Whirlpool 2180913 Manuale utente

Installation

Changing The

Bin Door And

Lower Panels 2

General Information 3

For The Plumber 4

For The Electrician 6

How The

Ice Maker Works 7

Things To

Remember 7

Operating

Instructions 8

Unit Wiring

Diagrams 8

Check Operation 9

AUTOMATIC ICE MAKER

Part No. 2180913

/I%

Changing The Bin Door

And Lower Panels

The storage bin door is designed to accept an

optional decorative wood panel of your choice.

The wood panel should be no more than

l/4inch (6 mm) thick. Cut it to the same size as

the production metal panel.

To change the bin door panel:

I. Open the bin door.

2. Remove the two screws on top of the door

which hold the handle.

3. Remove the handle and handle insert.

4. Slide the metal panel out.

5. Break off all door insulation ribs to allow

room for the wood panel’s thickness.

6. Slide the wood panel into the door frame.

Replace the handle and screws.

To change the lower panel:

1. Remove the three screws that hold the

lower panel assembly to the ice maker.

Remove the two screws on the top of the

panel assembly.

3. Slide the metal panels and spacers out.

4. Slide the wood panel into the door frame.

5. Replace the top of the panel assembly.

NOTE:

Make sure the galvanized panel is

replaced in back of the panel assembly.

Bin door ,

11‘AI” II

Bin door

11‘AI”

(266 mm)(266 mm)

LowerLower

panelpanel

11’%6”11’%6”

(303 mm)(303 mm)

DIMENSIONS

Break off all door

insulation ribs to

accept 1/4”(6mm)

thick wood panels

Thermostat calibrations

If ice maker is installed above 2000 feet (600 m) thermostat, and follow the directions for turning

above sea level, the Bin and Ice Thickness the altitude adjustment screw as shown in the

Thermostats must be adjusted to a warmer label on each thermostat.

setting. Disconnect electricity, remove

Shipboard operation

When this ice maker is installed aboard a ship, grid. It keeps the water flowing over the

it may be necessary to purchase and install a evaporator from spilling into the storage bin

water deflector. The deflector hangs between area. Order the necessary parts from your

the lower edge of the evaporator and the cutter local ice maker dealer.

General Information

Unpack

1. Lay carton on rear face and break open

bottom flaps.

2. Set carton upright with all four flaps outward.

3. Lift carton up and off of machine.

4. Remove all tape and packaging materials

from the outside and inside of the cabinet.

5. Remove the lower access panel by remov-

ing the two screws securing the grille at the

bottom and the one screw at the top, and lift

it free of cabinet.

6. Turn the fan by hand to make certain it

moves freely.

7. Loosen thumb screws holding cutter grid

and water pan to “thumb tight.”

Remove interior

Utilities

OBSERVE LOCAL CODES

Each installation is unique but will require:

1. A cold water inlet of W (6 mm) OD soft

copper tubing and a shut-off valve.

2. A properly grounded 115 Volt, 60 Hz.,

AC only, 15 or 20 ampere electrical circuit,

installed in accordance with the National

Electrical Code and with local codes and

ordinances.

3. Either a gravity drain system or a sump

pump to lift the water to an existing drain.

Electricity

Locate unit

1. Place unit so the front side will be completely

unobstructed to provide proper airflow.

2. Area should be well ventilated with tempera-

ture above 55°F (13°C) and below 110°F

(43°C). Best results are obtained between

70°F (21“C) and 90°F (32%).

3. Provisions for electricity, water, and drain

connections should be determined.

4. The unit may be closed in on the top and

three sides, but the front MUST BE unob-

structed for air circulation and proper opera-

tion. Installation should be such that the

cabinet can be moved forward for servicing,

if necessary.

This unit

MUST be

installed in

an area

protected

from the

elements,

such as

wind, rain,

and water

spray or

drip.

BEST

RANGE

Level unit

1. After placing unit in position, check to make 4. If you are installing this ice maker in a

certain the unit is level side-to-side and commercial setting that requires National

front-to-back. Sanitation Foundation (NSF) installation

2. Accurate leveling is essential for proper procedures, NSF requires that the ice

operation. maker be sealed to the floor at the bottom

3. Unit should be shimmed so that it is solid as rail. For compliance with this NSF sealing

well as level. The shims should be of hard procedure, we recommend a silicone-type

permanent type material such as Masonite. sealer.

For The Plumber

connect to

water

(observe local codes)

1. Use VI” (6 mm) OD soft copper tubing for

the cold water supply.

2. Provide a convenient manual shut-off valve

in the water line.

3. Position the tubing so it can enter the

access hole located in the right hand rear of

the cabinet. The tubing should extend

beyond the cabinet front when the

cabinet is pushed back into position.

NOTES:

Always purge the water line before making the

final connection to the inlet of the water valve

to prevent possible water valve malfunction.

After the cabinet is in place, bend the tubing to

meet the connection at the water valve. The

garden hose-threaded compression fitting is

found in the parts bag. This joint provides a

convenient disconnect for service. Be sure the

tubing is clear of compressor to prevent rattle.

BUILT-IN OPENING DIMENSIONS

1:1: :\:\

II I ‘%I ‘%

900,900, - 90”- 90”

34-l/2”34-l/2”

Do Not kink orDo Not kink or (676 mm)

pinch power ,i

-- 4-112”

supply cord (114mm)to

behveen icebehveen ice center line

maker andmaker and

cabinet. 9” (229 mm)

max.

L 16” (457 mm) --\L 16” (457 mm) --\

RIGHT END VIEW

Y.” 119 mml

l/4” (6 mm)

OD water line

compression

fitting at

water valve \

Bend field- \I

water valve

Water

inlet

solenoid

/ valve

BACK VIEW

34%”

(674 mm]

Hole for

field-

supplied I

water line 7

3”

(76 mm) e

lT/Bp/s”

+200 mm)-

7%”

(19 mm)

4” (102 mm)

long 5/e”(16-

mm) rubber

drain tube -

run to open

drain

1Vi” (32 mm)

minimum

diameter

- standpipe

7- 6

S”

” -

II J--L

f$l+\-I

(36 mm) 9” (23 mm)

-I

Connect to drain

(observe local codes)

1. The unit is provided with a gravity drain.

2. The ideal installation has a standpipe (1-l/4”

[32 mm] minimum) installed directly below

the outlet of the drain tube. Refer to figures

for the proper location of the standpipe.

3. It may be desirable to insulate drain line

thoroughly up to drain inlet.

Connect drain pump

If a drain connection directly below the drain

tube outlet is not available, install a drain pump

in the rear compartment of the ice maker. The

drain pump must meet these specifications:

It must be U.L.-listed and have a U.L.-

listed, 120 VAC, 3-wire, grounded power

supply cord.

Overall maximum outside dimensions: 15”

(381 mm) wide x 6” (152 mm) deep x 9-l/2”

(241 mm) high.

Minimum pump flow rate: 24 gallons

(91 liters) per hour [0.4 gallons (1.5 liters) per

minute] at 12 feet (3.7 m) lift.

Operating temperature range: 55°F (13°C) to

110°F (44°C).

For The Electrician

Electrical1 requirements

A 115 Volt, 60 Hz., AC only, 15 or 20 ampere

electrical supply circuit, properly grounded in

accordance with the National Electrical Code

and local codes and ordinances is required.

It is recommended that a separate circuit,

serving only this appliance, be provided. Use a

receptacle which cannot be turned off with a

switch of pull chain. DO NOT use an extension

cord.

Grounding method

! A-

A *

Electrical Shock Hazard

Electrical ground is required on this

ice maker.

Do Not ground to a gas pipe.

Do Not change the power supply cord

plug. If it does not fit the outlet, have

a proper outlet installed by a qualified

electrician.

Do Not have a fuse in the neutral or

grounding circuit. A fuse in the

neutral or grounding circuit could

result in an electrical shock.

Do Not use an extension cord with

this ice maker.

Check with a qualified electrician if

you are in doubt as to whether the

appliance is properly grounded.

Failure to follow these instructions

could result in death or serious

injury.

3-prong grounding-type

For your personal safety, this appliance

must be grounded. This appliance is

equipped with a power supply cord having

a 3-prong grounding plug. To minimize

possible shock hazard, the cord must be

plugged into a mating

3-prong grounding type wall receptacle,

grounded in accordance with the National

Electrical Code and local codes and

ordinances. If a mating wall receptacle is

not available, it is the personal responsibil-

ity and obligation of the customer to have

a properly grounded 3-prong wall recep-

tacle installed by a qualified electrician.

How The Ice Maker Works

l Compressor runs

. Condenser fan runs

l Water pump runs (circulates water)

l Cutter grid is warm to touch

WHEN THE DESIRED ICE SLAB THICK-

NESS IS REACHED, THE HARVEST CYCLE

BEGINS AND THE FOLLOWING HAPPENS:

l Evaporator thermostat is satisfied

. Compressor keeps running

l Condenser fan stops or turns very slowly

l Water pump stops

l Hot gas solenoid opens

l Water inlet valve opens

l Excess water is flushed out of the drain pan

l Cutter grid is warm to the touch

NOTE: Normal harvest cycle takes 1 to

2 minutes.

MACHINE RESUMES FREEZING AFTER

SLAB IS RELEASED FROM EVAPORATOR

AND THE CUlTING PROCESS BEGINS.

WHEN THE STORAGE BIN IS FILLED, BIN

THERMOSTAT OPENS.

l Cutter grid remains on

Things To Remember

l Water enters only during the defrost cycle

Therefore the first cycle will be completed

without water in the system.

l As the room and water temperatures vary, so

will the amount of ice produced. This means

that higher operating temperatures will result

in reduced ice production.

l The unit will shut off when ice in the storage

bin touches the bin thermostat well and will

automatically cycle to keep the bin full.

l The storage bin is not refrigerated and some

melting will occur. This also varies with the

room temperature.

l The unit needs good air circulation to

perform efficiently. Keep the front grille and

the condenser clean.

l The water system, including filter screen in

the water inlet solenoid valve, needs to be

cleaned periodically for good circulation.

Instructions are located on the inner door

panel.

Operating Instructions

l For complete operation information, refer to

the Use and Care Guide.

l Before starting, wash out interior of cabinet

with a Baking Soda solution (2 tablespoons

[26 grams] soda to 1 quart [l liter] of warm

water). Rinse thoroughly.

l Make certain the water is turned on.

l Turn switch to the “ON” position.

IMPORTANT: Allow unit to run for 3 hours

before expecting ice and for 24 hours before

trying to set the thickness control.

If installed above 2,000 feet (600 m) above

sea level, see page 2 for thermostat

adjustments.

CUBELET GRID

3/4”

3/i”

(19 mm x 19 mm)

Unit Wiring Diagrams

This model operates at 115 volts except for the

cutter grid circuit which operates at 8.5 volts at

1 amp.

The compressor runs at all times except when

the Bin Thermostat becomes satisfied and

opens the circuit. This de-energizes the system

except for the transformer and cutter grid.

Under normal operating conditions, when the

evaporator reaches the preset temperature

(+lO” to -3°F [-12” to -19%], depending on

thickness of ice) the evaporator thermostat

opens, terminating operation of the fan motor

and pump motor. The hot gas solenoid and the

water valve solenoid are energized at this time

and remain so until the evaporator reaches

38” + 2°F (3” + 1“C).

Electrical Shock Hazard

Disconnect power before servicing

unit.

Failure to do so could result in

electrical shock.

NOTE: A 15 or 20-ampere time-delay fuse

or circuit breaker is recommended.

Check Operation

Start the unit by turning the service

switch to “ON” and opening the line d

water valve.

NOTE: Left is “OFF” - Middle is “ON” -

Right is “CLEAN.” In “CLEAN” position,

only the pump operates.

Check condenser fan to make sure it is

revolving. Check for airflow. Do not

insert hand into fan area. d

Water will not enter pump pan until

freezing plate gets cold and machine

goes into a harvest cycle.

Check for even water flow over freezing

plate. Unit must be level for proper

operation.

Check for desired cube thickness and

after 24 hours adjust if necessary. Max-

imum ice yield will be obtained with ice

thickness at %” (13 mm) to %” (16 mm).

Replace grille.

d’installation

Changement du

panneau de la

Porte du receptacle

et du panneau

inferieur

Renseignements

generaux

Instructions a

I’intention du

plombier

Instructions a

I’intention de

I’electricien

Mode de

fonctionnement

Ne pas oublier

Instructions

d’utilisation

Schema de cdblage 8

Controle du

fonctionnement g

MACHINE A GLACONS AUTOMATIQUE

Pike no2180913

Indice

Lingue:

Altri manuali Whirlpool Macchina per il ghiaccio

Whirlpool

Whirlpool AGB 024/01/G/WP Manuale utente

Whirlpool

Whirlpool Cornelius JEACS50SLF1 Manuale utente

Whirlpool

Whirlpool 50 Manuale utente

Whirlpool

Whirlpool WUI95X15HZ Manuale utente

Whirlpool

Whirlpool 2180633 Manuale utente

Whirlpool

Whirlpool W10136155B Manuale utente

Whirlpool

Whirlpool GI15NDXXB1 Manuale utente

Whirlpool

Whirlpool GI15NFRTB0 Manuale utente

Whirlpool

Whirlpool GI15NDXZS Manuale utente

Whirlpool

Whirlpool 50 Manuale utente

Whirlpool

Whirlpool R-66 Manuale utente

Whirlpool

Whirlpool EC5100XP Manuale utente

Whirlpool

Whirlpool WUI95X15HZ Manuale utente

Whirlpool

Whirlpool VERSA CUBER CH E-5R Manuale utente

Whirlpool

Whirlpool GI15NDXX Manuale elenco delle parti

Whirlpool

Whirlpool GI15NFLTB1 Manuale utente

Whirlpool

Whirlpool W10282149B Manuale utente

Whirlpool

Whirlpool GI15NDXTB - 15" 50 lb. Icemaker Manuale utente

Whirlpool

Whirlpool GI15NDXTB0 Manuale utente

Whirlpool

Whirlpool GI15NFRTS - INSTALLATION REV A Manuale utente

Whirlpool

Whirlpool GI15NFRTS - Ice Maker Manuale utente

Whirlpool

Whirlpool EC510 Manuale utente

Whirlpool

Whirlpool GI15NFRT Istruzioni utente

Whirlpool

Whirlpool GI15NDXTB - 15" 50 lb. Icemaker Manuale del proprietario

Manuali Macchina per il ghiaccio popolari di altre marche

Hoshizaki

Hoshizaki KMD-460MWJ Manuale utente

Sub-Zero

Sub-Zero 315I Istruzioni per l’uso

Unold

Unold 48945 Manuale utente

Kenmore

Kenmore 2217402A Manuale utente

Cornelius

Cornelius WM600 Istruzioni operative

GE XPIO43SCSS Manuale utente

Hoshizaki

Hoshizaki KMD-901MAH Manuale utente

Whynter

Whynter FIM-450HA Manuale utente

U-Line

U-Line UMCR014-SC01A Manuale di installazione

Andrew James

Andrew James AJ000522 Manuale utente

Scotsman

Scotsman CME1356 Manuale utente

Scotsman

Scotsman ACM 25 Manuale utente

Kärcher

Kärcher IP 120 Manuale utente

U-Line

U-Line SS1095 Manuale utente

Maytag

Maytag MIM1554WRS - Ice Maker Manuale utente

Hoshizaki

Hoshizaki KM-630MAH Manuale utente

Princess

Princess Yonanas Manuale utente

Unold

Unold 48946 Manuale utente