Westermo Viper-008 Manuale utente

Viper-008

Unmanaged 8-port Ethernet Switch

www.westermo.com

26641-2211

6641-2211

General Information

Legal Information

The contents of this document are provided “as is”. Except as required by applicable law,

no warranties of any kind are made in relation to the accuracy and reliability or contents

of this document, either expressed or implied, including but not limited to the implied

warranties of merchantability and fitness for a particular purpose. Westermo reserves

the right to revise this document or withdraw it at any time without prior notice.

Under no circumstances shall Westermo be responsible for any loss of data or income

or any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at www.westermo.com

46641-2211

Safety and Regulations

Warning signs are provided to prevent personal injury and/or damages to the product.

The following levels are used:

Level of warning Description Consequence

personal injury

Consequence

material damage

WARNING

Indicates a potentially

hazardous situation

Possible death or

major injury

Major damage to the

product

CAUTION

Indicates a potentially

hazardous situation

Minor or moderate

injury

Moderate damage to

the product

NOTICE

Provides information

in order to avoid

misuse of the

product, confusion or

misunderstanding

No personal injury Minor damage to the

product

NOTE

Used for highlighting

general, but important

information

No personal injury Minor damage to the

product

6641-2211

Before Installation

Read this manual completely and gather all information on the product. Make sure that

you understand it fully. Check that your application does not exceed the safe operating

specifications for this product.

SAFETY DURING INSTALLATION

The product must be installed by qualified service personnel

and built in to an apparatus cabinet or similar, where access is

restricted to service personnel only.

Refer to Compliance Information to see the required level of

qualified service personnel according to safety standards.

During installation, ensure a protective earthing conductor is

first connected to the protective earthing terminal (only valid for

metallic housings). Westermo recommends a cross-sectional area

of at least 4 mm2.

Upon removal of the product, ensure that the protective earthing

conductor is disconnected last.

HAZARDOUS VOLTAGE

Do not open an energized product. Hazardous voltage may occur

when connected to a power supply.

PROTECTIVE FUSE

The power supply wiring must be sufficiently fused. The fuse must

be IEC 60127 certified and rated for T1.25 A and 250 V.

It must be possible to disconnect manually from the power supply.

Ensure compliance to national installation regulations.

This product has no internal fuse and should be connected via an

external fuse for protection.

66641-2211

HOT SURFACE

Be aware that the surface of this product may become hot.

When it is operated at high temperatures, the external surface

may exceed Touch Temperature Limit according to the product's

relevant electrical safety standard.

ELECTROSTATIC DISCHARGE (ESD)

Prevent electrostatic discharge damages to internal electronic

parts by discharging your body to a grounding point (e.g. use a

wrist strap).

REDUCE THE RISK OF FIRE

To reduce the risk of fire, use only telecommunication line cords

with a cable diameter of AWG 26 or larger. Regarding power

cable dimensions, see Interface Specifications.

6641-2211

Care Recommendations

Follow the care recommendations below to maintain full operation of product and to

fulfill the warranty obligations:

• Do not drop, knock or shake the product. Rough handling above the specification

may cause damage to internal circuit boards.

• Use a dry or slightly water-damp cloth to clean the product. Do not use harsh

chemicals, cleaning solvents or strong detergents.

• Do not paint the product. Paint can clog the product and prevent proper operation.

If the product is used in a manner not according to specification, the protection provided

by the equipment may be impaired.

If the product is not working properly, contact the place of purchase, nearest Westermo

distributor office or Westermo technical support.

Product Disposal

This symbol means that the product shall not be treated

as unsorted municipal waste when disposing of it. It needs

to be handed over to an applicable collection point for

recycling electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will

help to reduce hazardous substances and prevent potential

negative consequences to both environment and human

health, which could be caused by inappropriate disposal.

86641-2211

Agency Approvals and Standards Compliance

Type Approval / Compliance

EMC EN 61000-6-1, Immunity residential environments

EN 61000-6-2, Immunity industrial environments

EN 61000-6-3, Emission residential environments

EN 61000-6-4, Emission industrial environments

EN 50121-3-2, Railway applications - EMC: Rolling stock - Apparatus

EN 50121-4, Railway signalling and telecommunications apparatus

IEC 62236-4, Railway signalling and telecommunications apparatus

Environmental EN 50155 Railway applications - Electronic equipment used on rolling

stock

Fire protection EN 45545-2, Fire protection on railway vehicles

Safety EN/IEC/UL 62368-1, Safety Requirements for audio/video, information

and communication technology equipment

Compliance Information

EN/IEC/UL 62368-1 Notice

This product has been tested and found compliant to EN/IEC/UL 62368-1, Safety

for Communication Technology. In accordance with the definitions of the standard,

this product shall be handled by ordinary personnel. Energy source classifications are

according to following:

EN/IEC/UL 62368-1 notice

Electrical energy source Power port ES1 (at 24 VDC)

ES3 (at 110 VDC)

Serial port ES1

Ethernet port ES1, TNV-1

Power source Power port PS3

Thermal energy source Enclosure TS1

Mechanical energy

source

Enclosure MS1 (MS3 for wall or ceiling

mounting)

Radiation energy source N/A N/A

6641-2211

Declaration of Conformity

Hereby, Westermo declares that this product is in compliance with applicable EU

directives and UK legislations. The full declaration of conformity and other detailed

information is available at www.westermo.com/support/product-support.

FCC Part 15.105 Notice:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

… Reorient or relocate the receiving antenna

… Increase the separation between the equipment and receiver

… Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected

… Consult the dealer or an experienced radio/TV technician for help.

10 6641-2211

Type Tests and Environmental Conditions

Phenomena Test Description Test levels

ESD EN 61000-4-2 Enclosure contact ± 6 kV (crit A)

Enclosure air ± 8 kV (crit A)

RF field AM modulated IEC 61000-4-3 Enclosure 20 V/m 80% AM (1 kHz),

80 - 2500 MHz (crit A)

10 V/m 80% AM (1 kHz),

2700 - 6000 MHz (crit A)

Fast transient EN 61000-4-4 Ethernet ports ± 2 kV (crit A)

Power port ± 2 kV (crit A)

Earth port ± 2 kV (crit A)

Surge EN 61000-4-5 Fault port ± 2 kV line to earth (crit A)

Ethernet ports ± 2 kV line to earth (crit A)

Power port ± 2 kV line to earth, ± 2 kV line to line

(crit A)

RF conducted EN 61000-4-6 Ethernet ports 10 V 80% AM (1 kHz), 0.15 - 80 MHz

(crit A)

Power port 10 V 80% AM (1 kHz), 0.15 - 80 MHz

(crit A)

Power frequency magnetic

field

EN 61000-4-8 Enclosure 1000 A/m 50 Hz

300 A/m 16.7 Hz, 60 Hz, DC (crit A)

Pulse magnetic field EN 61000-4-9 Enclosure 300 A/m (crit A)

Voltage dips and interruption EN 50155 DC power ports 10 ms interruption, 100 ms ±40% voltage

variation

Radiated emission CISPR 16-2-3

ANSI C63.4

(FCC part 15)

Enclosure Class B (30 - 6000 MHz)

Conducted emission CISPR 16-2-1 DC power port &

Ethernet ports

Class B

Dielectric strength EN 50155 Ethernet ports to other

isolated ports

500 VAC 1 min

Power & Fault port to

other isolated ports

1500 VAC 1 min

Temperature EN 60068-2-1

EN 60068-2-2

Operating -40 to +70ºC

Storage & Transport -40 to +85ºC

Humidity EN 60068-2-30 Operating 5 to 95% relative humidity

Storage & Transport 5 to 95% relative humidity

Altitude Operating 2000 m / 70 kPa

Reliability prediction (MTBF) MIL-C217F2, GB Operating 150 years @ 20 ºC

147 years @ 40 ºC

135 years @ 60 ºC

Service life Operating 10 years

Vibration, random simulated

long life

IEC 60068-2-64,

Cat. 1 class B

(EN 61373)

Not Operating Vertical: 7.9 m/s2

Transverse: 7.9 m/s2

Longitudinal: 7.9 m/s2

3 x 5 h

Vibration, random functional IEC 60068-2-64,

Cat. 1 class B

(EN 61373)

Operating Vertical: 1.0 m/s2

Transverse: 1.0 m/s2

Longitudinal: 1.0 m/s2

3 x 10 min

Shock, half sine pulses IEC 60068-2-27,

Cat. 1 class B

(EN 61373)

Operating Vertical: 50 m/s2

Transverse: 50 m/s2

Longitudinal: 50 m/s2

30 ms, 3 x 6 shocks

Indice

Altri manuali Westermo Interruttore

Westermo

Westermo Lynx L110 F2G EX Manuale utente

Westermo

Westermo Lynx DSS L108-F2G-S2 EX Manuale utente

Westermo

Westermo L110-F2G Manuale utente

Westermo

Westermo Viper TBN Series Manuale utente

Westermo

Westermo Lynx SERIES Manuale utente

Westermo

Westermo Lynx SERIES Manuale utente

Westermo

Westermo RFIR-127-F4G-T7G-DC Manuale utente

Westermo

Westermo Lynx DSS L108 Manuale utente

Westermo

Westermo MRI-128-F4G Series Manuale utente

Westermo

Westermo PMI-110-F2G Manuale utente

Westermo

Westermo Lynx DSS L108-F2G-S2 EX Manuale utente

Westermo

Westermo Viper-12 Series Manuale utente

Westermo

Westermo Lynx DSS L206-S2-EX Manuale utente

Westermo

Westermo Lynx-3510-F2G-P8G-LV Manuale utente

Westermo

Westermo Lynx 3000 Series Manuale utente

Westermo

Westermo RedFox 5528 Series Manuale utente

Westermo

Westermo PSI-010-FT2G-P8G Manuale utente

Westermo

Westermo RedFox 5528 Series Manuale utente

Westermo

Westermo Lynx DSS L205-S1-EX Manuale utente

Westermo

Westermo RedFox Industrial EX Series Manuale utente

Westermo

Westermo Viper-120A-P8-HV Manuale utente

Westermo

Westermo Viper-12-PoE Manuale utente

Westermo

Westermo Lynx L206-F2G-EX Manuale utente

Westermo

Westermo Lynx DSS L108-F2G-S2 EX Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente