode

SM-LC15

Singlemode

SM-LC40

Transmitted wavelength 1310 nm 1310 nm 1310 nm 1310 nm

Min. output power, transmitter –19 dBm –15 dBm –15 dBm –5 dBm

Max. output power, transmitter –12 dBm –8 dBm -8 dBm 0 dBm

Input sensitivity, receiver –31 dBm –34 dBm –31 dBm –34 dBm

Min. power budget 12 dBm 19 dBm 16 dBm 29 dBm

Max. power budget 19 dBm 26 dBm 23 dBm 34 dBm

Recommended fibre cable and

core / cladding diameter

50/125

62.5/125

9/125

10/125

9/125

10/125

9/125

10/125

Attenuation in connectors / splices

Type Normal attenuation

Connector 0.2 - 0.4 dBm

Fusion splice 0.1 dBm

Mechanical splice 0.2 dBm

Altri manuali per SDW-500

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Westermo Interruttore

Westermo

Westermo MRI-128-F4G Series Manuale utente

Westermo

Westermo RedFox-5528-E-T28G-LV Manuale utente

Westermo

Westermo SD-300 Series Manuale utente

Westermo

Westermo RedFox 5528 Series Manuale utente

Westermo

Westermo Viper-112A-P8-HV Manuale utente

Westermo

Westermo Viper 12A Series Manuale utente

Westermo

Westermo Lynx L110 F2G EX Manuale utente

Westermo

Westermo RedFox 5528 Series Manuale utente

Westermo

Westermo Lynx L210-F2G-EX Manuale utente

Westermo

Westermo Viper 008 Manuale utente

Westermo

Westermo U200 series Manuale utente

Westermo

Westermo PMI-110-F2G Manuale utente

Westermo

Westermo MRI-128-F4G-PSE Series Manuale utente

Westermo

Westermo Viper 12A-PoE Series Manuale utente

Westermo

Westermo Lynx DSS L108-F2G-S2 EX Manuale utente

Westermo

Westermo RedFox 5728 Series Manuale utente

Westermo

Westermo Lynx DSS L205-S1-EX Manuale utente

Westermo

Westermo Viper 12A Series Manuale utente

Westermo

Westermo Viper-TBN Series Manuale utente

Westermo

Westermo Lynx DSS L108-F2G-S2 EX Manuale utente

Westermo

Westermo RedFox Industrial EX Series Manuale utente

Westermo

Westermo Lynx SERIES Manuale utente

Westermo

Westermo Viper-8 Series Manuale utente

Westermo

Westermo Viper TBN Series Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente