Whelen Engineering Company IS1 Series Manuale utente

ENGINEERING COMPANY, INC IS1 SERIES

MICRO SIZE

STROBE BEACONS

IS1224P, 12-48 VDC, PIPE MOUNT

IS1120P, 120 VAC, PIPE MOUNT

IS1224S, 12-48 VDC, SURFACE MOUNT

IS1120S, 120 VAC, SURFACE MOUNT

IS124CP, 12-48 VDC, CAST, PIPE MOUNT

Doc No. 04-0113085-01

Route 145, Winthrop Road

Chester, CT06412-0684

TELEPHONE: (860) 526-9504

TOLL FREE: 1-800-637-4736

1996 Whelen Engineering Company, Inc. Doc No. 04-0113085-01

May 24, 1996. 13085B

BASE

O RING SEAL

PCB ASSEMBLY

STROBE TUBE ASSEMBLY

#6-32 SCREW

CLAMP RING

DOME

STOP NUT

WARNING ALWAYS

DISCONNECT POWER

BEFORE SERVICING OR

INSTALLING AN IS1

SERIES BEACON.

SEE OTHER SIDE OF PAGE FOR

REPLACEMENT PARTS LISTING.

DESCRIPTION QTY. PART NUMBER

STROBE TUBE ASSEMBLY 1 01-0441319-00

DOME, AMBER 1 68-2130024-10

DOME, BLUE 1 68-2130024-20

DOME, CLEAR 1 68-2130024-30

DOME, GREEN 1 68-2130024-40

DOME, RED 1 68-2130024-50

O RING SEAL, PLASTIC BASE 1 38-0416442-00

GASKET, CAST BASE 1 38-0230104-00

MOUNTING INSTRUCTIONS

The IS1 Series Beacons are made for permanent

surface mount or pipe mount on a 1/2” NPT thread.

SURFACE MOUNT, PLASTIC BASE

1. Locate the wires in the wire slot and mount with

two screws. Make sure that the wires are in the wire

slot and not pinched under the Base.

PIPE MOUNT (Internal Thread)

1. Feed the power wires through the pipe.

2. Wire according to the WIRING instructions.

3. Screw the base onto the 1/2” NPT pipe and hand

tighten.

WIRING INSTRUCTIONS

MODELS IS1224P and IS1224S

MODEL IS124CP

1. Connect the RED wire to the positive DC

voltage (+).

2. Connect the BLACK wire to DC ground (-).

MODELS IS1120P and IS1120S

1. Connect the BLACK wire to the AC hot wire.

2. Connect the WHITE wire to the AC return wire.

Refer to the IS1 Series Product Sheet for current

draw to determine the proper wire gauge.

STROBE TUBE REPLACEMENT

1. Turn off power and wait 10 minutes.

2. Loosen the clamp ring screw and remove the

dome. Save the O Ring.

3. Press the tabs together on the Strobe Tube

Assembly and firmly pull the assembly out of the

PCB assembly. Do not pull the PCB Assembly away

from the Base.

4. Snap the replacement Strobe Tube Assembly into

the PCB Assembly. Roll the O Ring down the Base,

to get it in position. Position the Dome and secure

the clamp ring.

IS1 SERIES REPLACEMENT PARTS LISTING

3.4"

3.8" 2.5" DIA

1996 Whelen Engineering Company, Inc. Doc No. 04-0113085-01

May 24, 1996.

Questo manuale è adatto per i seguenti modelli

Altri manuali Whelen Engineering Company Sistema di sicurezza

Whelen Engineering Company

Whelen Engineering Company L22H Series Manuale utente

Whelen Engineering Company

Whelen Engineering Company WS295HFS1 Series Istruzioni per l'installazione

Whelen Engineering Company

Whelen Engineering Company ISB Series Manuale utente

Whelen Engineering Company

Whelen Engineering Company GTT 795DM Manuale utente

Whelen Engineering Company

Whelen Engineering Company 6220-01-057-0746 Manuale utente

Whelen Engineering Company

Whelen Engineering Company IPS 400 Manuale utente

Whelen Engineering Company

Whelen Engineering Company 295HFS4 Series Manuale utente

Whelen Engineering Company

Whelen Engineering Company WeCanX Traffic Advisor Module Manuale utente

Whelen Engineering Company

Whelen Engineering Company RB6PAPS Manuale utente

Whelen Engineering Company

Whelen Engineering Company SSNF360 Manuale utente

Whelen Engineering Company

Whelen Engineering Company Traffic Advisor TA837A Manuale utente

Whelen Engineering Company

Whelen Engineering Company 295HFSA5 Manuale utente

Whelen Engineering Company

Whelen Engineering Company 1502M Manuale utente

Whelen Engineering Company

Whelen Engineering Company RB6T Manuale utente

Whelen Engineering Company

Whelen Engineering Company 2015 Series Manuale utente

Whelen Engineering Company

Whelen Engineering Company WPS-2900 Series Manuale utente

Whelen Engineering Company

Whelen Engineering Company SS361 Manuale utente

Whelen Engineering Company

Whelen Engineering Company B6LED Series Manuale utente

Whelen Engineering Company

Whelen Engineering Company IS3 Series Manuale utente

Whelen Engineering Company

Whelen Engineering Company 295SLSA5 Manuale utente

Whelen Engineering Company

Whelen Engineering Company SCSS85 Manuale utente

Whelen Engineering Company

Whelen Engineering Company 2022 Series Manuale utente

Whelen Engineering Company

Whelen Engineering Company RB6T Manuale utente

Whelen Engineering Company

Whelen Engineering Company Super-LED L31HBF Series Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente